r/righttorepair • u/Early_Teaching6966 • 1d ago
Success: fixed blackouts every ~50 s and a dark line on an impact-damaged Samsung S95F 77" QD-OLED, from inside the TV's own panel controller (no parts swapped)
TL;DR: Impact damage left my Samsung S95F 77" QD-OLED with two faults: the picture kept cutting out (at worst every ~50 s, sound still playing) and a dark line ran down the screen. No parts were swapped. Both were fixed in software, inside the TV's own panel controller: 24 of 24 controller boots without a blackout since, and the line within 1–2 % of its neighbours from 30 % grey up. Before/after: images 1–2. Prerequisite: root access. Both TV-side fixes require a working root shell on your own TV. Use the S95F rooting toolkit and its root setup guide, then verify your TV root session. Firmware decryption is not required for either fix. Hobby project on my own TV, nothing for sale. Writing to the panel controller can brick a TV and voids the warranty.
The symptoms Blackouts that made the TV unusable. On dark or sparse scenes the picture went black while the sound kept playing, came back, then went again. At its worst every 46–51 seconds. A dark line. Six columns (1255–1260) were damaged; the worst four gave ~1 % of normal light at 20 % grey. In dark films it was a black stripe. A new 77" panel costs close to a new TV, so I looked at what the TV itself was doing first. Where the fault sits (image 3) Three parts matter: the main board (runs the TV and apps), the panel controller (TCON: drives every column, measures the panel, runs safety checks) and the panel. Both faults were the panel controller reacting to the damaged columns, not a failed board. Fault 1: the blackouts (image 4)
- Diagnosis: while the picture is on, the controller checks each lane (about two columns) against a reference. The damaged lanes failed, a fault score climbed past its limit (40) and the controller switched the picture off. The TV reset the controller, the check failed again, and the loop repeated.
- Fix: the controller has its own per-lane "skip" flag. I set it for the damaged lanes (540–661) in the controller's working memory, so that one check leaves them out.
- That memory clears whenever the controller restarts, so a small always-on computer puts the flags back after every controller boot and reads them back to confirm.
- Result: 24 of 24 controller boots clean.
- Trade-off: that one check is off for the damaged lanes. It stops the false trips; it doesn't repair the damage. Fault 2: the dark line (image 5)
- In standby, OLED TVs run a sensing scan (the same one as "Screen Optimization" in the menu) and boost columns that have got weaker.
- My damaged columns gave a false strong reading, so the TV gave them no boost at all.
- Fix: just before the TV's own standby scan, I lower the sensing gain for those columns in controller memory. The scan now sees them as weak, boosts them, and the TV saves the result itself. If anything goes wrong, the next normal scan puts the stock values back.
- It took 11 calibration runs (one TV scan each), in small steps. One run overshot and made two columns glow near black.
- Two small runtime trims on top (a per-lane gain and the blue weight), re-applied after each power-on. Results | | Before | After | |---|---|---| | Blackouts | picture off + controller reset ~every 50 s at worst | 24 of 24 controller boots clean | Line brightness ÷ healthy neighbours (camera; 1.00 = identical; before = worst 4 columns, after = band average): | Grey | Before (worst 4 columns) | After the fix | |---|---|---| | 100 % | 0.43–0.67 | 0.99 | | 50 % | 0.11–0.30 | 0.99 | | 30 % | 0.01–0.07 | 1.00 | | 20 % | ~0.01 | 1.03 | | 10 % | black | 1.06 | | 5 % | black | 1.14 | What you need, and what's not perfect
- Root on your own TV (see above), a small always-on computer, a camera on a tripod and a media player for test patterns.
- Very dark greys on the band are slightly yellow (blue is short below ~30 % grey). There's no per-column way to fix blue alone on the TV side.
- Firmware auto-update stays off: an update would remove the fix.
- It only works if the damaged columns still light up and the TV's compensation reads them wrong. Electrically dead columns can't be boosted. Links
- Repo (write-up, scripts, guide): https://github.com/TheMHD1/samsung-s95f-display-lab
- Step-by-step guide: https://github.com/TheMHD1/samsung-s95f-display-lab/blob/main/tools/tcon-calibration/GUIDE.md
- Blackouts, deep dive: https://github.com/TheMHD1/samsung-s95f-display-lab/blob/main/docs/advanced/BLACKOUT-MITIGATION.md
- Line, full write-up: https://github.com/TheMHD1/samsung-s95f-display-lab/blob/main/docs/advanced/tv-calibration/WRITEUP.md Happy to answer questions.
