r/functionalprints • • 23h ago

AI Assisted Design (transparency per Rule #8) A toothed hinge for my camera clamp, so it can actually point down

Thumbnail
gallery
20 Upvotes

I sketched the mount and used AI to help model it in OpenSCAD. My first print held the camera at a fixed angle and I still couldn't point it down far enough.

This version has teeth on the hinge. I loosen the side knob, move it a notch and tighten it again. Both screws are printed. The second photo shows how the clamp grips the rail.


r/functionalprints • • 16h ago

AI Assisted Design (transparency per Rule #8) Modular desk organizer: modules lock together from underneath with butterfly keys

Thumbnail gallery
5 Upvotes

r/functionalprints • • 17h ago

Organisation / Storage SodaStream Desk Holder

Post image
5 Upvotes

I designed a simple holder that lets you keep your SodaStream bottle under your desk, freeing up valuable workspace while keeping it within easy reach.

What do you think? Would you find this useful?


r/functionalprints • • 19h ago

Outdoor / Automotive / Bike SW20 cup and phone holder, head unit update

Thumbnail makerworld.com
5 Upvotes

Car from the 90s plus 3D printing results in modern amenities like Android Auto and... a cup holder.


r/functionalprints • • 1d ago

Organisation / Storage Brads and pins organizer

Post image
9 Upvotes

r/functionalprints • • 1d ago

Home / Furniture / Household I made a can stand for my desk: the condensation drips into a little cup instead of onto the desk, it doesn't lift off with the can like a wet coaster does, and it fits slim, sleek and standard cans

Thumbnail
gallery
12 Upvotes

Cold cans on my desk always left a puddle, and coasters didn't fix it. The water still runs off the side, and a wet coaster sticks to the bottom of the can, comes up with it and then drops off at the worst moment. Plenty of designs fix one or two of these things, but I couldn't find one that fixed them all at once, so I made my own.

What it does

  • Catches the condensation. Whatever runs down the can drips into a small cup in the base. The supports stand inside the cup, so water on them ends up there too.
  • Stays on the desk. The can never sits in the water, it rests on small ledges above it, so there's nothing for it to stick to. You lift the can and the stand stays where it is.
  • Fits three sizes. There's a staircase inside: slim cans (53 mm, Red Bull, Boost) drop to the bottom, sleek ones (57.5 mm, Celsius) stop on the first step, standard ones (66 mm, most sodas and beers) on the second.
  • Harder to knock over. Six spokes make a foot 128 mm across. It helps most with tall slim cans.

How it got here

It took a few prints to get the cans to stand properly upright. What made the difference: only 0.5 mm of play on the diameter, steps that slope slightly away from the can so it can't wedge itself down, and ribs on the back of the supports and across the floor so nothing flexes.

Every edge is rounded, because tall thin supports on a desk are exactly the thing you catch your hand on.

Print: Bambu A1, PETG, 0.28 mm layers, no supports, printed solid so water can't get into the part. About 1 h 50 min and 48 g. Free on MakerWorld with the profile: https://makerworld.com/en/models/3652014-no-drip-tip-resistant-multi-size-can-stand#profileId-4190222

If your favourite can doesn't fit, tell me its diameter.


r/functionalprints • • 1d ago

Tool / Jig / Fixture Pipe Connectors

Thumbnail
gallery
32 Upvotes

Hi! This is an older project, but still useful.

Those pipe Connectors are suitable for 25mm pipes, but can be scaled for any dimensions you want.

I made those pretty bulky, so It can sustain some force before it brakes.

https://makerworld.com/models/3344045?appSharePlatform=copy


r/functionalprints • • 1d ago

Tool / Jig / Fixture Paint mixer

Thumbnail
gallery
7 Upvotes

Well, after finding out I can't find this thing in any store from my city, i decided to make it.

If anybody wants to do the same, here's the link.

All details in the description.

https://makerworld.com/models/3395991?appSharePlatform=copy


r/functionalprints • • 1d ago

Organisation / Storage Adjustable Display Deck

Thumbnail
gallery
3 Upvotes

Hi! I made this simple deck for holding different objects on top of your tv or computer monitor, laptop, etc.

It uses just 2 screws, is easy to print and lightweight. Holds a lot of weight and it's adjustable.

Any download helps me buy my dream AMS unit. 🥹

https://makerworld.com/models/2823755?appSharePlatform=copy


r/functionalprints • • 1d ago

Tool / Jig / Fixture Free browser tool: turn any photo into a lithophane (3MF/STL), with a lit preview, text and hand-fan shapes

1 Upvotes

r/functionalprints • • 2d ago

Tool / Jig / Fixture Prototyped a Fish Cleaning Tool

230 Upvotes

Now drinking beer while fishing is essential. Any suggestions for improvement?


r/functionalprints • • 1d ago

Home / Furniture / Household Coffee mug holder

Thumbnail
gallery
1 Upvotes

The vibration from my Coffee Machine will never push my mug away again. Took me 40 minutes to design and print.


r/functionalprints • • 1d ago

Tool / Jig / Fixture 3D printed Screwdriver bit holder.

Thumbnail
gallery
2 Upvotes

Hi! Still learning to 3D model stuff. I've made this screwdriver/drill bit holder.

Useful for small workspaces.

At least for me, it's very useful. If you want to give it a try:

https://makerworld.com/models/3641240?appSharePlatform=copy

The final model is slightly modified to be easier to print, and also has a built in main part stand, rather than a separate part, I need to print and retake the photos after my filament is delivered.

Every download will help me get closer to my dream, a AMS unit 🥹


r/functionalprints • • 1d ago

Electronics / Mounts / Enclosures Temperature sensor enclosure for Bambu P1S

Thumbnail
gallery
1 Upvotes

Hi! I made this simple temp sensor holder for a generic module. Simple, easy to print and useful for printing abs and other materials sensible to heat

https://makerworld.com/models/2792867?appSharePlatform=copy


r/functionalprints • • 2d ago

Tool / Jig / Fixture Garage door remote mount, USB-C

Thumbnail gallery
6 Upvotes

r/functionalprints • • 2d ago

Organisation / Storage I made a free rugged box generator that sizes the box from a tracing of your stuff, picks the print orientation for your bed and bakes in the supports. Runs in the browser, live 3D preview

Thumbnail
gallery
8 Upvotes

Most parametric boxes I found are OpenSCAD or CAD models with a customizer: you change a number, wait for it to render, export, open the slicer and find out the lid doesn't fit your bed or the hinge is too tight for your printer. I wanted something that handles all that for me, so I wrote a generator.
What's different from other parametric box generators:
Live 3D preview. It updates while you drag the sliders (about 0.1 s), with assembled, exploded and print plate views, an opening animation and a section cut
Box sized from what you store. Drop in SVG tracings of your items (1:1 in mm) and it packs them in the smallest space, then cuts pockets and finger notches into an insert
It decides how each part prints. Flat if it fits, diagonal with easy-peel anti-warp ears if not, or tilted with a contact bevel, fins and supports already in the STL
Clearance test for your printer. Small test prints for each joint in the orientation it actually prints, and the result is saved as a profile for your printer and material
Compartments with hinged covers, in the base, the lid or both, with a snap or a magnet latch. You enter your magnet size, it suggests how many to use (or you choose) and makes press-fit pockets with crush ribs
Export includes a README for that specific box: slicer settings, assembly steps and what to buy or cut (magnets, gasket length, filament for pins)
And the usual stuff:
Hinges and self-locking latches, scaled automatically from 20 to 380 mm, no screws or hardware
TPU gasket, a groove for 1.75 mm TPU filament (no gasket to print), double labyrinth or a simple tongue
Stackable, Gridfinity, octagon corners, lid patterns and your logo from SVG
Material saving mode with a ribbed wall that keeps the stiffness
Undo/redo, dark mode, everything prints without supports
No install and nothing is uploaded: it runs in your browser, or you can download a single HTML file and use it offline.
Try it: https://parra0713.github.io/parametric-rugged-box/
Code (MIT): https://github.com/Parra0713/parametric-rugged-box
Heads up: the interface is in Spanish for now. If people are interested I'll add English.
The newest stuff (magnet latches, compartments in the base) I haven't fully printed yet, so feedback and bug reports are very welcome.


r/functionalprints • • 2d ago

Organisation / Storage Gridfinity hex bit holders and trays

Thumbnail gallery
5 Upvotes

I recently published a series of Gridfinity hex bit holders and trays that I feel are versatile, scalable, simple, and have a nice aesthetic. I would love to get some feedback on them. THIS IS THE LINK.

One refinement I have in mind is wider spacing for the vertical holders to be more accommodating for larger fingers.

The initial idea was gradually taller surfaces to better accommodate both short and long bits, and also a horizontal tray to accommodate double-end and very long bits. From there I thought some modular scalability would be useful. I ended up with a couple curved surface holder blocks, and a slanted planar block. Then added smaller curved and planar expansion modules that mate flush.

(The Pac Man ghost was an older design exercise that is published separately HERE.)


r/functionalprints • • 2d ago

Tool / Jig / Fixture I designed a small Aqara E1 / G3 mount for IKEA SKÅDIS

Thumbnail
gallery
2 Upvotes

I wanted to mount my Aqara camera directly to my IKEA SKÅDIS board without drilling holes or using additional hardware.
So I designed this simple adapter.
**Features:**
Compatible with Aqara E1 & G3
Fits IKEA SKÅDIS
Tool-free installation
Uses the original Aqara ceiling mount
Clean cable routing
\~13 g of PLA
Less than 1 hour print time
No supports needed
The whole idea was to keep it as small and simple as possible while still being sturdy enough for the camera.
I made the model available for free on MakerWorld if anyone has a similar setup.
Would love to hear what you think or if you have ideas for improving it!

https://makerworld.com/models/3408331?appSharePlatform=copy


r/functionalprints • • 3d ago

Home / Furniture / Household I designed a 3D-printed push-to-open click latch mechanism using a pen spring - I’ve already sacrificed every clicky pen in my house for 3D prints, any left in yours?

Thumbnail gallery
95 Upvotes

r/functionalprints • • 3d ago

Electronics / Mounts / Enclosures I Made this JetEngine nozzle for my Wolfbox MF200 - a Venturi nozzle that pulls in room air. Ran it through CFD Simulation before printing

Thumbnail
gallery
39 Upvotes

Edit, 22 Nov: I got one thing wrong. I said this moves "more air". That compared each nozzle at its own tip, and the tips are 7 cm apart, so it wasn't fair. At the same distance from the duster it's a tighter, faster jet, not more air. Thanks to everyone who called it out. The pictures above are the old ones. The model page has the corrected pictures and numbers.

I wanted a better nozzle for my Wolfbox MF200 and ended up designing one.

It's two parts. The core clicks into the duster and squeezes the fan's air into a 19.5 mm jet. The shroud twists onto the core, pulls some room air in through the 8 vanes at the back, and keeps the jet from spreading out through a 29 mm tube. So it still has punch when you can't get right up close.

I ran it in CFD before printing (OpenFOAM, same fan curve every run): core on its own against core + shroud, at the same distance from the duster.

  • 74 m/s vs 51 m/s on the centre line at 25 cm (+45%)
  • 54 m/s vs 39 m/s at 30 cm
  • push 238 g vs 232 g, so about the same
  • a bit less back-pressure on the fan with the shroud on

It doesn't add power. It's an ejector, so all it changes is how the jet mixes with room air. A bare jet pulls in more air on its way, the shroud keeps it together.

On my kitchen scale the real print pushes 260 g. The stock nozzle does 235 g.

A few details:

  • 1° taper on the mount so it presses in and seals, plus the bayonet click
  • The shroud locks with a 30° twist. It clicks shut and doesn't rattle
  • One plate. Core prints bayonet end down with supports only under the centre hub, shroud stands on its tip with no supports
  • Profiles for Bambu printers at 0.16 mm. Mine's gray ABS on a P1S, PLA works too

Model: https://makerworld.com/en/models/3637893 MF50 version: https://makerworld.com/en/models/3659016

Video of it on a pile of leaves is in the comments. Ask me anything about the CFD or the design. If you print one, show me.


r/functionalprints • • 3d ago

Organisation / Storage Parametric, stackable screw organizers with a spot for NIIMBOT labels

Thumbnail gallery
16 Upvotes

r/functionalprints • • 3d ago

Home / Furniture / Household I made a stand out of flat links with hinges that stay locked until you squeeze them. Everything is printed, even the springs.

Thumbnail gallery
11 Upvotes

r/functionalprints • • 3d ago

Home / Furniture / Household Shark WV200 & WV251 Cordless Handheld Vacuum Nozzles

Thumbnail gallery
12 Upvotes

r/functionalprints • • 3d ago

Organisation / Storage Creé una aplicación gratuita para navegador que genera cajas resistentes del tamaño que necesites para almacenar.

Thumbnail reddit.com
1 Upvotes