r/Luthier • u/RosewoodBraz • 2h ago
ACOUSTIC Bridge day!
Putting my ebony bridge onto my torrified spruce topped OM.
r/Luthier • u/scottyMcM • 3d ago
Hi everyone, I want to check in with you all and see if the membership feels like we should change the rules around advertising here.
To explain, the rules were in place long before I took over. As they are now, advertising is strictly limited to members who have good standing with the community and have a history of helping out by answering questions etc. Even then, posts are strictly limited.
Most of the time I don't need to intervene much at all in the sub, but the majority of reports I do get are for unauthorised advertising. I also receive mod mails from people and companies looking to advertise.
I won't make any changes without a clear mandate from the membership. I'm open to making whatever changes if any people advocate for.
Some suggestions might be one day a week or month where advertising is allowed, advertising is only allowed if offers are being made to the membership?
I'm sure there will be the people who regularly want or try to advertising who will be voting to open the gates so if you feel strongly against it please do let me know.
If you have any other comments or suggestions please do let me know below.
r/Luthier • u/RosewoodBraz • 2h ago
Putting my ebony bridge onto my torrified spruce topped OM.
r/Luthier • u/Jojochuchu • 24m ago
Sorta f'd up the neck pocket aesthetic-wise, it still bolts on fine and all that but it looks a little wacky. I've tried my best with the carving but I noticed quite how difficult it actually is (my respect for you professional luthiers has gone up so much when building this) I'm not done with the carving, I've still got a couple of standing sessions left so it's still a bit uneven, but I'm not sure about how I'm actually supposed to finish it up cause I'm worried about accidentally sanding too deep and leaving indents
I'm thinking about a walnut stain and then a few clear coats, but I'm not sure. Is there anything I ought to think about or maybe pay attention to when finishing this body up?
I do want to say that I won't add any sound holes since that's beyond my guitar knowledge, and I've heard that they're quite tricky to get right, my only ambition with this guitar is to learn and in the end have a playable, cool looking guitar, and hopefully that's where I'll end up
r/Luthier • u/IronMike5311 • 42m ago
I know this old fiddle is beat to heck & isn't worth much. But it has a family history of square dances up in the mountains, and the only object saved by my great grandmother in a house fire around 1990. It must've meant a lot to them. Played with by kids early 1900's & kicked around in the attic since.
Would you leave it as is & hang it decal-side out? Or could I add new tail piece, bridge, strings & pegs to at least resemble what it once was? It's only going on the wall, I'm sure. I didn't check for a label, but I'm sure it was mail order & common
r/Luthier • u/hontslager • 53m ago
How many guitars does one have to build to be a Luthier? Or is it counted in years or customers?
This one ended up better than I hoped for, given the number of mistakes I made - that's what you get from improvising and not working with a plan or drawing I guess. Here's some of the things that went wrong, sharing my errors so others don't have to make them:
- I glued and clamped the neck on the body and let it sit to dry overnight, but in the morning I found the the assembly had fallen over! The tilt of the neck is now somewhat too steep, but that was solved with a 3mm shim under the bridge, easy fix. Worse, the angle of the neck is also slighty off, I had to move the bridge about 5mm for my strings to sit straight on the fret board. That's no problem for the guitar itself, but the pickup holes now are slightly off! Luckily the tolerance of the EMGs is wide enough, no adverse effects on the sounds. Lucky escape here. I might one day find the courage to take the neck off and set it straight, but for now I'll leave it as is - it kind of fits the deliberate wonky design of the rest of the guitar
- When gluing the fret board on the neck, the moisture of the glue warped the fret board side ways - I had put on about 20 clamps, but that was not enough, so I ended up with a 0.5mm gap between fret board and neck in some places. This was just too ugly, so I undid the glue with heat and violence, which was not too bad - about an hour to get the fret board up, and 30 minutes to clean up the grimy mess afterwards. The second glue up I did with an elastic rope wound tightly around the neck, and it came out nice.
- The headstock, silly me: this is one of these 'oh almost done, let me quickly..' kind of mistakes - i drilled the holes for the machines at equal distance from the sides, not taking into account the direction of the strings. It tunes and plays fine but it looks kind of funny. bah.
- I buried the truss rod nut slot: last minute I decided to stick some leftovers of the front wood on the head stock but forgot to saw out the slot for the truss rod access. Well, so be it: as long as I don't have to tweak the rod it just sits nice there, and now I don't have to make a cover for the hole. If I ever need to tweak the neck I will have to dig it up though.
Even with all the imperfections, I do love how it ended up: the instrument is a delight to play, has a lovely deep growl sound, it's nice and light to hold for long time. And lastly, the deliberate wonky placement of the pick ups is a nice conversation piece!
Thanks to all posters in r/Luthier for the years of inspiration and knowledge!
r/Luthier • u/Devilst0rm • 3h ago
Hi everyone
So just wondering if this is easily sorted myself. I have some fret buzz on the 5th fret E string. It is literally just isolated to this spot. If I bend the B string to the same position on the E it does the same thing. The guitar doesn’t buzz anywhere else. I literally think just the end part of the fret need a little bit removed with a spot level. Is this easy to do? I was looking at getting Frtlzt spot level to do it? Should I consider anything else?
Thanks
r/Luthier • u/Ok-Bluebird-6309 • 11m ago
I found several cracks here and there on the ebony fretboard of my E-II Viper while putting Dunlop 65 lemon oil. After wiping off the oil, it’s barely visible-as shown in the second photo-but is any further action required?
r/Luthier • u/agasizzi • 22h ago
i Could have sworn I filled the grain well and sanded smooth, ahh well, I sanded down the nitro after the last failed metallic coat and hit it with black again, this run is better, still not what I’d hoped for, but I’m going to go ahead and move forward with the build as a first run just for me. May avoid chameleon paint for a while though.
r/Luthier • u/kshitij2713 • 5h ago
I have a stratocaster and I recently adjusted my saddle height, then suddenly all of my strings started to make a weird noise which was coming from the bridge. I checked the neck relief, checked for any loose part in the bridge checked my tremolo springs and also tried raising the saddles a bit but I can't fix the problem. I also muted the string from the nut as it was more clear by doing that
r/Luthier • u/Salt-Ganache-5710 • 23h ago
I have a left handed sire j5. I've replaced the bridge with a jaguar style bridge.
The tremolo doesn't seem to do anything. It was loose, but is now screwed in. As well as this, it's making loud rattle when played.
It shipped like this from Andertons.
Can anyone assist before I have to send it back?
r/Luthier • u/CWAmericana • 18h ago
Finally got some good winds in thanks to this sub. Sounds fantastic and really helped demystify pickups for me.
r/Luthier • u/Thickwhitedukee • 12h ago
My band mate offered to sell me this riviera for $200 bucks and I’ve been wanting a casino so I’m considering it. Could this be fixed with wood glue and clamps ? I don’t want to buy a guitar for 200 just to put a ton of money into it
r/Luthier • u/doperidor • 1d ago
Also made an instagram @hedonicdesign if anyone is interested!
r/Luthier • u/Moneyleaves • 1d ago
Lost it somewhere, didnt notice it. How do I find it in the guitar webshop?
r/Luthier • u/arseholierthanthou • 21h ago
I have a wenge fretboard blank but it's 1 or 2 mm too thin, so I can't guarantee it will be absolutely thick enough to hold the full height of every fret tang once it's radiused.
How ok would it be to make up the height with a veneer or two underneath it? So the layers would go neck wood, then truss rod cavity, then a couple of veneer sheets and then the fretboard.
Would veneers be strong enough for that? Or would hammering in frets crush them or similar?
r/Luthier • u/EbbCommon4660 • 17h ago
Hi, I have a need for a fret that will fit an .018 (eighteen thousandth of an inch) fret slot. Can you help? thanks .......noobie, but this is for my guitar crazy bro. Bro is not especially particular about anything else, just that measurement. thank you again!
r/Luthier • u/I_AM_4HEAD • 18h ago
Working on a build which I want to be the full package with all the ergonomics and bells and whistles one may wish for.
So I wanted to ask, what features like a strandberg neck, sustainiac pickup, fanned frets, ouput jack positioned at the top back etc have you guys seen that were a thing you liked.
Like, given you had free reign, what features would your perfect build have for ergonomics, sound, flexibility etc?
r/Luthier • u/Subject-Finding1658 • 1d ago
I've had this Schecter for about 2 years now and when I first got it, it played perfectly with the hipshot saddles almost flat. A while back it developed a minor buzzing problem with the high e string at the 15th fret so I had it set up to fix it. When they fixed it the guitar tech raised the saddles as well.
Neck relief, string height and string radius all seem okay but there is still buzzing around the 7-8th frets. Even if I increase neck relief the buzzing doesn't go away, especially on the D and G strings. Checked with a fret rocker and all frets seem level.
It is set up in drop C tuning with 10-52 gauge strings.
Now whatever I do I can't seem to get it to play the same as it did before. Lowering the saddles back to how they originally were seems impossible. Is there anything I can do to solve this or am I just going mad? Could the buzzing be caused by anything else e.g. string height in the nut?
Also, unrelated issue but is it normal for my Hipshot bridge to have so much wear after a couple of years? I palm mute a lot but the metal is wearing away.
r/Luthier • u/Infinite-Tone-4967 • 1d ago
I've had pretty horrible experiences hiring luthiers and techs. Although admittedly the work I need done on my normal guitars is typically not something a tech or luthier would ever encounter: installing sustainiacs with custom wiring, installing and routing for a Floyd Rose, routing for a battery box, refretting a guitar, refinishing a guitar neck while trying to stain and perfectly match the color of the headstock...
That being said, I live in a major city in Texas. I have hired around six different experts who all assured me that they could handle the job, even when I explicitly warned them of the difficulty, and all of them failed. Oftentimes I got my guitar in worse condition than I gave it to them in. And they still wanted me to pay them for their crap.
So, I don't trust them. I've learned to work on my own guitars. My newest guitar has a normal guitar nut, but it came from the factory in a horrible condition. I want to install a graphtech nut, and I want to cut it from a blank. I think I'm pretty methodical and I take my time learning what I need to do and going at a slow pace to make sure I don't mess up.
What all am I going to need, are there any online resources on how to do this without me going to a luthier school and having someone teach me? Am I going to mess up my first nut, should I just buy an extra blank assuming the first one's going to be bad? What are the tools I need?
r/Luthier • u/WholestepHalfstep • 19h ago
Ok, for finishing this LP jr kit-
My plan is…
First step is prepping the parts getting the neck and body scuffed/sanded to 1000 grit
2nd step is filling the grain with DAP Premium grain filler (fwir I should thin this stuff first, apply across the grain with a trowel or putty knife) giving ample time to dry
3rd Is more sanding to smooth the parts back out
4th is rubbing tru-oi on with the grain and letting it dry/set/cure or whatever that’s called
5th is to buff the parts with steel wool 00
6th will be reapplying the oil until I’m happy with the outcome
7 will be to glue and clamp the neck/body and letting it sit for a day (or 2) to be certain the neck and body are good and solid
8 apply tru-oil across the now solid body/neck as even as possible
9 sand/buff everything to 00 steel wool satisfaction again
10 let sit for at least 24 hr before installing anything
Questions;
Are the steps in the correct order?
Am i overlooking anything?
If I wanted to darken/redden the wood, is It better to do this while grain filling? Or while rubbing on the oil? Can I just add the coloring to the grain filler or the tru-oil before using it?
Tips on the best way to treat the neck and fretboard are welcomed
The wood is mahogany
r/Luthier • u/Fit-Strain3834 • 20h ago
Hey guys,
I’ve been considering picking up a PRS SE Silver Sky lately and have been digging through this Forum and YouTube to check out real world impressions before buying.
I stumbled across this video where the guitar needed quite a bit of work right out of the box like super high action, notes choking out on bends around the 18th fret, and a nut that wasn't even glued in properly and so on:
I always had the impression that PRS SE guitars were super consistent straight from the factory?
For those of you who own one or have played a few – how was yours out of the box? Did it play great right away, or did it need a to se a luthier for some work?
Thx
Talib
r/Luthier • u/PassageCareless • 1d ago
I'm not a luthier and might destroy a perfectly good guitar, but I'm about to embark on a journey to build my wife a guitar from her favorite movie, Kpop Demon Hunters. I bought a used, fairly cheap, Mexico built Acoustasonic Telecaster. So here's my tentative build process:
1)Autocad the floral design (started today)
2) Laser engrave (local maker already approved the work just needs file)
3) Sand and paint (still researching paint but need matte black and pearlescent)
4) epoxy resin/glue pearlescent powder or crushed mother of pearl the inlay
5) need to research polishing and top coats
Feel free to leave tips, tricks, or advice. Hell, feel free to tell me how stupid I am 😅
r/Luthier • u/Typingdude3 • 22h ago
I have a new Gibson SG and one of the knobs has a slight click when you turn it. It’s hard to describe besides that. There’s really no resistance, it’s not hard to turn, but it’s like a contact is being hit in the cap or something is loose in the cap. Any ideas?