r/batteries • • 1h ago

Charging an agm battery with LiFePO4 charger

Post image
2 Upvotes

I have a 230ah supercell victron agm leisure battery in my van that should be able to charge at 14.6 volts. Is it safe to charge it with this charger, even for just two hours? It has the typical car battery clamps on one end and standard 230V input.


r/batteries • • 2h ago

Need a replacement battery for my MP3

Thumbnail gallery
2 Upvotes

Hello, I'm looking for a replacement for my Philips GoGear Ariaz 4GB Gen 3.

It's not turning on, not charging and my multimeter says it's got no voltage.

If anyone knows where to get a replacement or how to fix it, it'd be great.


r/batteries • • 5h ago

MH-C9000 charger and batteries with unknown history

1 Upvotes

I refurbish older computers and buy a lot of stuff from junk haulers, scrappers, metal recyclers, etc. Occasionally I get rechargeable AA & AAA batteries. Since I know nothing of their history, how should I charge them using my MH-C9000 charger? Just charge to start or go a bit deeper?


r/batteries • • 7h ago

LiFePO4 batteries in a UPS?

1 Upvotes

I am looking to purchase a UPS to power some of my networking equipment, including a 24-port switch and a modem. Recently, I bought a Wallecube 150 UPS for my Synology NAS, which uses LiFePO4 batteries. Because of their safety and long lifespan, I started looking for a larger UPS that uses the same battery chemistry.

So far, I have only been able to find one model from Goldenmate, which is designed for the US market (110V) and isn't available in Europe. Is anyone familiar with other brands that use LiFePO4 batteries and are available in Europe? Alternatively, is it viable to take a DIY approach by replacing the standard lead-acid batteries in a regular UPS with LiFePO4 drop-in replacements?


r/batteries • • 1d ago

Is this battery still safe to use?

Thumbnail gallery
17 Upvotes

It belongs to my camcorder; it’s still charging and working normally. But the broken case makes me a tad nervous. Is it still usable without worry?


r/batteries • • 14h ago

Can anyone tell me what port this is?

Thumbnail gallery
1 Upvotes

It’s like 2 cm wide and the little thing is about 1 cm wide


r/batteries • • 1d ago

Free internal resistance mobile reference for Li-ion and LiFePO4 cells

Thumbnail gallery
6 Upvotes

Hey folks!

I recently made an update to the Electronics Engineer Helper mobile app that adds an offline database with datasheet verified internal impedances of more than 200 NMC, NCA and LFP cells, so you can quickly find out whether your cell’s internal impedance is within the normal range.

This feature is available for free and without ads on iOS, iPadOS and macOS from the App Store.

The Android version is available on Google Play, with this feature being under development. Let me know if you have an Android device and I will speed up the development.

Hope this reference will help you. 

Please let me know what other chemistries or cell sizes you would like to see added in the comments. 


r/batteries • • 1d ago

Cold battery; charge now or wait?

0 Upvotes

just brought my powered walking gear in from a freezing walk. The battery is still cold and now im watching for condensation like it's a tiny weather system.

My plan is to leave it disconected until it's dry and back inside the charging temperature listed in the manual. I'm not opening it or trying to warm it fast.

Winter users, what's your normal routine?? Do you remove the battery and wait? How do you tell when the middle of the pack has warmed up, not just the outside?


r/batteries • • 1d ago

How to not degrade the battery when "plugged in" for Acer Aspire Go 14 laptop?

1 Upvotes

I see few things:

- acer runs on battery power once 100% charged(Because blue light is seen instead of red light in the power button).

- Get-CimInstance -ClassName Win32_Battery | Select EstimatedChargeRemaining, BatteryStatus

When I type this command with 100% on AC charge, it showed 2 which means on AC power(but unsure about charging or not)....

When I unplugged the type c charger, it showed 1 which means discharging...

I am a poor person and I want to extend the battery life of the laptop as much as possible. What should I do?


r/batteries • • 1d ago

99Wh V-mounts from €130 to €400, what's the catch?

0 Upvotes

Looking for a V-mount battery under 100Wh so I can take it on a plane, to power my camera. Prices are all over the place for what looks like the same 99Wh, so what actually matters? What should I look for and what should I avoid?


r/batteries • • 1d ago

Two power sources operate at same time to charge starter battery in one car. No reason to be worried?

0 Upvotes

Both battery charger as well as car's alternator work in parallel in the car as long as engine cooling system bleeding procedure gets carried out in BMW-cars - (at least) series F and G. These are BMW repair instructions where it gets requested. It is actually an unusual settings - two power sources are aiming to charge starter battery.   I think that alternator and charger will only by an coincident aim to maintain same voltage value.  I also believe that BMW proceeding instructions assume battery smart charger to be in use. If no reason exists to struggle what the result will be, why none exists?


r/batteries • • 1d ago

Battery Drain on New Samsung a36 [Plz read body]

0 Upvotes

I got the phone yesterday and did setup and then today in morning I did like 80 percent 10am then I did customisation and all from good lock and all that then I watched sm yt and playced fc mobile for 1.5 hr by 4 pm battery became only 20% and now also I did 100 full again watched yt and in 1 hr 10 min battery is 90.....

I checked battery health from sysdump and all and it was 100 full and charge cycles was also 0 when I checked yesterday....


r/batteries • • 1d ago

Swollen Power Bank - No fireproof container.

0 Upvotes

I found a power bank tucked away in a box today; it's completely broken from a swollen battery. I've had a look here, but I don't have a metal/fireproof container or sand. I know I need to go to a recycling centre to dispose of it, but can't until tomorrow at the earliest.

It's outside on the concrete at the moment with a metal baking tin on top of it (the best I could do), but worried about it overnight, or however long It'll take me to go over there (an hour's walk; I also work during the times it's open) or if it rains.

What can I do to make sure it's safe over night especially or when raining. Thank you.


r/batteries • • 1d ago

what type of battery is this?

Thumbnail gallery
3 Upvotes

r/batteries • • 1d ago

again battery launches, bringing a new way to repurpose used EV batteries to market.

Thumbnail kickstarter.com
9 Upvotes

r/batteries • • 1d ago

Got a second hand Alcatel pixi 4 - won't boot

2 Upvotes

Hi everyone,

I'm trying to revive an older Alcatel Pixi 4 (7-inch, model 9003X) tablet and could use a second opinion before I buy a replacement cell or do any soldering.

Device & Battery Specs:

* Tablet: Alcatel Pixi 4 (7" / 9003X)

* Original Battery: `TLp025G7` (3.8V, 2600mAh Li-Po) with a 6-wire connector attached to a narrow green BMS/protection board.

* Physical condition: The old pouch cell has a slight crease/twist near one bottom corner, though it does not swell or heat up when plugged in.

What I've Tested So Far:

  1. Charging circuit: With the battery unplugged and the Micro-USB charger connected, the motherboard battery pads read 4.24V, so the charging IC appears to be working.
  2. Battery voltage: The old cell started around 3.29V–3.30V. After ~35+ minutes on the charger, it slowly crept up to 3.37V–3.40V and basically stalled there.
  3. Boot behavior:

    * At ~3.35V, pressing Power briefly flashed the empty battery icon for a fraction of a second and went black.

    * Around 3.40V on the charger, it gets stuck in a continuous boot loop (shows the `alcatel / POWERED BY android` splash screen and resets over and over).

    * Power button clicks cleanly and springs back normally.

My Questions:

  1. Since the cell crept from 3.30V to 3.40V without heating up, is there any realistic chance leaving it on a supervised trickle charge will revive it enough to hold boot load, or is internal resistance too high from age + the corner crease?
  2. Assuming the cell is toast, I found generic 2-wire replacement cells locally (`306075` 3000mAh and `305762` 2500mAh). Any tips or pitfalls to watch out for when cutting the old pouch off the original 6-wire BMS board and soldering a new 2-wire cell onto `B+` and `B-`?
  3. Could anything else on the board cause this exact boot loop if the motherboard outputs 4.24V on the charger?

Thanks in advance for any advice!


r/batteries • • 1d ago

Pretty newbie questions about 1S6P 32700 LiFePo4 pack

Post image
6 Upvotes

I have re-purposed an LED emergency light box that is waterproof enough to work well for my needs and limited knowledge/ability. I really just want a long lasting, LiFePo4 battery pack for powering an ESP32 camera at 5V via USB that can accept charging input from either solar or wall charger at 5V via USB. The box originally came with a 1S2P 32700 LiFePo4 and did just this. It worked well for the LED and seemed much safer and less easily messed up than LiPo. But the original pack needed re-charging far too frequently given the near constant 0.128 amp draw to the camera.

So I purchased 6 new 32700 LiFePo4 cells and put them into a cell holder I could easily wire in parallel. I ran +/- leads attached to the cell holding clips as show with the red (+) and green (-) arrows. Overall, the length of the leads are identical.

As with the original 1S2P pack, the leads attach to a 1S 3.2V 3A LiFePO4 BMS PCM Battery Protection Board (under the black shrink tube) and that board connects to the original circuit card as the original pack did.

Basically, this all works about as expected. When there is no real sun here in the PNW during the winter, the pack needs recharge about ever 6-8 days (much better in the summer months). And I am fairly happy with how the cells charge via USB while inside the box. But after charging until "full" this way, I occasionally open the box, remove the cells, and put them individually into my LittoKala wall charger to see if it "agrees" with the voltage/charge levels.

The pattern I am seeing in the results of these tests makes me wonder... Generally speaking, the 2 cells on the extreme left/right of the cell holder take roughly another 200 maH each until the LittoKala says they are full. Not much difference and within reasonable expectations, I think. However, the 2 cells in the middle of the holder take roughly 10 times that amount: 2000 maH each until the LittoKala says they are full. And I find this difference a bit difficult for me to explain. And I would sure like those extra maH when charging with the cells in the box via USB.

So:

(a) Can someone explain this for a newbie like me who is just dabbling/learning?

(b) Is there some better way to do all of this given the constraints of what I have and need to accomplish?

Thanks for your thoughts. Best!


r/batteries • • 1d ago

Battery health after 1.5 year

Post image
0 Upvotes

r/batteries • • 2d ago

is this safe to use?

Thumbnail gallery
7 Upvotes

my mom just opened this package of batteries and this battery came like this. we’re not using it, but i just wanna know 👀


r/batteries • • 2d ago

Cellmate: just wanted to share something I've been working on

7 Upvotes

I'm fully prepared to be roasted, if this isnt allowed mods, please let me know.

I made a free app that I started working on for myself last year, for monitoring Bluetooth LiFePO4 batteries (LiTime, JBD, JK, Daly) here at the house.

I got tired of opening a different battery app for each brand of battery, so I built my own. It’s called Cellmate.

It’s free in your browser at cellmate.reiners.io (Chrome or Edge, on a laptop or an Android phone). No account, no install. Open it, connect your batteries, and you get:

  • All your batteries on one screen: state of charge, voltage, current, cell voltages, temps and time left to full or empty
  • Batteries grouped into a bank, so a series or parallel setup reads as one battery
  • Charts of the history
  • Charge and discharge switches on supported BMSs, with a confirmation first
  • RIDGID batteries too (read only)

The catch is that a browser only watches while the tab is open. Close it or lock your phone and it stops because chrome will sleep the tab.

That’s why there’s an Android app ($3.99 on Google Play, one time, no subscription). It keeps watching in the background, with the phone in your pocket or sitting in the camper overnight. It also:

  • alerts you to faults and low charge, overcharge, overtemp with the app closed, phone sleeping;
  • keeps recording history the whole time;
  • starts monitoring again by itself after your phone restarts.

I’m the guy who made it, a one-man shop, so if your BMS doesn’t connect or something reads wrong, tell me and I’ll fix it.

But why?

I have:

  • a camper with multiple lithium batteries and solar
  • a battery bank and inverter setup for backup power
  • kayak and boat batteries
  • multiple ridgid batteries with bluetooth
  • too much time on my hands and ADHD

I can feel much more at ease charging batteries in my basement workshop, and I get an alert of any issues, and estimate time to full/empty.

Thanks for checking it out, and let me know if you have any issues at all.

If this isn't allowed I apologize, I didnt add the paid app link to the post, and was only showing off the browser setup mainly because I think it's neato.

Please let me know other battery brands it works with and I'll update the chart, Right now it handles all brands I own.


r/batteries • • 2d ago

Looking to switch to rechargeable AA's for photography flashes and general use. Question about Batteries and Chargers

4 Upvotes

Hi guys, I'm looking to switch to rechargeable AA's, AAA's, and 9-volts for pretty much all of my devices that use them. I'm seeing a lot of older posts talk about the Eneloops. I'm thinking to just get the regular ones and not any of the high output ones. Knowing I'll use them in camera flashes occasionally, is the regular ones still recommended?

For the charger: I happen to have these older chargers here. Some Nitecore single battery charger, a Nitecore I4, and an XTAR VC4S. Are these still considered quality chargers for the Eneloop AA / AAA batteries? I've had these for about 10 years now.


r/batteries • • 1d ago

What marks the end of preheating on a self-heating battery?

1 Upvotes

With winter approaching, I'd like to monitor how the battery transitions from preheating to normal charging. What's the best way to tell when the heating cycle is complete and the cells have started accepting a charge?

I'm using a 12V 300Ah battery with the low-temperature charging function from Vatrer. Its page says heating needs more than 5A of charging input. My proposed setup is a compatible shore charger, solar disconnected and no house loads. An external shunt would measure current entering the pack, so the heater's input would be part of that reading during warmup.

I want to mark the transition from preheating to normal charging. For this type of battery, what reading or status tells you the cells have started charging?


r/batteries • • 2d ago

Battery Analyzers And Software

1 Upvotes

So I have a Tech Blog. Every year around this time someone asks me to review some batteries. This year is no exception.

I had an XTAR VP4 Plus which I just upgraded to a VP4L. I had it for a long time before I ever even used the resistance probes on it.

I then expanded to an FNIRSI HRM-10 which does voltage and internal resistance.

This year because of potential inbound batteries and the fact that I have more money than sense I purchased a SkyRC MC3000 and a ZKETech EBC-A20.

I'm underwhelmed by the software by both. And the ZKETech offering is called EB Tester and my computer says it had a Trojan in it. I figured it probably was a false positive so I spent the next couple hours to prove that it was. I went to everywhere, and every website I knew and every AI and I simply could not qualify that it was safe.

From working for the government I even know a guy in Cyber Security. Not a geek with no socks, but a Big Dog. He ran it for me and came back and his first word to me was , "Bro". I knew where that was headed.

Fortunately an Open Source community has sprung up around both machines. I had ChatGPT get rid of some bugs in one software for the MC3000 which took an hour or two. I'm very happy with it.

Yesterday I spent a lot of time working on one GitHub project for the EBC-A20.

Here's my point. Both machines have been around a while. Both machines I feel are lacking in software support. I know NOTHING about code or coding. Well, not much anyway.

In two days I feel like I have some greatly improved software.

I'm wondering why no one else has done this. Not patting myself on the back because I really did nothing but it is so easy to do I can't believe 100 other people haven't done it.

I even had ChatGPT crunch it down to a .dmg file for MacOS on the EBC-A20. By the way I am not ready to share that. I want to see it successfully charge a dozen or so batteries first before I share.

Anybody else feel like me with some of these more advanced chargers/testers?


r/batteries • • 2d ago

Anyone using those 4-in-1 USB-C charging cables for AA batteries?

0 Upvotes

I'm thinking about getting some USB-C rechargeable AA lithium batteries for home use. They seem pretty convenient since you don't need a separate charger.

The 4-in-1 charging cable looks handy, but I'm a little concerned about having multiple batteries and loose connectors so close together while charging.

Has anyone been using one of these cables for a while? Any safety issues or things to watch out for?