r/hackintosh • • 22d ago

New Mods, Rules Update, and RFC

115 Upvotes

Hey guys,

We've had a lot of developments in the community lately, especially in the past month. We've been internally discussing how we can best position the subreddit to promote development while also protecting the sub from malware and bait. We have three particular things to share with you.

0. New Mods!

With the existing moderators becoming busier lately, it has been hard keeping up with the renewed activity in the subreddit. We greatly appreciate the effort put in by the community to try things previously thought impossible, and to keep up with the increased posts, we have two new moderators - u/SkinnyHedgehog and u/yuichiro__ - Say hi!

1. AI-generated projects

There have been divided opinions on the topic of tools and drivers written almost or completely using AI. While it has accelerated development, there are some things we feel the community will benefit from being aware of.

As a case study for (almost-completely) AI-generated code, we have the new Nvidia driver from NullMoth.

It has gathered a lot of (very warranted) attention. Writing code that runs close to the hardware requires that you hold yourself to a high standard when designing the architecture and writing code. The tool released by NullMoth is a combination of several things packaged as one. It is a graphics driver, it is an Apple logo modifier (to a custom moth-themed Apple logo), an EFI creator, and a log aggregator and crash reporter (the last few things as part of the 1401 companion app). Apart from the subjective opinions surrounding the developer of an open community advertising themselves through invasive system modifications (which no established tool has done before), it presents innumerable attack surfaces and unchecked vulnerabilities. Link to Vulnerability Report

If you have this driver loaded on your computer, an attacker could very easily gain access to your entire computer, including all your files, your apps, and browser history.

Some of the reported vulnerabilities are things that no sane developer would write, provided they had decent systems and programming knowledge. While they are now patched, there is no guarantee that this driver is free from any more exploits.

An unfortunate reality surrounding vibe-coded software is that the Dunning-Kruger Effect is more prevalent among the developer community than ever, and what may look like good code to the untrained eye may in fact not be so.

To give end users an idea of the potential risks associated with AI-assisted development, we have decided to implement the following changes.

  1. All posts that introduce or exhibit new software must include the DEV flair and must include source code in the post.
  2. They must also disclose the extent of AI use. Whether it was completely AI-written, used for minimal autofill-esque tasks, or not used at all.

To keep yourself safe from potentially unsafe code and malware, we recommend that people with the relevant knowledge audit the source code, report suspicious software to us, and leave a comment letting others know.

2. iOS ports and other non-macOS in this subreddit

Back when hackintoshing first started, the only Apple software that could be run on other devices was Mac OS X. It has remained this way until a few weeks ago. Recently, there have been developments surrounding iOS being ported to non-Apple mobile phones as well. We have gotten reports on almost all such posts, as them not belonging to this subreddit.

We'd like to put this to a vote. Would you rather have the description of a hackintosh as "Apple software running on non-Apple hardware", or keep r/hackintosh exclusive to only macOS? We look forward to your comments.


r/hackintosh • • Jun 09 '25 This

ANNOUNCEMENT Next Stop: macOS 26 Tahoe

220 Upvotes

Hackintoshing lives for another year! macOS Tahoe will be the FINAL release for Intel Macs, as stated during the Platforms State of the Union presentation. It's been a good ride.

Officially supported Intel models:

  • MacBook Pro 16-inch (2019)
  • Mac Pro (2019)
  • MacBook Pro 13-inch, Four Thunderbolt 3 Ports (2020)
  • iMac (2020)

Hello I am a Year Number Lover But What Does This Mean

All graphics that worked in Sequoia should work in Tahoe.

OCLP

Wait for an official announcement. If you post about OCLP before that I am going to send Tim Apple to remove every Mac from your house.

Can I emulate ARM macOS 26 on x86?

No.

Can I run ARM macOS 26 on a Raspberry Pi?

No.

Can I have Apple Intelligence on Intel please I need to write a dissertation in 15 minutes

No.

Does it boot on Intel Hackintoshes now?

Yes, with OpenCore 1.0.5.

Make sure to upgrade all of your kexts to their latest versions.

Known Issues as of Beta 2

  • Race condition with VoodooPS2 and VoodooI2C, so on some boots they don't initialize properly
  • AppleALC is broken because AppleHDA was removed from Tahoe. Use HDMI/DP audio for the time being.
  • WhateverGreen is bugged on AMD cards, so you can't use boot arguments like agdpmod=pikera. You are affected by this if you get a kernel panic with AMDSupport mentioned.
  • IntelBTPatcher causes kernel panics
  • IntelMausi may not work correctly with certain Intel ethernet chipsets

r/hackintosh • • 7h ago

SUCCESS Tahoe 26.7.3 in i5 HD530, without OCLP

Post image
44 Upvotes

Hi everyone, I’ve finally managed to set up the PC for daily use.

The hardware is an Esprimo D556 with an i5-6500, 16 GB of RAM, and a 500 GB SSD, set up in a dual-boot configuration with Windows 11.

It wasn’t straightforward, but fortunately, the hardware provided a good foundation.

Running macOS 26.7.3 without OCLP; SIP and AMFI are enabled, and no patches were required thanks to Kaby Lake spoofing. OTA updates also work, using the iBridged kext.

Metal 3 is supported, and both iMessage and FaceTime are functional—though getting them to work took quite a while.

The monitor is a Dell P2418HZ, connected via DisplayPort. Audio is routed through a USB hub and works perfectly.

Working features: Ethernet (RTL8111), FaceTime, iMessage, phone integration, AirPlay, and iCloud synchronization.

Non-functional: DisplayPort audio, Wi-Fi (there is currently no Wi-Fi card installed in the PC). With an Apple Music subscription, there is no sound when streaming, though audio works fine for downloaded tracks—likely due to DRM.

Known issues:

Waking from sleep causes a kernel panic—even with UTB Map enabled—as does switching from Windows. This is likely due to a CPU ID leak; the kernel panic report suggests that, during the early stages of the boot process, the OS sees the native, unmasked CPU ID.

SMBIOS: 20,1; SecureBootModel: j185; UpdateSMBIOSMode: Custom (for Windows dual-boot).


r/hackintosh • • 28m ago

SUCCESS School laptop hackintosh (Dell Pro 14 PC14350)

Thumbnail
gallery
7 Upvotes

So this is my school laptop and i thought at a good 3 am "what if i hackintosh it" and now here we are, i currently have it installed on a usb (i need to back some things up and then i will dualboot) but it works amazing, i have no complaints

SPECS:

Intel Core 3 100u

8gb DDR5

256GB ssd (Installed on a 64gb usb)


r/hackintosh • • 15h ago Bravo

DEV hackintosh is BACK: macOS 27 with stela and anathema, hackintosh is BACK!!

96 Upvotes
using stela, would be insanely slow (took 4 hours to boot without anathema)
dual monitors working

true dat macos 27 on my rizzen 5 5500 + 3050.

Stela, created by developer Tyler Smith, and Anathema, created by me
FULLY coded with AI, but the code was understood, and not blindly asking claude to "Fix it", like nullmoths driver. (DO NOT ARGUE WITH ME BECAUSE I SAID THIS, I QUOTED THIS FROM AMD OSX)

Stela on this PC: it translates live, and it's slow. Opening Safari took 8 to 10 minutes. By my measurements it's instruction-fetch bound, and compiling takes 16 to 37% of the time while warming up.

Stela Speed: 8-10 minutes to open Safari

My estimate with Anathama: Safari opening should take right bout 1-2min 15-45s

Anathama's PART: I started my own project, Anathema. It isn't a Stela fork. I looked at how Stela works for ideas, but the code is mine. It is a translator plus a virtual machine plus a UEFI loader, aiming to boot arm64 macOS natively on x86. the macOS 27.2 VM kernel boots under my translator on Linux. It gets through IOKit startup, finds a virtual disk, and mounts the restore ramdisk as its root filesystem. Then it tries to start launchd and fails with an exec error. That's where I'm at.

Now the reason I am posting this is because I'd like community/developer advice on how to work on what doesn't work yet, which is:

- Apple's real macOS 27.2 kernel boots through my translator, all the way through IOKit.

- It finds a virtual disk and mounts the restore image as its root filesystem.

- It then tries to start launchd and fails with an exec error. That's the current bug.

https://github.com/riftaway7-code/anathema, It contains no Apple files.

Looking for people who want to help me with this project. Please contact me on discord, @ provided in reddit DMS


r/hackintosh • • 7h ago

DEV AWDL Continuity Camera, Source code release for Intel AX200

18 Upvotes

I've got the CC stable, streams at 30~60 fps, smooth on Sequoia, I've not tested this in any other macos builds or cards.

Feel free to test and adopt changes. Please ensure I get credited for the work :)

Faster on an AX200: 0.6.0-beta.4 to beta.6

Measured on an AX200 with macOS Sequoia 15.8.2 and an iPhone, 120 s sends, Wi-Fi connected the whole time. These are single machines and single runs; the iPhone's own channel plan changes the result a lot.

Result
Mac → iPhone, plain setupAbout 164 Mbit/s with 99.4 % of aggregated frames acknowledged (it was 10 to 13 Mbit/s). The iPhone's Block Ack answers were acknowledged on the air but never handed to the driver when the listener's channel is the Wi-Fi station's; the driver now opens the receive window for them (#22, #24)
Mac → iPhone, slot hopping (experimental)Means of 115.8, 83.3 and 151.9 Mbit/s over three runs, peak 238.7, no disassociation. The listener's own radio context follows the iPhone between channels 149 and 161, so it is present in about 15 of 16 slots instead of 8. Needs -itlawdlcoexmulti -itlawdloverlap80 -itlawdlslothop, see BOOT-FLAGS
Rates the firmware uses97.6 % of the aggregated batches at 80 MHz, 98.8 % with two streams, 63.5 % at VHT MCS 9 (tools/diag/tx_rates.py): the speed is limited by how long the iPhone is on our channel, not by the rate
Continuity CameraThe iPhone stays on the Wi-Fi channel for all 16 slots. Frame loss is 2.1 % with the listener in the station's own binding, against 10.4 % when it had a radio context of its own on that channel (the firmware time-slices the two around the access point's beacons). With -itlawdlcoexmulti the listener now joins the station's binding in that case
Long sendsThe access point could disassociate the station during a 2.7 GB send (reason 34, frames to the station not acknowledged). The power-save data timeouts are 100 ms now, as in Linux's iwlwifi, and three such sends in a row had none

That's all

Builds at : https://github.com/wh0ami7/ForbiddenItlwm/tags

AI used: Yes, most of the logic is tested and adopted.


r/hackintosh • • 52m ago

SUCCESS iMAC G4 build finished! this was a long one!

4 Upvotes

https://imgur.com/gallery/imac-sleeper-build-UUrxatb

so i thought id share, not sure what place to put this but this build took me most of the year.   i got a couple iMACs for free and got a crazy idea to put something modern into one of them.  in the end i wound up with a samsung panel, i5 intel, and a radeon GPU.

some of you might ask why not a mac mini? well at the time there was not good Egpu support and i wanted to game, also EVERYONE has alrady done that so... i took a different route.  at first i thought a micro or mini itx system and that would actually fit! there were some boards from asrock where id be able to drop a off teh shelf setup in there.  so why not?  the dome.

as it turns out, the dome proved to be a surprising (/s) design constraint.  my square area reduced drasticly as i went up so i was unable to raise the itx board above a video card OR put a card over the board.  i did find some low profile cards that could fit but their performance was so poor that a moden intel igpu would have been about the same.  i wasnt willing to go that route....

with out any idea of what fits where, i started looking at physical sizes of things and cutting out cardboard. ca gluing templates to see what might fit!  this actually worked very well but it was hard to find the physical specs. newegg had a good sort by but as it happens, thats only length of a card, not height or thickness so it was into each products spec page and trial and error....

i think i started by sourcing a replacement panel bezel/housing. my imacs were 15" models and i wanted a 17 wide. they are hard to find for a price but i came across a ebay store that turns old macs into art work. he makes real lamps out of these guys and had a warehouse FULL of parts. so i got a full, complete top assembly minus the LED panel.  however go figure.... its TOTALLY different from the 15. screw holes, cables, thickness, mounting, all ofit... none of it fit!   it wasnt hard to drill new hols after making a jig, i tig welded up the old holes and got it together.

at this point i should mention, i started this in febuary i think? when i got the two systems. it is now november LOL.  once id started, i knew id finish, i just had no idea what hte final build would be but i wanted it to NOT be what everone else had done.

quite a bit of amazon, facebook market, and ebay time while i looked for a 'computer' as now id decided a NUC was my only choice. what i quickly ran into was PCIE lane issues.  i needed wifi, a m.2 that was 4.0 spec to run the GPU and i still needed a NVME or some kind of non 3.5 drive. even if i pulled the 3.5 appart i dont think i could have fit that in there.  this landed me on a single height intel NUC i5/i7. in benchmarks there was a less than 10% difference in performance between teh two but there is a boosted power/thermal budget on the i7 and the i5 with tweaked boost settings allowed better performance than the i7 so... i went i5.   the other nice thing was a m.2 for wifi, and a m.2 bkey sata, AND a m.2 4.0x4 that ran to the CPU die and not a controller.  it came iwth 8gb of ram but that was a cheap upgrade. (i actually run into issues with only 16 but idk what to do about that yet).  a bonus was this system had a 4 pin internal 12v PSU plug so that made life easier, no power brick.

once i had that, it was down to the PSU, GPU, and wiring.  id setteled on a 6600/7600xt radeon from power cooler. a lack of hackintosh support for the 7XXX put me on the 6 and its about the same speed. also takes a good OC. but it HAD to be the power cooler red devil as its the only one that would fit!  people complained about tyhe tiny crapy heatsink but thats exactly what i needed!

while i waited i started autocad and 3d printed a bunch of prototypes for the base, mounting, ports, the motherboard tray. fan shrouds, air direction fins and bevels. i bought some small 1.5-3mm nutserts so i coudl screw everything in. just melted it all in place and some bits got ca glue instead of reprinting things.  the I/O was a challenge, at each step of this - i acomplished one task and created 3 more to overcome. in the end i had to mount things and sand down PCB for various ports. each one got a nutsert, 3d printed tabbed holder or some kind of bonding to other parts. i reused the factory power plug and factory holes so the OG case is not modded, just reprovisioned.

it was important to me that from the outside, you would not know its a sleeper or hackintosh. to that end i had to fit EVERYTHING inside. the PSU i found took a couple months. a meanwell for medical uses JUST fit into the allowed space and it had a 600w transient support which works perfect. my total W budget was 325 and i average far below that, even when gaming. still, alwasy good to have more than less. a simple printed box for it with some lattice work for air flow seems to work quite well. i again printed an angle plate to the bottom to hold the whole thing up on its own and screw down with in teh system.

on the bench i found the first lCD panel i bought didnt work. no idea what hte cause was so weeks of testing on that before i bought antoehr panel from another seller. then it just worked.... finding that samsung panel took a good coupel weeks as these screens are not common in monitors. laptops yes but even then, only a few models.  i happened to find a pdf schematic for the panel tho so i had all its specs and pinouts which turned out to be needed as i had to make my own LVDS cables.  about 70cm of them in total to go from screen to under the mac dome. the LVDS control board fit under there where the OG ram was nearly perfectly. i was able to print some hold downs and the factory bottom plate even fit.  i printed a super thin piece to prevent shorting just in case.  also on the screen are the LED for power and the mic, both of which i wired down and was able to use.  at first id wanted to run HDMI so thats what i did. but then discovered my LVDS would not fit in the panel housing so.... had to redo all the wires to add more for the 30 pin, power, backlight, and mic/led. about 40 wires in total.

the fan was a noctua at the top, that was easy and a 3d printed dome top and fan grill kept the wires where htey needed to be and helped direct air flow. id hoped that was enough to pull air up through the openings (which i printed into the base plate) but now tha ti had to move all my stuff around and tilt/stack instead of keeping things to the side like i thought i could.... the GPU was overheating with out fans. not suprising i suppose....   i picked up a 40mm noctua and printed a shroud for it to blas from one side to the other of the gpu heatsink. that gets directed up by some fins and pulled out by the top fan. some luvers help induct more air from around the cool side of the gpu as well. this works well as its only in synthetic testing that i hit thermal limits.

bench testing with everything mocked up worked well. fedora booted first try with the m.2 to pcie adapater. id expected this as i use these adapters on my NAS with out issue. however it needed a 5v power feed that i did not have. i used a buck converter i had laying around to generate this. i had researched cards quite a bit and found a neglidgable performance decrease on x4 vs x16 for this card (4.0 anyway). i also needed radeon as at the time no one had vibe coded a nvidida gpu for mac os driver.

the assembly was decent. printed a plate to hold GPU one side and LVDS/backlight psu on the other. added a mount to the NUC shroud to screw to the gpu heatsink, screwed the psu and gpu to the large plate i made for the base. i used factory screws to hold the base plate down and im able to tip it all upside down iwth nothing moving.  i played aroudn with HDMI cables from GPU to lvds but in the end i had to aliexpress a ribbon cable for this as nothing else fit properly. i only had to move things a tiny bit as most of my measurments worked out.

hte hackintosh install was a challenge. lots of problems mapping things and getting stuff to boot AND i was way out of date on bios. like .50 vs .80  however after updaing my DGPU no longer worked.... only the igpu. i also got lots of ram issues and errors, everything became unstable. several weeks of flashing back but nothing worked. there was a hard lock on flashing back more than like 12 versions but i wanted to go back 20 versions or more. what i had to do was desolder the cmos and replace it to get my older bios back. after this, my ram errors went away and my DGPU started acting as primary again.

a constant issue i had was signaling for the main screen. the 60cm lvds cable was just at its limit. the best i was able to get was some ferrite rings and insulation (not htat i could fit much in that arm) but this got things mostly stable. i get a bit of flicker when screens change but otherwise its stable. so for now thats good enough until i work out a better fix.

i wanted internal speakers as well as i wanted the mack gong and for everyting to be all in one. a small 15w class d 12v amp that i wired into the audio output of the lvds board. i also wired this board to the 3.5 mic/speaker output i made. all wiring is a one off, twisted and routed around the edge and under the video card.

I CANT EXPRESS JUST HOW TIGHT EVERYTHIGN IS IN HERE

fedora 44 loaded just fine, dual boot with sequoia. that setup was pretty easy but the macos took me a good month and a half with help from the hackintosh discord.

3d printer again for templates and i got 2 small speakers off parts express by peerless. wired them in stereo and printed a case to mount on top of the PSU. this plays audio through the plastic cd rom cover that i glued in. with a bit of easy eq in software they sound decent and have some low end.

it was at this point i fitted things together and found they actually FIT!  the whole dome went down on it all. i used some USB and TB extenders for my external ports. directly soldered cat5 to the new port i bought, cut it down, mounted it, and rj45 end into the NUC. it works a treat.  the DP is also and extension but its a ribbon on one end with a 90 built in. JUST fits into the card.  also used fuses and some RC car plugs for the 110v psu input

i had a problem i could nto shake tho.... it did not bong when i turned it on. how????    this is where i foudn a mini mp3 player about the size of a micro sd card. i paired this with an arduino nano i had laying aorund. its set to check the 5v refrence pin on the power headder of the NUC, then sense power button pulling the 2 pin low for more than .5 seconds but less than 2.5 seconds, and then rx/tx to the mp3 player which sends pre-amp to the 15w amp for the startup bong. it does NOT bong if you hold down to shut off OR if you press it for sleep when the system is already on. i got the sound off YT and chose the performa era of bong. this took about a week to get working

i had that second black screen id been using but wanted something period correct. i found a cinema display on marketplace for free. no ide if it worked.  i used magic eraser and dawn to clean the outside, retro bright on the cables, and painted the bezel with pebble grey. in the end it worked out well and looks nearly new again.  im waiting on a dvi to DP cable later this week to get it plugge din but i tested it on my G4 QS and it does work. the ADC to DVI to miniDP to DP did not work tho.

i may add to this or if you have questions ig. i think this is mostly everything.


r/hackintosh • • 13h ago

SUCCESS MacOS Mavericks en mi MSI

Post image
24 Upvotes

termine de instalar macos mavericks en mi msia6430
anda muy bien en esta pc, y con los arreglos de mavericks forever estoy pudiendo publicar este post directamente desde safari

originalmente iba a instalarle macos montain lion para que haga juego con mi iphone 5, pero prefiero que amenos la mayoría de cosas se puedan usar


r/hackintosh • • 14h ago

INFO/GUIDE [Release] IntelSpeedShiftEPPP – Direct Intel HWP EPP control kext (unlocking full 4.40 GHz stock boost on spoofed Alder Lake)

14 Upvotes

I built a lightweight open-source kext to directly control Intel Speed Shift Energy Performance Preference (EPP) via IA32_HWP_REQUEST (0x774) on macOS.

Designed for spoofed 12th Gen+ Intel setups (tested on i5-12450HX, MacBookPro16,4 SMBIOS, macOS Tahoe 26.7.1) where X86PlatformPlugin and CPUFriend frequency vectors don't always tune HWP registers properly for single-core boost or idle package power.

GitHub: https://github.com/xnpty/IntelSpeedShiftEPP

Feedback and powermetrics logs on other Intel generations are welcome.


r/hackintosh • • 1m ago

HELP Dell Latitude 5310 (Comet Lake) + Tahoe: lid close powers off instead of sleeping.

1 Upvotes

Hey all, I've got macOS Tahoe running on a Dell Latitude 5310 and almost everything works (graphics, audio, Wi-Fi, Bluetooth, I2C touchpad, battery). The one thing left is sleep.

Problem: When I close the lid, the laptop fully shuts down. When I open it, it cold boots back to the OpenCore picker, so I lose my session every time.

Hardware

Dell Latitude 5310, BIOS 1.34.0
i5-10310U (Comet Lake-U), UHD 620 (device-id 9B41, spoofed)
Realtek ALC295, Intel AX201 Wi-Fi/BT, I219-LM Ethernet
Micron 2450 NVMe (DRAM-less), I2C touchpad (Alps)

Setup

OpenCore, SMBIOS MacBookPro16,3
Kexts: Lilu, VirtualSMC (+ plugins), WhateverGreen, AppleALC, VoodooI2C/HID, NVMeFix, RestrictEvents, USBToolBox + custom map, IntelBluetoothFirmware, IntelBTPatcher, BlueToolFixup, ForbiddenItlwm/AirportItlwm
SSDTs: PLUG, EC, USBX, RTCAWAC, SBUS, MCHC, PNLF, ALSD, GPI0, XOSI, USB-Reset

What I found

I dumped my ACPI tables with SSDTTime/SysReport. My DSDT only defines _S0, _S4 and _S5. There's no _S3 at all. Dell's own spec sheet for the 5310 also lists Modern Standby (S0ix), S4 and S5, but no S3. So it looks like macOS asks for S3, the firmware can't do it, and the machine powers off.

Any solutions or suggestions?


r/hackintosh • • 4h ago

DISCUSSION Hey everyone! It's been a hot minute but I just dropped my new repo for the Intel version of the Lenovo ThinkPad T14 G1! The repo contains files for both macOS Ventura (as it is the most fleshed out) and macOS Sequoia (it's stable but there are still some missing features)! Check it out! 😎🔥🥋🎧

Thumbnail github.com
2 Upvotes

r/hackintosh • • 2h ago

HELP Hackintosh recommendations for Latitude 5490?

1 Upvotes

I been trying to follow hackintosh tutorials online but so far I’ve gotten nowhere with it.


r/hackintosh • • 2h ago

HELP DiskUtility

0 Upvotes

I have NVMe ssd and i cannot find it in disk utility


r/hackintosh • • 22h ago

SUCCESS Finally got my Hackintosh running! macOS Sequoia 15.8.3 on Ryzen 5 3600 + 2060.

Post image
37 Upvotes

My PC specs:
CPU: AMD Ryzen 5 3600 (6-Core)
GPU: NVIDIA GeForce 2060 6GB
RAM: 16GB DDR4 3200MHz
Motherboard: MSI B450 Gaming Pro Carbon AC

What’s working:
- Onboard Wi-Fi and Bluetooth work perfectly.
- Ethernet works.
- GPU works, thanks to the NullMoth NVIDIA drivers!

I spent 3 days trying to create an EFI. I followed guides, tried existing GitHub EFIs, user kexts, and different configurations, but nothing worked so far.

Then today, I tried the NullMoth macOS installer, and with just a few clicks, it created a bootable USB. And guess what? It booted successfully on the very first attempt! That honestly blew my mind.

Initially, macOS showed only 8MB of GPU memory, but after installing the NullMoth NVIDIA drivers, it now shows the full 6GB!

Cons:
There is still some slight lagginess (around 15–20%), but I believe that will get fixed soon as well.

Overall, I’m really surprised by how smoothly the installation went after spending 3 frustrating days trying everything else.


r/hackintosh • • 3h ago

HELP Stuck on "CoreAnalyticsHub start completed"

Post image
1 Upvotes

So I'm using Nullmoth 1401 3.0 to basically do everything.

Everything works fine until I load from the USB and select 1401.

Then this comes, and gets stuck here.

My hardware:
GPU: 4060Ti
CPU: Ryzen 7 8700F
Motherboard: MSI B650M Gaming WIFI (MS-7E30)
RAM: 30GB DDR5
Storage: 1TB NVMe
BIOS Mode: UEFI

I did all the BIOS things I was supposed to do according to Nullmoth.

Can anyone help?
Explained answers will be much appreciated! I'm very, very new to this, which is why I went with Nullmoth, since apparently it does everything for you.


r/hackintosh • • 14h ago

HELP Doing my first ever Hackintosh.

Post image
9 Upvotes

I can’t seem to get past this static Apple logo

Using an HP Envy x360 with an 11th Gen i5 CPU and integrated graphics, attempting this with MacOS Sequoia.

Any recommendations or help via Discord would be very helpful.

Thanks!


r/hackintosh • • 5h ago

QUESTION Can i build Hackintosh on an HP Compaq 8200 Elite SFF?

0 Upvotes

Hello everyone! I wanted to ask if it’s possible to build a Hackintosh using an HP Compaq 8200 Elite SFF, equipped with an i5-2400 CPU, a GT 710 Kepler GPU, and a hybrid UEFI BIOS.

I’m planning to use OpenCore along with OCLP; I’m currently aiming for either macOS 14 Sonoma or 15 Sequoia. I’ve read the official Dortania guide, but I’m having a bit of trouble following it, lol.

Network adapter: Intel(R) 82579LM Gigabit Network Connection (I’m using a Wi-Fi dongle for connectivity).

SSD: WDC WDS250G2B0A-00SM50, SATA.


r/hackintosh • • 6h ago

HELP I need help booting macos on amd system

0 Upvotes

I'm currently trying to boot macos tahoe on ryzen 5 7535HS but it hang on picker with "Missing GOP on ConOut - Unsupported" on opencore log


r/hackintosh • • 23h ago

SUCCESS [SUCCESS] MacOS Ventura on an Acer Aspire E5-575G with Wi-Fi working on a Qualcomm Atheros QCA9377!

Thumbnail
gallery
19 Upvotes

Hey everyone! I stayed really fascinated with the Hackintosh process after my previous post, so I decided to give my Aspire laptop a second life after it was discarded following its retirement as my old home server. This thing has both a 512GB SSD and a 1TB HDD, so I thought, why not install MacOS as its main and only OS? No dual-boot ordeal, just MacOS on the SSD and the HDD for additional storage. For context, some aspects of the laptop have been upgraded, such as its RAM capacity; but its Wi-Fi card was left untouched, and remained the stock Qualcomm one.

CPU: Dual-Core Intel Core i5-7200U
RAM: 16GB DDR4 (upgraded from when I first got it, had 8GB)
GPU: NVIDIA GeForce GTX 950M (disabled) & integrated Intel HD graphics 620
Wi-Fi card: Qualcomm Atheros QCA9377

For a long time I was told that Hackintoshing this laptop and getting Wi-Fi to work with the stock card was impossible, due to a total lack of support. However, recently, I came across a fork for this card but that didn’t work right off the bat for the Aspire (https://github.com/thekunalthakur/Ath10kMac) which i modified a bit on my side to get to work on my laptop. And it does!

Experience is smooth, which is why I picked Ventura either way. I wasn’t exactly sure of how good performance would be on later versions so I haven’t tried anything too risky. If you think I could run any newer version without major performance loss, I’m interested to hear about it; mostly for the sake of app compatibility.

What works:

  • Wi-Fi
  • Sound
  • Graphics acceleration
  • Apple Accounts, iMessage, iCloud, overall a lot of apple services (haven’t tried Find My Mac)
  • Safari, YouTube

What does not work:

  • The GTX 950M, obviously
  • My USB-C port. able to boot MacOS from an USB stick, but once inside the OS, USB-C devices are no longer enumerated.
  • The trackpad behaves weirdly, in a way that makes it unusable. Until I figure out the reason, I’m using an USB mouse.

What MIGHT work, haven’t tried:

  • Bluetooth
  • SD card reader
  • DVD player
  • ETC.

Thank you for reading! Excuse the poor quality pictures. It’s dark and my lights are dying, lol.


r/hackintosh • • 9h ago

IT BOOTS! (WIP) The rog zephyrus M16 2022 model already has tahou installed, and now we are preparing to install golden gate.

1 Upvotes

We are currently accelerating the installation process! The liberator 0.5 version is currently downloading the 27 installation software! Liberator is a cross-generational installer


r/hackintosh • • 10h ago

HELP Help!

0 Upvotes

I tried to upgrade from macOS15 to macOS27 with nullmoth's liberator on my computer. I had a lot of hard disk space to install it, but it failed.

Configuration:

CPU Intel core i5-9400F@2.9GHz

GPU NVIDIA GTX 1650 SUPER

RAM 16GB DDR4

Motherboard TUF B360M-PLUS GAMING S

SMBIOS MacPro7.1

Driver: 1401 shows 3.0,and liberator shows 2.8.1

Running log: https://docs.google.com/document/d/1Fd8Ndy_RCq7PUMncCO6uvS-dAS-QqRO8fzXUkE7VsYg/edit? Usp=sharing


r/hackintosh • • 11h ago

REQUEST Has anyone been able to hackintosh these mini pc’s?

Post image
0 Upvotes

r/hackintosh • • 11h ago

HELP Stuck in EXITBS:START when trying to boot into recovery

Post image
1 Upvotes

my specs are

threadripper 2950x

radeon rx 6750xt

asrock x399m taichi motherboard

I'm trying to get macos 26 running but I keep getting stuck here


r/hackintosh • • 1d ago

SUCCESS After so much pain, I finally installed Hackintosh. 😭👍✨🙂‍↔️

Thumbnail
gallery
22 Upvotes