r/32inchbikes • • 2d ago

Every Test on 32-Inch Wheels in One Video. What's the Verdict?

Thumbnail
youtu.be
16 Upvotes

r/32inchbikes • • 16d ago

Do much heavier wheels ruin your 32" bike? I swapped my carbon wheels for a budget Ryde/CUES set. What did the hot lap attack tell me?

Thumbnail
gallery
7 Upvotes

Aggressive first ride. Bit of a scare on the second.

Riding impressions on the budget Ryde/Shimano 32" wheels. Two good rides in, it's time to offer an early review.

intro
Unboxing post, more pictures and specs:

https://www.reddit.com/r/32inchbikes/comments/1xlx23f/on_test_hand_built_34900_rydecuessapim_wheelset/

This set of all-black hand-built Ryde Disc 30D/Shimano CUES/Sapim Race wheels (€349 as tested) was kindly provided for testing by Andy Los of https://www.andlesscycling.nl/.

These are wheels reduce the minimum cost a lot from the scarce alu 32" options we've seen before. The Ryde Rims and hubs are not kept in stock, but can be ordered for a custom build.

Comparison is with the high-end mid-weight ~€1150 Luther prototype wheels currently on long term test (Andy's carbon wheel brand), soon to be available to the public.

tubeless tire installation
I swapped tires over from carbon wheels to the aluminium wheels. Inflation with a booster pump went easily enough, although the Maxxis fit a bit loosely. Loud assuring tire seating pops.

An initial air leak at the rim joint was sealed with some good wheel shaking. A few bubbles came from a few spoke holes, possibly due the valve not being installed correctly. I tightened up the valve nut and the tires perfectly held pressure for the next days.

the bike
A very heavy (3550 gram) steel custom frame, roughly XL sized, with a reasonably light build kit and carbon rigid fork.
Normally ~12.2 kg, so now ~13.2 kg with the Ryde/CUES wheels. I ride with two large water bottles. Front tire is a Maxxis Aspen AT 32x2.4", rear a Maxxis Aspen ST 2.15". I'd been riding those tires exclusively the 3 weeks prior.

first ride, out the door
The ride plan was simple and kept to that: an 8,5 km (5 mi) out to the trail head, three 9 km (5.5 mi) laps of 227 hm/744 vft) each, and the same route home, 45 km total and just over 2 hours.

9ºC/48-49ºF, chilly enough for me to dress for fall riding.

on the road, first impressions
Confirmation bias. It's easy to feel exactly what you expected, heaving just installed heavier wheels. But how real are those perceptions? What I did notice early on, was the rear hub being near silent, I'd not thought about that beforehand. It felt oddly "exposed" in traffic with the chaos of cyclists and pedestrians now less likely to hear me approach.

Yes, I did seem to sense a bit of a difference to the overall bike. There was a slightly increased "king of the road" feel to it without it necessarily registering as "heavy".

at the trail head
Upon checking, the tires had been holding air well. I aired them down to go hit the trails, but kept in a bit more than I usually run, just in case.

hitting the trails
(Rider: 50 y/o, 194 cm/6'3", 96 kg/212 lbs. 17% over my younger years' weight)

As I usually do, I attack the first singletrack climb, short and anaerobic. Slow start messing with the shifter barrel adjuster, but pushing through.

the home trails I'm hot lapping on
Here's a 7 minute clip from the start of the trail until before the start of the more notable climbs, that was a good effort for me. Filmed a couple months ago on my 29" hardtail. https://www.youtube.com/watch?v=h352NYaRcHU

With the extra heavy 32" bike I went 15 seconds faster over the bit in the video. I did this it faster only ONCE, all the way back in April on a day with crazy perfect tail wind, from my 238 "attempts" at it.

In the little technical downhills, the bike and wheels just felt fine. Perhaps a bit more "solid" than usual. Less lively/bouncy, but not necessarily less agile. If anything I'm making the turns better than usually. The new bike is still growing on me and the trail was never grippier.

8:30 into the hot lap
Great intermediate time still, I'd gotten through the twisties well. However, the anaerobic tank is empty and the suffering starts. By minute 10, I abort the personal lap record attempt as it feels pointless. As I bailed out, I was actually still on my PB pace, to the second, set early May this year on that 29" hardtail. A 2 kg lighter bike and myself another 3 kg lighter. To be matching that pace, I'm absolutely moving on this bike and the wheels can't be holding me back much.

The remainder of the 9 km lap with most of the climbing in it, I ride focusing on taking the little downhills and corners nicely as I can, to limit the time loss from soft pedaling everywhere else. My 25:33 lap is the fastest I've managed in almost 6 months. Only a few attempts in April and May were faster and there have been 150+ "attempts" since. For my 24:19 PB also in early May, I was full on racing all the way to the end.

the answer is no
Not slow at all. It's more about your own fitness and how the tires perform.

anything to gather from that n=1 lap attack?
Only a first impression. These rims and wheels are in fact over twice the weight of some 32" wheels shown on this subreddit. Yet, they don't appear to ruin my ride, at all. The stopwatch doesn't seem able to be able to tell that I'm hauling around 8% more bike weight, nearly 1% of extra vehicle mass, all in the wheels.

It just rides fine.

Others may be more sensitive to weight differences than me. Most riders are of course also lighter than me.

early verdict on heavy alu wheels
I think I can say that budget wheels don't ruin your ride, not even your speed. The main downsides are likely in the mind. Any speed difference will be much smaller than you may think.
Just as fast as good light carbon wheels, though? Probably not. The difference is likely so small that it would take elaborate Chung testing to gather any useful data.

Cornering felt particularly good, but that may have been more down to trail conditions being amazing this week. There are some interesting discussions on stiffness versus compliance and the various spoke materials, for cornering performance and rolling resistance, but I can't confidently comment on those matters for these two very different wheelsets.

CUES hubs
The freehub has 24 points of engagement compared to the 54 in the Luther rear hub. I won't pretend like I noticed that difference on the rides. Lovely to have these hubs, setting the bar on quality for fancier hubs to at least match.

cost vs weight
The weight difference to a mid weight carbon rim is so large here, 680 vs 428 grams, it's a reasonable upgrade proposition per gram for a weightweenie. If this exact alu wheelset comes on a Trek 32" Procaliber 9.5, then losing a full kilogram with a €1150 wheelset is mighty appealing. I'd recommend to keep the alu wheelset around if you can afford to, though. It's worth more to you as a second wheelset than sold on the secondary market.

second ride: a bit of a scare
Three days later, 50+ km mostly on lovely forest trails, the wheels were again fine. Invisible, in a good way, just like the carbons have been.
Until suddenly, in a fast grippy concrete corner on a road descend, the front tire folded over quite a bit. That got my attention!
Air pressure didn't seem excessively low, although I had in fact lowered it from that first test ride with the wheels.

downside to alu rims
I've read that aluminium is less suitable to tubeless and now after a third ride with the front wheel, I am seeing little hints for that to be the case. It may be a good idea to keep the alu wheels (if not ridden weekly) on innertubes, especially if peak performance isn't your whole personality.

which wheels do I prefer, aluminium or carbon?
Still the carbons, definitely. I only have XC carbon experience with the Luther wheels which I consider mid-weight, high stiffness.

While the Ryde/Cues alu wheels don't obviously reduce fun nor speed, they also don't bring anything extra. It's just a weight/quality/cost equation where cost was more important.


r/32inchbikes • • 6h ago

Has anyone successfully received and built a 32-inch frame from Chinese manufacturers (Lightcarbon, Tantan, Seraph, etc.)?

Post image
4 Upvotes

I'm looking into getting a 32-inch frame from one of the Chinese manufacturers selling this particular frame mold.

I've come across listings from Lightcarbon, Tantan, Seraph and potentially other sellers offering what appears to be the same frame.

I'm curious if anyone here has actually:

  • Ordered and received one of these frames.
  • Successfully assembled a complete bike using it.
  • Had any issues with frame quality, tolerances, compatibility or missing parts.
  • Actually ridden it and can share some feedback on how it performs.

I'm particularly interested in hearing from people who have gone through the entire process, rather than just seeing product listings or promotional pictures.

Has anyone pulled the trigger on one of these? I'd love to hear which seller you used, how the experience was, and whether you'd recommend it.

I've attached a picture of the frame mold I'm referring to for reference.

Thanks!


r/32inchbikes • • 8h ago

Rim/Wheel advice for a 32" gravel build

3 Upvotes

Planning to equip and race 61mm tires for rough gravel courses in upcoming race season (Silca RCG3 and similar). Width of existing gravel rims and prices vary wildly in weight, aero claims and availability. Aerodynamics of wheel/tire system completely unknown - tire airflow cannot "detach" to a much thinner rim, yet many riders using a "rule of 80" (80% rim width instead of 105% rim width) for tire to rim interface. Any thoughts on the following list of rims, and evidence to support? Newmen seems to have the best compromise out there right now, but unobtanium expensive and also you can't actually buy them. Note: I'm only looking for "what would you build and race 61mm tires with", not recommendations to use a skinnier tire.

Rim / ManufacturerDepthWidth (ext / int)Claimed weightPurchase route
DK Composite G60TL-47-3260 mm47 / 35 mm550 gFactory quote; hooked
9th Wave SandStone SL3252 mm43 / 37 mm480 g€800; backorder; hookless
NTP G30-50-HB50 mm44 / 30 mm520 gFactory samples/inquiry; hollow bead
DeerCycles 32ER 5252 mm40.4 / 32 mm450–490 gOEM quote; hooked
Speeder SC-40GD52TL3252 mm40 / 32 mm480–520 gFactory inquiry; hooked
Venn 440 TCD UL 3244 mm39 / 32 mm400 g$499; made to order; hooked
DeerCycles 32ER 4545 mm40 / 32 mm420–460 gOEM quote; hooked
Speeder SC-40GD45TL3245 mm40 / 32 mm460–500 gFactory inquiry; hooked
EIE A32G50TC36H50 mm*36 / 30 mm480–560 gRetail configurator; hookless
EIE A32G45TC3645 mm36 / 30 mm460–540 gRetail configurator; hooked
Ornan G27-4545 mm33 / 27 mm430–520 gFactory inquiry; hooked or hookless

*EIE's 50 mm model has conflicting specifications: product name says 50 mm, detailed specs say 45 mm.


r/32inchbikes • • 6h ago

32-inch Vs. 29-inch MTB: Which Is Actually Faster? | Real-world Test Against The Clock

Thumbnail
youtu.be
1 Upvotes

r/32inchbikes • • 23h ago

I’m done messing with my Jones LWB 32” for a while

Thumbnail
gallery
17 Upvotes

Took it out on a really lovely ATB route on an extremely unseasonably warm November day. The route had crushed limestone, old school twisty rooty singletrack, blown out fall lines, pavement connectors, champagne gravel, perfectly manicured machine built bermed out singletrack, and just about everything in between. I have it setup 2x2 gearing (36/20 and 34/22), which seem to be the perfect 2 gears for how I ride. It’s just so fast with so much grip and stability.


r/32inchbikes • • 1d ago

Forget the Speed Debate: 32-Inch Wheels Just Make Gravel More Fun - Velo

Thumbnail
gallery
16 Upvotes

r/32inchbikes • • 1d ago

Leovelo Greyhound 32

Post image
12 Upvotes

r/32inchbikes • • 1d ago

The Dark Knight Rises

Thumbnail
gallery
55 Upvotes

The Dark Knight Rises

Sharing information about my very new gravel 32er build.

I’ve only been out once since completing the build but can say I was just blown away by the ride. For my height (195cm), dimensions and flexibility the new wheel standard has a hell of a lot going for it.

Hopefully the following can be useful for others who may be looking to embark on a similar journey :)

 

Few highlights:

1. Custom Ti from XACD in China, Micro Arc Oxidation treatment (black colour)

2. Intend BC Samurai 32er forks adjusted to 80mm travel and 527mm Axle to Crown

3. Carbon wheelset (aliexpress) - 50mm deep, 38mm outer width, 32mm inner, hookless, 28 spokes both wheels, rear 148 x 12, front 110 x 15, Goldix M240 hubs

4. Components a mix of parts from an older build and some new to cater for the newer wheel standard (listed below).

 

Some weights:

  1. Total build 10.9 kg sans pedals but including everything else such as sealant – bang on 24 lbs for those yet to adopt the metric system
  2. Wheel set 1611 grams
  3. Forks ~1580 gm (less than spec as not much of the steerer tube is retained)

 

Manufacturer and the process to design:

I contacted a few manufacturers, including Waltly. Ended up selecting XACD partly based on better upfront comms, good online reviews, and despite a higher cost than other quotes.

I highly recommend ditching bikeCAD and instead using AI to help develop your geometry requirements. Its incredibly useful for all calculations as well as useful feedback on aspects to check and consider.

Process to land on my geo:

- Using 3 other bikes (road, gravel and e-gravel) where my geo had converged over a number of years – I took my position from these.

- Also estimated my forward / rear position to retain a balance I was already comfortable with.

- Used AI to generate geo for a bunch of 32er frames on market (even from just the side photo if you tell it wheel circumference and tyre width it can figure out the rest pretty accurately, including angles and all side on measurements) – used this to consider a bunch of aspects of the build.

I then solved for:

- Tyre clearance in the rear triangle

- Using suspension upfront, considering fork offset and trail

- Chain line needed for the rear hub width and avoiding heel rub (so mtb boost wider chainline was needed)

- Higher ATC due to the suspension forks

- No toe overlap, slightly slacker helped make this work

- Stability and comfort – longer chain stays, slacker HT and slightly higher stack, but retaining my seat height, preferred set back, reach and so forth.

 

Tube radius and widths required some negotiation - XACD thought I was building an MTB rather than a gravel bike… we ended up compromising on a few components to land on a weight vs. strength trade off.

Couple of extra features I added in:

- Additional bracing where the downtube joins the head tube – hoping to strengthen this join for such a short HT

- Ovalised top tube

This is my actual frame being used for a promo shot XACD did before they added the MAO treatment:

https://www.facebook.com/photo/?fbid=1728618989265383

 

Geometry summary:

  1. BB drop               110 mm
  2. Chainstay             470 mm
  3. HTA                   69°
  4. Head tube             110 mm
  5. Fork ATC              527 mm
  6. Fork offset           46 mm
  7. Seat tube C-T         500 mm
  8. Effective STA         73°
  9. Reach                 430 mm
  10. Stack                 693 mm
  11. Front centre          ≈699 mm
  12. Wheelbase             ≈1156 mm

 

The spec for other components:

  1. Wheelset - 50mm deep, 38mm outer width, 32mm inner, hookless, 28 spokes both wheels, rear 148 x 12, front 110 x 15, Goldix M240 hubs, pillar TB2015 spokes – built by the supplier, rims with no spoke holes (no tape needed), hookless
  2. Set up tubeless, Silca 32 x 2.4mm tyres (61mm – larger on bike)
  3. SRAM Ultimate Post mount calipers (oddly these are lighter than the flat mount force calipers I had already)
  4. 180mm Galfer shark brake rotors 2mm thick – plenty of stopping power
  5. SRAM force AXS shifters
  6. SRAM XX1 MTB boost 175mm crankset – slightly wider Q factor but barely noticeable imo, still like this length for me, plenty light and ~53mm chain line
  7. 1x 34 round tooth chainring, (only just enough gearing on a recent ride, I may look at a 32 tooth for bigger steeper trips)
  8. SRAM xx1 eagle 10-50 tooth chainring
  9. SRAM AXS rear derailleur
  10. ENVE 27.2mm seatpost, 25mm set back
  11. ENVE gravel handlebars
  12. Stem from aliexpress – 70mm and minus 17 degrees (i can't go for that negative slope look)
  13. Bunch of Ti parts, bolts, bottle cages etc just to round it out

The ride and performance:

I’ve only been out for one ride. It was a short loop I’ve previously ridden a few times - 62km with ~1350m elevation gain, mix of pavement, cat 2 and 3 gravel, and some single track. The new bike was super fun to cruise on, comfortable, grippy and just felt like it could levitate over washboard and rocky sections. Love the silca tyres, and it reminded me a bit when i first got a 29+ with 3 inch mtb tyres (am a sucker for new bigger wheel standards it seems).

I can easily reach the fork setting to change from lock out to gravel to suspension. I do need to rotate the handlebars slightly as they aren't quite where i want them for full cruising mode in the drops.

Comparing the same route for the new build against a previous gravel bike of mine - older build weighed almost 3kg lighter - for me that is about 3% of total system weight. Outcome from the comparison - ride time was identical, while the measured power, both overall and drilling into many of the strava segments - was ~15% less for the new / heavier bike. Is this a robust comparison – not at all. Different power meters, different dates, likely different conditions, fairly sure my weight is the same, but all sorts of things could obviously vary. But I certainly didn’t feel slower or disadvantaged on the new build and enjoyed so many of its advantages.

Despite the histrionics we are hearing regarding the new wheel standard I am totally sold on 32er for gravel!

Hope this is of interest and useful to others in the community. Peace and love to all 😄


r/32inchbikes • • 1d ago

PYGA, (don’t know how to link from Facebook)

Post image
6 Upvotes

Interesting Sid fork extensions


r/32inchbikes • • 2d ago

32-Inch Gravel Wheels: The Future or the Next 650b? | Velo Podcast

Post image
4 Upvotes

They're covering this topic as much as we do now!

https://velo.outsideonline.com/gravel/gravel-gear/velo-podcast-32-inch-gravel-wheels/

https://youtu.be/_WPp7xxSQQU

If you're a cool appreciative reader/viewer, drop some likes here and there!


r/32inchbikes • • 3d ago

Huhn 32" XC soft tail proto

Post image
34 Upvotes

https://www.instagram.com/p/Df6rz4_DKVs/

Elastomer stem as rear suspension


r/32inchbikes • • 3d ago

Spotted : pictures of 32" bikes Spotted: Trek Shows Off Its Unreleased ProCaliber 32 at NICA Western Regionals - BikeRumor

Thumbnail
gallery
11 Upvotes

r/32inchbikes • • 3d ago

Enigma has produced a 32in version of its Esker titanium gravel bike - Road.cc

Thumbnail
gallery
11 Upvotes

Earlier this year I shortly road a friend's 700c XL Enigma Gravel bike. I was pleasantly surprised by how bloody good a Gravel bike could feel, in comparison with my experience on similar but lower end steel bikes in the mid noughties. I can't wait for the opportunity to try out their approach to 32".

"...and here it is in all its glory, complete with a guest appearance from everyone's favourite little alien.

If you were at Rouleur Live show in London last week, you might have spotted the Esker 32 there, and it’ll feature in the Enigma Bikes show night at BW Cycling, Bristol this evening (Thursday 19th November).

Unless you’ve been living under a rock, you’ll have noticed bikes with 32in wheels popping up all over the place recently. Suggested benefits of the larger wheels include helping bikes roll more easily over rough terrain, maintaining momentum and improving stability – although some people dismiss the whole concept as simply a means of getting you to spend more money.

Of course, you can’t simply fit 32in wheels to a standard 700C bike, so British titanium brand Enigma has produced an Esker 32in gravel bike, made and finished in its Sussex workshop.

Yes, those wheels look big – because they are big – and you can see that Enigma has curved the bottom of the seat tube forward slightly to accommodate the extra size.

We like the top tube graphic incorporating the 32 reference. And who’s that little figure on the down tube? Cool, huh? A standard Enigma Esker frame costs from £3,899. Be good. "

https://www.facebook.com/roadcc/posts/enigma-has-produced-a-32in-version-of-its-esker-titanium-gravel-bike-and-here-it/1577663441055665/


r/32inchbikes • • 3d ago

G32 Superfast : Stoll and Bike Ahead announce Swiss-German 32" Gravel collaboration

Thumbnail
gallery
24 Upvotes

60 mm tire clearance, that's almost amazing! Some 2.4" are labeled 60 mm, some are 61 mm. On wider rims, they may measure around 63-64 m. Let's see how that works out in practice. It's probably for the better that the Stoll people did the design, as Bike Ahead's 32" hardtail was just a 29" frame where the larger rear wheel could rotate in. Only two sizes, that's not very ambitious.

"To celebrate the 10th anniversary of their partnership, Bike Ahead Composites from Germany and Stoll Bikes from Switzerland release the first bike which they developed together: The G32.

While Bike Ahead has been the frame manufacturer for Stoll since the very beginning 10 years ago, the new G32 was designed by Stoll and is manufactured by Bike Ahead. While Stoll was responsible for the geometry, design and ride dynamics, Bike Ahead took care of the carbon technology and production.

According to the two teams, riders will be perfectly integrated into the frame and between the two big wheels. The bike is optimized for speed, thanks to it’s aerodynamics and efficiency. It can also be customized with custom parts, custom handlebar and mounting points for bags.

While the bottom bracket and headtube were optimized for power transfer and steering precision, the rear triangle and seat tube were designed with comfort in mind.

The facts:

- Two sizes: M and L

- Frames will be shipped from March 2027

- For racing and fast tours

- Up to 60 mm tire clearance

- Optional downtube storage

- Mounting points for bags on the upper and lower sides of the top tube

The bike can be ordered at Bike Ahead and at Stoll Bikes.

Made in Germany. Designed in Switzerland."

https://www.instagram.com/p/Df676RuDVPc/

https://www.instagram.com/p/Df671OyjdYU/?img_index=1


r/32inchbikes • • 3d ago

fatscal_fatride : "A small step for 32 inches"

11 Upvotes

r/32inchbikes • • 3d ago

BlackSheep custom: 120/140mm rear travel and clearance for 29x3.0s

10 Upvotes

" theredmantra from twistedspokecbd wanted our first V5 dually with 32 inch wheels. We put the finishing touches on it today, now it's ready for a shakedown in Sedona!

With 120/140mm rear travel and clearance for 29x 3.0s as well, I am sure it will see several configurations to adapt to different possibilities.

Once there are longer travel 32er forks the possibilities will continue to evolve.

The custom Trash Polka inspired finish from u/darkmatterfinishing is so amazing! Oliver really outdid himself in this!

The Nextie rims, u/berdspokes and u/onyxracing make for a very light and responsive wheelset.

If you see Gabe out on the trail make sure to get an up close look at this special build!"

https://www.instagram.com/reels/DfN93PCuqxK/


r/32inchbikes • • 4d ago

Nikas Bikes 32 inch proto

Post image
14 Upvotes

r/32inchbikes • • 3d ago

John Karrasch - 171 cm/5'7", 81 cm/31.9" inseam rider on 32" Gravel. Will it fit?

4 Upvotes

Same fit as Giant Revolt M, what will that take? Just see.

More saddle to bar drop on the 32", actually?
Stem is a bit shorter.

https://www.facebook.com/share/1LFbK5Pjot/
https://www.facebook.com/flexfitbyjohnkarrasch


r/32inchbikes • • 4d ago

32-inch PYGA XC Prototype

Thumbnail
youtube.com
5 Upvotes

r/32inchbikes • • 4d ago

Why XC riders might struggle with 32 inch wheels

4 Upvotes

So many thoughts and sentiments!

Weird take Wednesday! -and no, this won't become a series unless y'all love it. It cost me about an hour to just make this upload. Had to cut down the video.

Good thing he's not ridden one yet, we get the benefit of hearing how he really thinks and feels. We post view of those who are positively anticipating trying 32", and those dreading to have to one day lay eyes on it.
Rob Drew https://www.instagram.com/therobdrew/ at 9:45 says it rode awesome to him, waits for a Pivot offering.

When 29" arrived at the turn of the century, I was commending the riders of the New World for being open minded and just wanting to give a new option ago. So much more positive than Europeans. Has the can-do mentality shifted continents in some ways?

Back then, the industry on the whole just didn't want a change even if it was going to make riding better. The best complaints were "there's not enough 29 inch tires to make it viable".

Now it's "oh, we have to spend money to get a faster bike, it's so baaaaad". As if sports governing bodies have banished smaller wheel sizes. Smashing the half empty glass into a wall.

This year we got countless (really, 50+) 32" carbon rim molds before there was a mainstream bike to buy. Adoption by industry is swift this time, and that's a bad thing according to those who haven't tested and extended their approval yet.

I see a lot of sad faces speaking on this big issue. Like it's a huge social worry of a declining civilization, rather than a bike wheel that gets an extra size option. Psychologists are going to obtain their doctorates studying this behavior one day.

Do bikes perhaps offer a welcome emotional outlet proxy, to avoid talking about the things that actually threaten life as they know it?

(Video cut from 55 to 15 min due to Reddit limitation. Go get the rest at the below link.)
https://www.instagram.com/reels/Df3Uo4hjvps/


r/32inchbikes • • 5d ago

Prophecy, or aging badly? - 29 vs. 32 inches: The Technical Differences and Why You Can’t Escape Superboost

Thumbnail mtb-mag.com
8 Upvotes

We seem to be escaping Superboost just fine?

Most rim makers added more weight from 29" to 32" than just the 10% longer diameter. Not even the aluminium rim makers. By adding some extra bulk to the rim, they overcame the longer distance between spokes, and avoided higher spoke counts.

Where do best practices go from here? Where did Newmen go wrong in their analysis? Or are most brands just tone deaf and doing consumers a disservice, seemingly coming together on Boost for both XC and Gravel 32" bikes?


r/32inchbikes • • 5d ago

32+ tire possibility?

11 Upvotes

Have been holding out a bit to join the 32 club as I have multiple 29+ bikes and love how they ride, but have not yet seen anything about the possibility of 32+ (32”x ~3” tires) as of yet. Has anyone else heard anything or any rumors that this is in development? I’m sure I could convince a frame builder to accommodate, but it doesn’t do much good without tires being available, of course.


r/32inchbikes • • 5d ago

Leon Samita 3D 32

Post image
12 Upvotes

https://youtube.com/shorts/QyYHZ8q-7Zc

A lot going on here. 3D printed titanium. Double flex stays. Split headtube. Free nutcracker included with purchase


r/32inchbikes • • 5d ago

Nordest Arisco Ti Adventure Bike Joins the 32″ Gravel Party For Custom Builds - BikeRumor

Thumbnail
gallery
26 Upvotes

A long wheelbase interpretation of the segment. Quite a bit less extreme than the Salsa Fargo32, though. Nordest is keeping wheelbase and handling a bit closer to traditional gravel/monstercross bikes.

https://bikerumor.com/nordest-arisco-ti-adventure-bike-joins-the-32-gravel-party-for-custom-builds/

The L probably works just fine for XL and XXL riders as well in terms of Reach, even in terms of Stack. Most XXL riders can make a 520 mm seat tube work, although it will be a bit of a flagpost MTB situation (long post = flex = comfort).

With a 1191 mm wheelbase the Nordest Arisco in L is well longer than my XL custom XC bike that was designed for the flatland's winding singletrack. Much longer rear, bit shorter front center. I think the Nordest feel really smooth in the seat and well balanced in terms of front axle load. Main challenge will be lifting the front wheel over obstacles, that's just the reality of longer chainstays. It doesn't affect 2-wheel hops pulling on the pedals, though.

The slightly higher BB is inviting to take it onto rougher (MTB style) trails. At the same that, a long wheelbase does also call for a BB height adjustment to avoid getting too many pedal strikes.

I guess this Nordest like others is made by Waltly, frame and fork? The fork specs do underline it.

So so so cool that Waltly just started making the 444/60 mm offset fork. At the time, absolutely no-one had a dedicated 32" Gravel fork in any material or size.

I've bugged a bunch of Chinese brands about 60 mm forks, but haven't found proof that I also bugged Waltly directly. Seems to have been very sane to go with longer offset, but that's my long standing pet peeve with larger wheels. Who'd have thunk a Chinese company to lead the way?