r/Kseries • • 1d ago

RSX RESURRECTION, 2006 RSX PREMIUM AUTOMATIC. 🫥🫥🫥🫥

Thumbnail gallery
1 Upvotes

r/Kseries • • 1d ago

No VTEC 😠

0 Upvotes

K20Z3 with 110k km. VTEC not engaging at all, and there's a whine/whoosh from the front of the engine that's loudest right around VTEC crossover (~5800 RPM). Not a belt — already ruled that out.

Already checked:

- VTEC solenoid tested good

- Solenoid screen clear

- Oil level full

- No codes, no CEL

- Oil on the dipstick looks good

So no VTEC, no codes, good solenoid, full oil, and a whine from the timing-chain end at crossover RPM. What's the most likely culprit — oil pump, timing chain/tensioner, or the VTEC oil pressure switch? Anyone had this exact combo (no VTEC + whine, no codes)?

Getting it diagnosed at the dealer, but want to know what I'm walking into first.


r/Kseries • • 2d ago

Anyone know if this is normal for a 91212-R1B-A01 - front engine crankshaft seal?

Thumbnail
gallery
2 Upvotes

Honda.oempartsonline.com sent it in a bubble mailer which I thought was pretty dumb. Definitely don’t want to install this if it’s faulty.


r/Kseries • • 2d ago

Turbo K afr issues

2 Upvotes

So i’ve noticed that if i let my car idle for a little while the afr starts to go up and it starts to misfire. but after driving for a couple minutes the problem seems to go away. car is tuned on kpro v4. i believe the seal on my turbo may be a lil worn because i do get a small amount of oil that makes its way through the charge pipe i’m not sure if that oil coating any of the sensors would cause this issue or somethin but i figured i would test my luck here. let me know!


r/Kseries • • 4d ago

AEM Analog to KproV4

Thumbnail
gallery
1 Upvotes

I have been chasing this issue for a few weeks now to get my closed loop running properly in low load. Here's the situation and symptoms

Vehicle: 2003 Civic Si (matching ecu on kpro)
New AEM 30-0300 gauge and new FAE sensor

Wiring:
-red wire to switched 12v on add a circuit (tried mirror motor, acc radio, etc, all same symptoms)
-black wire to G101 ground
-white wire to Kpro internal AN0 pin (tried AN1 and 2, same symptoms)
-brown wire to Analog internal ground (also tried pin A10 on ecu, same symptoms)

Symptoms:
-typically reads fine after a cold start, will remain that way indefinitely until I turn off the car and restart
-reading usually gets more accurate and smooths out when I put more load on the engine (more throttle and map)
-occasionally the noise will clear up and then immediately return

For basically any given configuration of wiring it'll still exhibit all 3 of these symptoms. I even tried buying a new gauge and it still persisted. I just want closed loop 😩. Any help is greatly appreciated.

Solution:

So I went and bought a Bosch 17212 sensor from autozone for $90. Plugged it in and ran an open air calibration. Analog output is consistently smooth between starts so far. Haven't had any issues the whole day. I count that as an absolute win. I guess the FAE sensor directly from AEM was bad out of the box. Was never a gauge issue.


r/Kseries • • 5d ago

Got the longblock back from my builder and had to do a test fit

Post image
35 Upvotes

r/Kseries • • 5d ago

K20 starting issues

1 Upvotes

My Ep3 has been sat for a while, took it from the unit on about a 10 mile drive back home, worked fine,

Parked it and then went to move it, the engine cranks but doesn’t fire up even though it has just driven completely fine?

Does anybody have any pointers or advice, I’m sure it’ll be something silly


r/Kseries • • 5d ago

exhaust

3 Upvotes

do you guys think ktuned turndown 3 inlet is louder than skunk2 megapower?


r/Kseries • • 6d ago

K24Z3 190K Miles Knocking

Post image
6 Upvotes

Not the OEM Knock Sensor (replaced a year ago)

Did a bit of testing today…

Yeah so, as you can see - not good. Replace wiring harness and Knock with OEM?


r/Kseries • • 6d ago

K24a2 need help figuring out a noise it starting making

1 Upvotes

Hey guys I was wondering if I could get some help here I just bought a 2007 civic Si k24a2 swapped I just got it like 3 weeks ago and first 2 weeks it was running fine making no noises and all of sudden like a week ago it started making a noise when I’d be on the freeway going like 70 to 60 and let off the accelerator it sounds like a grind or not sure and after like the drive and when I let it idle it still sounds I don’t know if it would be my trans and my tensior problem together cause when I’m on the freeway and I push the clutch in it goes away but when it’s on idle and I push the clutch in it doesn’t go away any help would be really much appreciated thank you !


r/Kseries • • 7d ago

Question about k24a1 head bolts?

2 Upvotes

Long story short head gasket blew on my 2004 crv and im ready to install the head back on but I dont know if I should use OEM honda head bolts or go with ARP head bolts the engine isnt being used for any proformance reasons its used as a daily driver. Im just asking bc I read that the ARP bolts can potentially cause the threads to pull bc they dont stretch as much as the OEM or should I just stick to OEM ones to play it safe since the engine isnt used in a proformance application. Any feedback is appreciated thanks!!


r/Kseries • • 7d ago

L19 head stud question

Post image
5 Upvotes

So I’m finally getting ready to bolt down my head to my block. I’m using the L19 head studs from speed factory. These are the instructions provided by speed factory. For those who have used these head studs before do you follow these instructions exactly ? What are some tips or tricks you might suggest? This is a k24 engine built for boost. Using a speed factory head gasket as well. Thanks !


r/Kseries • • 7d ago

Which one of these motors would you choose and why? Looking for a replacement for my RSX

Thumbnail
gallery
8 Upvotes

Motor #1 $2400 + $350 shipping
Details : 139k miles unknown compression

Motor #2 $1900 + $500 shipping
Details : 170k miles 200PSI compression

Motor #3 $1800 + $500 shipping
Details : 202k miles 240PSI

When I get the motor I plan on doing all rubber gaskets, inspecting timing and maybe doing the valve lash. Which motor would you choose personally?


r/Kseries • • 7d ago

Broken timing guides…

Thumbnail
gallery
6 Upvotes

Picked up this K24Z3 from a local scrapyard yesterday to swap into my 09 Accord (current motor needs rebuilt). I got it home and on the stand and cranked it over. It was stiff to get moving and then I heard a popping sound. I pulled the valve cover off to discover the timing chain guides are broken in multiple places. I can't imagine this engine ever ran like this so I'm wondering if they broke in the accident that totaled the donor vehicle, but the valve cover and timing cover looks in tact and un damaged. It's clear someone has opened the timing cover before due to the excess RTV. I'm worried it jumped time. I'm wondering how much of a hassle it would be to fix, especially considering this was supposed to be a drop and go motor to drive while I take my time to rebuild the other one.


r/Kseries • • 9d ago

The Before and After; First K

Thumbnail
gallery
268 Upvotes

Been H22 swapped since 2009 and had this 1994 Accord since highschool in 2004 when my dad handed over the keys. My dad bought this Accord back in 1996 as a second owner. I lost him back in 2019. Wish he was here so he can drive and get a taste of the K series. Build list is in the comments.


r/Kseries • • 8d ago

Is this a good spot for a heat shield?

Thumbnail
gallery
10 Upvotes

r/Kseries • • 9d ago

Help

2 Upvotes

So I have a 2000 prelude I’m k swapping it putting a 9th gen civic si transmission in it it’s built I want to push around 800whp I can’t find the axels I need would anyone possibly know do I need custom axels or can I pull them off something?


r/Kseries • • 9d ago

K20z3 72k Engine sound good?

14 Upvotes

r/Kseries • • 9d ago

EP3 Transmission bearing noise.

9 Upvotes

just got my k swap prelude running and hearing some internal bearing noise any thoughts yall? It’s coming out but just wanna hear some second opinions still. But no matter what ts is coming out still
Thanks guys!


r/Kseries • • 12d ago

complete dead end

Thumbnail
gallery
13 Upvotes

quick context: upper bolt snapped for vtec solenoid while tightening . My dad decides to attempt to drill it out instead of taking the cylinder head off like a normal person or (at the bare minimum) welding a nut where the thread of the bolt is and taking it out that way. This attempt results in the sculpting of his nutsack. He tries to use JB weld to seal the hole but fucking seals the oil gallery for the vtec cam lobes. Is there an alternative to buying a new cylinder head? I took the cylinder head to a machine shop and they advised I buy a new cylinder head. Fuck.


r/Kseries • • 12d ago

Could this be the problem?

Post image
5 Upvotes

After tearing apart my new to me k24a block due to low compression in cylinder 1 this was the piston. It's the only one with marring on the piston. Do you think that little indent is the reason for the low compression and scraping on the side of the piston? And if so would putting new rings in help or just get a new piston? Thank you!


r/Kseries • • 13d ago

K20A EG6 with Jackson Racing supercharger: keeping A/C and power steering

2 Upvotes

I have a DC5 K20A-swapped EG6 and picked up a used Jackson Racing M62 supercharger. The charger didn’t come with the JR brackets, and I’d like to keep both A/C and hydraulic power steering.

The RSX manual lists alternator relocation brackets, an A/C spacer plate and lower spacers, a P/S pulley and tensioner setup, and a manifold support brace. I’m also working out the gaskets, bolts, IACV and fuel-rail spacers.

Has anyone installed this setup in an EG while keeping both accessories? Did the original RSX brackets work with your swap, or did you have clearance or belt-alignment issues? I’d also appreciate leads on the A/C spacers, P/S/tensioner hardware and manifold brace.

I found some parts at CPL Racing and a MercRacing auto-tensioner alternative, but I’m not sure what fits my setup yet. Photos or part numbers would be a huge help. Thanks!


r/Kseries • • 14d ago

K24 Tick

14 Upvotes

Hey all, new to the Honda community. I know the K series have a tendency to tick away, but just wanted to see if anything stands out here?

135,000km.

Really appreciate the insight.


r/Kseries • • 13d ago

1999 civic wanting to swap d16 5speed maunal with a k24 and a 5 or 6 speed manual

1 Upvotes

I have a 99 civic im wanting to put a k24 in i know there are a good bit of options. 1. Don't need anything super sporty or crazy just want somthing with a little more power than the d16 while still retaining that honda reliability. 2. Affordability I can do all the work myself I have the capability and know how but with all the options what would be my best bet cost wise (engine options, trans options, mount kit, axles, ect).