r/AMDHelp • • Jun 30 '25 All Seeing Upvote This Helpful WOW Bravo Heartwarming Popcorn Mindblown

Tips & Info Ultimate AMD Performance Fix Guide: Stop Lag, FPS Drops & Boost Speed (2025)

3.4k Upvotes

🌞Created in 2025 and kept fully updated for 2026

If you’re facing low FPS, lag, stuttering, or crashes on a new or old AMD setup (AMD CPU with Radeon/NVIDIA GPU, or Intel CPU with Radeon GPU), you are in the right place. This guide has tested and proven solutions and user tips to maximize your system's performance. You will be see hardware checks, BIOS configurations, Windows tweaks, and driver changes here. Real-world solutions that work, not guesswork.

Disclaimer- The following optimizations are based on community-tested methods that have safely improved AMD system performance for most users. Since every setup is unique, results may vary. Proceed carefully and apply these tweaks at your own discretion. (This guide follows the Acer Community format.)

Read all Important Notes and Notes in each step. They contain vital information to guide you on how to avoid issues and when to revert to earlier changes.

=> Hardware Installation & Setup

Before you adjust BIOS or Windows settings, ensure your hardware is properly set up. Most issues such as low FPS, stuttering, and crashes are caused by minor errors such as installing the GPU in the improper slot or RAM, etc. This section contains crucial checks which have resolved serious issues for many users. Even if your PC boots and is usable, these kinds of issues might be latent, and resolving them can have a massive difference to performance.

1. GPU Installation — TOP PCIe x16 Slot (Closest to the CPU)

Always install your graphics card in the top PCIe x16 slot, Which is the slot nearest to the CPU.

Why it's important:
•It is configured for full x16 bandwidth and is plugged directly into the CPU.
•Lower slots have x8 or x4 speeds, limiting GPU performance and bringing in bottlenecks based on the board.

Common mistake:
Most users inadvertently install the GPU in a lower PCIe slot or fail to confirm if the top PCIe x16 slot is delivering the GPU’s full bandwidth supported as per their GPU (such as x16 or x8), resulting in low FPS or instability.

Confirm true Speed:
Download and Open GPU-Z, then check the “Bus Interface” field. The left side (before “@”) shows your GPU’s maximum lanes and PCIe generation (e.g., x8 5.0), while the right side (after “@”) shows the current active lanes and gen speed (e.g., x8 1.1).

If it shows “1.1”, that means the GPU is idle, run the GPU-Z Render Test (“?”) to display your true gen under load. Both sides (lanes and gen) should match your GPU and platform. If the current gen is lower than the max, it’s usually due to motherboard, CPU, riser, or extension cable limitations, this is normal unless you upgrade hardware.
The same can apply to lane count, but that’s more important than gen speed. The lane width/speed (like x8, x16) should match on both sides or reach the maximum your system supports, as a lower lane width can noticeably affect performance.

If lanes are lower than expected, reseat the GPU, check if the PCIe lanes are shared with other slots (see your motherboard manual), and ensure no riser/extender or older CPU is limiting bandwidth.

2. Critical Power & GPU configuration Checks

• Insert the monitor cable directly into the GPU HDMI or DisplayPort (DP) port. Avoid inserting the monitor into the motherboard port.

• Utilize all CPU power connectors or CPU power headers that your motherboard has
• Always use specialized PSU cables. Never use splitters or adapters for EPS power. Connect cables directly from your PSU to your motherboard. Don't be cheap; don't go cheap.

•Always Use quality, dedicated PCIe cables from your PSU to each power connector on the GPU. Avoid daisy-chaining (using a single cable for multiple connectors) as it can cause instability or crashes, especially on high-power GPUs. Also, make sure your PSU meets the recommended wattage for your GPU.
• Always use good-quality PSU cables, never buy  cheap extensions or riser cables.

• If your PC slows down, freezes, shows low CPU clocks despite a proper setup or lag and stutters while gaming , try plugging it directly into a wall socket or a high-quality strip. Faulty/old power strips can cause poor power delivery and hidden throttling issues.

You guys must check this as nothing can work if hardware configuration is not proper.

3. RAM Configuration – Correct Slot + Enable XMP/EXPO + check Settings.

To get the best performance from your RAM, ensure it is installed in the right slot and properly configured. Many systems perform poorly due to incorrect slot placement or missing BIOS settings.

• Install RAM in the correct slots
If you have 2 sticks, plug them into slot 2 and 4 (usually marked A2 and B2) as these slots are typically the second and fourth slots away from the CPU. This allows dual-channel mode for optimal performance.

If you insert them into the wrong slots, the system will run in single-channel mode, lowering memory bandwidth and reducing FPS in games. Always refer to your motherboard manual for the slots layout and double-check it if you're unsure.

• Enable XMP or EXPO in BIOS
Enter the BIOS and enable XMP (or EXPO for AMD kits). This will set your RAM's rated speed and timings. Just ensure the profile you choose does not exceed your motherboard's highest supported memory frequency, as a higher profile can lead to instability.

Some motherboards have a few profiles; pick the one that matches your RAM's highest rated speed (like 3200, 3600, or 6000 MHz), as long as it's within your motherboard's support range.

If you don't enable XMP or EXPO, your RAM will run at default JEDEC speeds like 2133 or 2400 MHz, which seriously bottleneck your system.

• Confirm settings in Windows Open Task manager → Performance → Memory. Check that the Speed value matches your RAM's XMP/EXPO profile speed that you set in the BIOS and is not a different number.

Download CPU-Z, go to the Memory tab, and make sure Channel displays Dual or 2×64-bit for DDR4 and 4x32-bit for DDR5. If your speed or channel is wrong, check your BIOS settings and RAM slots again.

• Check RAM Stability (Must be done after building/installing new RAM )
Test your RAM with MemTest86. If you got any errors with the highest XMP/DOCP profile selected, then test the next lower profile, such as from XMP Profile at 6000MHz to XMP Profile at 5800MHz, and continue lowering until you find a stable profile. It’s crucial that your RAM is fully stable to ensure reliable system performance.

=> BIOS Optimization & Performance Fix Tweaks

Once your hardware and power is set up, change the key BIOS settings that impact AMD CPU, RAM, and GPU performance. These can fix instability, crashes, and poor performance. Only modify the settings mentioned here. BIOS menus can differ by brand, so names or locations may vary; if you don’t see a setting, look around.

4. BIOS Update

If you are facing RAM instability, poor CPU/GPU performance, updating your BIOS may help, especially on AMD systems where the BIOS updates usually improve stability and compatibility.

To Update BIOS:
Visit your motherboard manufacturer’s website, download your most recent stable BIOS for your specific model, and carefully follow their official instructions to update safely.

Note- BIOS update may reset all BIOS settings. If this occurs, don't forget to re-apply all changes from the BIOS Optimization & Tweaks section.

5. Set Global C-State Control to Enabled (Not Auto)

Changing Global C-State Control from "Auto" to "Enabled" will help fix FPS drops, downclocking, or instability. Most people with Ryzen CPUs (such as X3D chips) see less stuttering and smoother gaming performance when C-States are enabled. Many have found that "Auto" behaves like "Disabled." Therefore, I strongly recommend switching it from Auto to Enabled.

To change the Global C-State Control setting:
→ Press BIOS/UEFI key during boot to access the BIOS.
→ Click on the Advanced or AMD CBS tab and find Global C-State Control (perhaps be under CPU Configuration or Advanced).
→ Change the value from Auto to Enabled, this fix works for most users.
→ Save and exit BIOS, then check performance.

Important Note- Rarely, some boards (e.g., certain ASUS models) may get mouse lag, freezes, or black screens. If that happens, revert to the original setting. If it causes a black screen or boot issue, reset CMOS to recover.

6. Set PCIe Gen Mode 5 or 4 or 3 Manually (Do Not Use Auto).

On some motherboards, leaving PCIe generation in Auto mode can lead to compatibility or performance issues like black screens, no signal, or reduced GPU bandwidth.
Manually selecting a stable PCIe version —Gen 3, Gen 4, or Gen 5 can fix these problems.

To configure PCIe Gen mode:
→ Boot into BIOS at startup.
→ Go to the Advanced, Chipset, or NBIO Common Options section.
→ Locate PCIe x16 Link Speed (or similar), then Switch the setting from Auto to a specific version:
• If you have a Gen 5-Capable GPU and motherboard: set to Gen 5.
--If you encounter instability, crashes, black screens, or signal loss, lower the setting to Gen 4.
• If you have a Gen 4-capable GPU and motherboard, set to Gen 4
-- If experience instability, reduce the setting further to Gen 3.
• If you have a gen 3 GPU then set Gen 3.
→ Save changes and exit BIOS.

7. Enable Above 4G Decoding & Resizable BAR (NVIDIA & AMD — FPS & 1% Low Boost, Test Required)

These features allow the GPU to access larger memory blocks directly, which can improve the performance of most games in use today. It is turned off by default even on some compatible boards due to component compatibility problems and must be tested. Most of users will get great results.

To Enable these settings:
→ Boot into BIOS at startup
→ Go to Advanced Mode
→ Disable CSM (From Boot Section, Set Launch CSM to Disabled).
→ Now, Go to PCI Subsystem tab/menu and set Above 4G Decoding to Enabled. (Location may vary, so find and confirm).
→ Then set Resizable BAR to Enabled (option appears after Enabling 4G Decoding).
→ Save & exit BIOS, then test performance.

Important Note - Disabled by default even on supported boards because of component compatibility issues, so users will have to test it. On a system where these settings are unstable, it can lead to crashes, performance issues or boot problems particularly with old components.

So, Test thoroughly and immediately disable it if you notice any instability or performance issues after enabling.

=> Windows Optimization & Performance Tweaks

This section outlines important Windows settings and tweaks to address stuttering, latency spikes, FPS fluctuations, or overall system lag. These tips work for both NVIDIA and AMD systems.

8. Clean Install AMD GPU Drivers — Fix Performance, Crashes, and Common Errors (e.g., Driver Version Mismatch)

Some of you may be facing game crashes, stutters, or random freezes. These issues often arise from a faulty AMD driver or because Windows Update quietly replaced your GPU driver, causing instability. You might also see errors like:
• “Radeon Software and Driver versions do not match...” or similar errors.
• Missing AMD software features like FSR 4, etc.

If you're facing these issues, this step shows how to clean install a stable AMD driver and stop Windows from replacing it again.

Important prerequisite - Before starting, disable Fast Startup to avoid boot conflicts that can cause sudden FPS drops, driver timeout or future issues.

Follow these steps one by one:
• First, we will download 4 files and save them in a new desktop folder. They will include the AMD software installer, DDU, AMD chipset driver, and Microsoft Update Hide Tool.

• Don't install, just download and save both the AMD software installer (.exe) as well as the AMD chipset driver installer software from the official AMD driver site that you want to install. Make sure you're downloading the specific version, not the auto-detect Tool.

Note - Newer AMD drivers can have system-specific stability issues like crashes. Try the latest version first. If problems arise, revert to 26.9.2. If you still encounter problems, try 26.3.1 as a fallback. If facing driver timeouts or crashes, also follow Step 13 of this guide after completing this step

• Download DDU and Microsoft Update Hide Tool from these links:
Microsoft Update Hide Tool (wushowhide.diagcab) - https://download.microsoft.com/download/f/2/2/f22d5fdb-59cd-4275-8c95-1be17bf70b21/wushowhide.diagcab
DDU - https://www.guru3d.com/files-details/display-driver-uninstaller-download.html

• Now pause Windows Update and disconnect Wi-Fi or Ethernet, whichever you use, and don't connect or resume updates until I say.

• Boot into Safe Mode, then extract DDU and open it. Select Device type GPU, then select AMD and click on Clean and Restart. Wait for completion until DDU uninstalls the driver properly.

• After restart, right-click on the Windows icon, then click on Installed Apps. From here, find and uninstall any chipset driver software. If it's not available, then you never installed the chipset driver manually and those users skip this point. After uninstalling the chipset driver software, click on Restart.

• After restart, open the folder where you placed the AMD driver software installer (.exe) and install it.

• After installation, restart your PC or laptop.

• Now connect to Wi-Fi, then immediately open the Microsoft update hide tool (wushowhide.diagcab). Click on "Hide Update," then select every update whose name starts with "AMD" or "Advanced Micro Devices," etc. Make sure to select all updates labeled as "AMD" or "Advanced Micro."

(If you don't see these updates in the windows hide tool then you can skip this part as windows is not overwriting the driver in your system so there's nothing to hide.)

• After selecting all, click Next. All updates you selected will be shown as fixed on the next screen. If it shows, then you have successfully done this.

• Now restart and Windows will not overwrite AMD drivers anymore. You can now resume the Windows Update.

• Now install the AMD chipset driver software. After installation, it will give two options. You need to click on View Summary and make sure all chipset drivers are installed properly. It will say Success or Installed. If properly installed.

For those users, whose summary shows any Failed chipset driver, uninstall the chipset driver again from Windows Settings and run chipset driver software again. If it still shows the same, then uninstall it again and download and install a different chipset driver version.

Note: Big Windows updates may reset this setting. If that happens, follow these steps again, but that's rare.

9. Community-Favorite: Windows 10/11 Optimization Guide (Works on all PCs and laptops. Includes NVIDIA stable drivers and must-have performance fixes!)

Implement the system-wide changes from the following link. These are general Windows steps that work on any PC or laptop, regardless of brand. The guide is simply hosted on Acer’s community forum, but it is not Acer-specific. It have been successfully applied by millions of users across many hardware setups. This is one of the most tested and effective Windows optimization guides available.

Following this optimization guide (hosted on the Acer community) fully can boost 1% lows, improve FPS stability, and fix stutters or lag while gaming by optimizing windows.

→ NVIDIA users: The Windows optimizations in the community guide linked below can further improve performance and stability. For the best performance benefits, follow all of the steps. For NVIDIA crashing issues while gaming can often be fixed by following Steps 1 and 9 of the guide.

→ AMD users: Skip Step 1 in the community guide and start directly from Step 2 (Chris Titus Tech utility step) through the end for stable FPS and improved performance. Don’t follow Step 1, as it’s already covered in this Reddit guide.

Here is the community guide:
https://community.acer.com/en/discussion/612495/windows-10-optimization-guide-for-gaming/p1
→ This guide Covers important issues like system lag, background processes, turning off unnecessary Windows functions, etc in one place.

10. Set an Optimal Mouse Polling Rate (500Hz or 1000Hz Depending on Your Needs; Fixes movement Stutters in games and high CPU Usage)

Most modern gaming mice have dedicated software (e.g., Logitech G Hub, Razer Synapse, SteelSeries GG) that allows to adjust the polling rate, how often the mouse reports its position to the system. If you don’t have the software, download it from your mouse manufacturer's website based on your specific model.

To change the polling rate, Open your mouse software and set:
• 500Hz for solid, sufficient performance with lower system load. Use it for Single-player (AAA), slower-paced, or visually rich games.
• 1000Hz for esports as it provides faster response.

There's really no benefit going higher than 1000hz, so don't waste your system performance.

Note- If you still want to use polling rates above 1000Hz (like 2000Hz or 4000Hz), test for any lag or stuttering, as higher polling rates will consume the CPU more.

11-A (AMD Users) — AMD Software: Explained Tweaks & Must-Disable Settings for Smooth Performance

AMD's default driver settings aren't always the best for smooth gaming. These info have helped many improve FPS consistency, reduce input delay, and eliminate stutters.

Part - 1 Recommended Adrenalin Settings:
Make these adjustments in the Graphics section under the Gaming tab of the AMD Adrenalin Software. This way, the settings apply to every game, including new additions and those launched from the desktop.

• Radeon Anti-Lag → Disabled (This feature often causes micro-stutters. It's wise to turn it off and use it in those games which can really get benefits from this feature. It works great in GPU-Limited scenarios. Test per game and use if its stable)

• AMD Fluid Motion Frames (AFMF) → Test First (It's a frame gen and they often adds input lag. Test it per game, if the game runs well and input lag isn’t an issue (or it feels fine), then you can use it.)

• FSR 4 (Driver-Level) → Use if Available

• Radeon Chill → Disabled/Enable (Enable this only if you want to cap your FPS, and set both the min and max values to the same number for best results.)

• Radeon Boost → Disabled (May lead visual artifacts and stutter. It works by blurring motion. Test and use this feature if you wish)

• Enhanced Sync → Disable/Enable (It can cause stutters or unstable frame pacing in some games, so it’s generally safer to keep it off and use FreeSync if available. If you want to use it, test for stability first. It works best when your FPS is well above your monitor’s refresh rate, for example, 120 FPS on a 60Hz display offers smoother gameplay than V-Sync, with less tearing and lower input lag).

• Reset Shader Cache → Expand Advanced Settings, then find and click the Reset Shader Cache option to clear stored shaders and fix performance issues. Highly recommended after driver or game updates. Expect longer loads or brief stutters at first as shaders rebuild, performance stabilizes once cache regenerates.

Note - If you had games added before this, reapply the same settings manually in each game under the Gaming tab.

• Turn off ReLive features (Especially Instant Replay): → Go Record & Stream tab, then find and disable ReLive recording features like Instant Replay, Record Desktop, Streaming, etc. Instant Replay is particularly responsible for stutters, FPS drops, and driver timeouts. Turning this off alone can resolve your issue.

• Disable Unnecessary Features→Click the Settings gear icon, Go to Preferences, then disable web browser, Advertisements, Game Adjustment Tracking and Notifications, Tutorials, Animation & Effects. while keeping System Tray Menu and Toast Notifications enabled for better responsiveness.

Another setting in the Preferences tab is the AMD Overlay, which many people use, so I didn’t include it with the other disabled options above. However, some users have reported that the AMD Overlay can cause major performance issues for them, so if you’re facing stutters or FPS drops, try disabling it and test again.

11-NV (Nvidia Users) — NVIDIA App Settings for Smooth Performance

Important prerequisite - Before starting, disable Fast Startup from Windows settings and clear shader cache. This is highly recommended after driver or game updates or when facing performance issues. Use this NVIDIA link to clear the shader cache properly:
https://nvidia.custhelp.com/app/answers/detail/a_id/5735/~/deleting-nvidia-shader-cache-files

And Expect longer loads or brief stutters at first as shaders rebuild; performance stabilizes once cache regenerates.

NVIDIA App Settings

Follow these NVIDIA App settings for the best optimized gaming experience. This will Optimize GPU performance, reduce input lag, and eliminate common stuttering across all games.

Where to Apply Settings:

Laptop - In NVIDIA App (Settings > Graphics tab > Per-App Settings), add each game.exe, set Preferred Graphics Processor to High-performance NVIDIA Processor, then apply settings per-game for max performance.

Desktop - In NVIDIA App (Settings > Graphics tab > Global Settings), apply settings globally to affect all games.

Essential settings:
• Power Management Mode → Prefer Maximum Performance (Prevents frequency drops that cause stutters.)
• Shader Cache Size→ Unlimited (Helps reduce shader compilation stutters.) Here in Shader Cache settings, Set Automatic Shader Compilation → On, keep System Utilization → Medium (Default), then click Apply.
• Set PhysX Configuration to NVIDIA GPU. To set Go to Settings → Configure Surround, PhysX. check path in nvidia app yourself. (Avoid CPU or Auto-select, it causes stutter and high CPU usage.)

Laptop Users:
• In NVIDIA App, Go to Graphics > Global Settings > scroll down, click Show Legacy Settings > → turn off Whisper Mode.

Now for the features tab:
In NVIDIA App > Settings > Features tab.
• Turn off "Game Filters and Photo Mode". You can sue this feature if you want but know that this also causes performance drop.
• For max performance, Also turn off NVIDIA Overlay from there. It's features like Instant Replay can cause stutters and FPS drops.
• Turn OFF "Automatically optimize newly added games and mods".

Now, click on the Privacy tab and Turn OFF:
• "Configuration, performance, and usage data".
• "Error and crash data".
• Keep "Required data" as it may be needed for basic functionality.

12. Inspect your Realtek PCIe 2.5GbE Family Controller – Fix lag, audio glitches & Stutters (also affects Wi-Fi if the controller is present in the system, even if you never use Ethernet)

Some systems with the Realtek PCIe 2.5GbE Family Controller can have issues, even if you use Wi-Fi only, don’t skip this step. The controller can cause random stutters, FPS drops, audio glitches, or ping spikes even when not in active use. For a Quick test, Disable it in Device Manager under Network adaptors, and play your offline game or online via wifi; if fixed, it's the culprit.

You have two straightforward choices:
• Keep it disabled in Device Manager and play your offline games and online using Wi-Fi smoothly (Ethernet won't work in this option).
• Fix the Realtek PCIe 2.5GbE Family Controller. driver with these steps (detailed below) to use Ethernet smoothly.

Solution:

Download and save this 10.54.1111.2021 stable driver version of this controller- https://catalog.s.download.windowsupdate.com/c/msdownload/update/driver/drvs/2022/05/2e830a2a-a689-4e43-96be-06bd8dc7e75b_e5bc281dbf962e2551cc18cdee4abd0b55949b61.cab

Installation:
• Pause windows updates and open Device Manager → Network adapters → right-click Realtek PCIe 2.5GbE Family Controller → Uninstall device → check “Delete the driver software” (if available) → Restart.

• Extract the .cab file to a folder of your choice

• Go to Device manager → Network adapters → right-click Realtek PCIe 2.5GbE Family Controller → update driver. → "Browse my computer for drivers" → "Let me pick from a list..." → "Have Disk".

• Browse to the folder where you extracted the driver, open it and select the inf file and click Ok, Wait for installation.

After installation,
• Disable automatic driver updates so Windows Update doesn’t overwrite this version:
Go to Settings → System → About → Advanced system settings → Hardware → Device Installation Settings → select No, save → Resume windows update and Restart your pc.

• This setting stops most automatic driver installs, but a big Windows update can still change the driver later; if that happens, which can know why checking the driver version or if it stutters appears again.
Open Device Manager → right‑click the ethernet driver in network adapters → Properties → Driver → Roll Back Driver and follow screen instructions to get back to the stable version.

• Now, play your games

Note: This solution fixes the issue for most users, but not all systems respond the same. If you still experience stutters, lag, or audio glitches even after following this solution, the only reliable workaround is to disable the Realtek PCIe 2.5GbE Family Controller in Device Manager and use Wi-Fi instead.

13. AMD/Nvidia Stability Fix — Only For Those Facing Crashes (like Driver Timeout, etc)

Important prerequisite: First, open the case and reseat the GPU power cable, making sure the connection is secure at both ends (GPU and PSU) with no cable bending near the connector, then reseat the RAM and GPU in the PCIe slot properly. Now follow this step.

If you use an AMD GPU, all points are applicable. If you use an Nvidia GPU, skip the AMD‑only sub‑ section and start from “Stability steps for both AMD & Nvidia”. Apply each fix one by one, checking after each.

AMD‑only steps (Radeon users):

Follow Step 8 fully before continuing to ensure the crash fixes below work correctly.

• Disable Anti-Lag, Radeon ReLive features (especially Instant Replay) and Issue detection in AMD Software -
First, Go to the Gear icon then System tab → Disable Issue Detection Service (triggers false TDR timeouts/black screens).

Second, Gaming > Global Graphics → Disable Anti-Lag (causes insane stutters and crashes depending on game). If you want to use it, then test it per game. Keep it off globally.

Third, Go Record & Stream tab, then find and disable ReLive recording features like Instant Replay, Record Desktop, Streaming, etc. Instant Replay is particularly responsible for stutters, FPS drops, and driver timeouts.

•★★Manual Clock Tuning ( For All RDNA GPUs)★★ - AMD GPUs boost beyond their stable frequency due to automatic tuning or Hypr-RX, and lead to crashes and driver timeouts.

To fix this, open AMD Software → Performance → Tuning, switch to Manual Tuning (Custom), enable GPU Tuning and Advanced Control. Find your GPU’s official Boost Clock by AMD (e.g. 2600MHz for RX 6750XT) and use it as your Max Frequency, replacing higher default values like 2850-2900MHz or any factory overclock applied.

As for RDNA 4 Users: Set the max frequency offset to a negative value (like -300 MHz or lower). First, compare your in-game boost clock to the official spec for your GPU. Adjust the negative offset until the in-game boost matches the official value exactly.

Note- Per-game tuning overrides global settings when a per-game profile is created. Otherwise, global/manual settings apply by default. Always check for existing profiles and ensure this manual clocking setting is applied. Also, make sure Hypr-RX is turned off to prevent it from overwriting your settings. It can remain enabled in per-game profiles, so check the Gaming tab for previously launched games and disable it if needed. Then, test your system.

Stability Steps for both AMD & Nvidia:

• Disable iGPU (if present) - If your CPU has an integrated GPU, disable it in BIOS to prevent possible crashes or driver conflicts with your dedicated AMD GPU, especially during gaming and high loads.

• Disable HAGS - Go to Settings > System > Display > Graphics > Default graphics settings > Turn off Hardware-accelerated GPU scheduling > Restart. Recent newer drivers and games seem to be causing crashes when HAGS is on. Note- Nvidia users need it on for frame gen and enable it again if it doesn't fix your issue

• Disable hardware acceleration in Background Apps- If you have any apps that run in the background and support hardware acceleration, such as Discord, Game launchers or web browsers, disable this feature via their settings to prevent possible GPU conflicts.

• Ram Overclocking Adjustment (XMP/EXPO or Equivalent) - In BIOS, go to the memory or its overclocking section and test each XMP/EXPO (or its equivalent) lower memory profile one by one (e.g. 3600 MHz → 3200 MHz → 3000 MHz). If none work, disable memory overclocking and test again. if issue remains then restore your highest stable profile and follow below suggestions.

If the issue persists, update your BIOS (Step 4) and follow step 14. If problem still persist, check your setup as in Step 2, look for a failing PSU or loose cables, and note that unstable undervolts or overclocks can cause the same issues.

14. User‑reported rare or system‑specific Performance/Stability cause (Must check if above steps didn't fix your issue)

• Uninstall Your RGB softwares like Lian Li L-Connect 3, OpenRGB, SignalRGB, iCUE, Razer Synapse, Aura Sync, Mystic Light ,etc which have caused performance issues for many users) if using these RGB software or any other with compatible components, these can frequently cause 1% low FPS stutters, crashing and frame drops.

Not all but many cause same issue, so you must check and confirm by uninstalling it. Even on high end systems like Ryzen 9800X3D + RTX 5090, this was the cause of the performance issue.

• If your system has both HDD and SSD Windows automatically spreads the pagefile across both drives by default, this forces memory swaps to hit the slow HDD during gaming peaks, causing stutters/hitching even with plenty of free RAM.

To fix: Right-click This PC > Properties > Advanced system settings > Performance Settings > Advanced tab > Virtual memory Change > uncheck "Automatically manage paging file size for all drives" > select your HDD drive > choose "No paging file" > Set > then select your SSD > choose "System managed size" > Set > OK through all dialogs > restart immediately.

• If you installed Wallpaper Engine and it's running in the background (even paused) causes frequent stutters and performance drops for many gamers.

Close it via tray > Exit, then then check Task Manager (Processes tab) for any lingering "Wallpaper Engine" entries and End task if present. Now play your game. Do this every time if you still have Wallpaper Engine installed.

Additionally some users also reported, that adding per-game rules: In Wallpaper Engine Settings > Performance tab > Edit Application Rules > Create new rule for your game's .exe > Set Condition "Is running" > Wallpaper playback "Stop (free memory)". Also fix issue but thats not widely tested so not sure if it work for all.

• Disconnect unnecessary USB devices- If you see random crashes, reboots, or freezes, unplug non-essential USB devices/accessories (especially USB hubs, fans, or other powered devices) and test again, as a faulty and incompatible USB device or driver can sometimes cause system instability.

• DRAM-less SSDs Performance Issues- Some DRAM-less SSDs can experience performance drops under certain workloads, potentially contributing to game stutters. If you have one, then move Windows and games to a DRAM-equipped NVMe SSD, then temporarily disconnect the DRAM-less SSD (if you can) and retest. If stuttering improves or get fixed, investigate further and consider replacing the drive if necessary. DRAM-less SSDs do not inherently cause stuttering, so test before replacing.

• A silently failing, cheap, or aging display cable can cause microstutters only during gaming, making diagnosis tough. Users facing performance issues should Test by swapping cables as well as ports (HDMI to DP or DP to HDMI).
Also, the same can apply to faulty PSU cables.

15. Fix for users who are getting flickering, stutters, or crashes When alt-tabbing while gaming

MPO is a Windows feature aimed at improving rendering performance, but on some systems it used to cause some issues. This feature is now a key part of Windows 11, so DO NOT forget to re-enable it if it wasn’t the source of your issue.

Common issue linked to MPO is Stutters and frame drops ,when alt-tabbing persist for a number of users, especially on the latest Windows 11 builds.

NVIDIA advises disabling MPO for these issues, use their official method, which works for AMD too.

Here is the official link to do this: https://nvidia.custhelp.com/app/answers/detail/a_id/5157

16. Fix Thermal Throttling on Gaming Laptops

This step helps prevent overheating and extend component lifespan of Gaming Laptops. A trusted guide from the Acer Community works for all gaming laptops.

Important note to avoid confusion:
The Acer Community cooling guide applies to all gaming laptops. Steps 1 to 4 are less time taking and should be followed first. If overheating issues persist, continue with Step 5. While the Nitro 5 is used as an example there, the process is the same for other laptops, repasting and cleaning the cooling system by detaching the heatsink, and cleaning fans and vents inside and out. This is the only reliable fix for high temperatures.

Here is the Cooling guide here:
https://community.acer.com/en/discussion/724763/ultimate-laptop-cooling-optimization-guide

17. Fix Thermal Throttling on Gaming Desktops

Most people only check CPU and GPU core temps, but it’s just as important to monitor GPU VRAM (memory junction) and GPU hotspot temps, which can run much hotter and trigger throttling under heavy loads. NVMe SSD temps should also be watched separately, as they can overheat during sustained writes and cause sudden performance drops even when CPU and GPU temps look fine.

Critical Temperature Limits (Avoid Getting Close to These):

• CPU TJ Max: Intel 100 °C, AMD 95–105 °C (consider reducing it if it reaches the 90s)

• GPU Temp: NVIDIA 88–93 °C, AMD 100– 110 °C (consider reducing it if it reaches the 90s)

• GPU Hotspot/Junction (AMD & NVIDIA): Up to 110 °C (typically 10–30 °C higher than core temp). While the maximum operating hotspot temperature can be around 110°C, it's best to keep it below 100°C.

• VRAM/Memory Junction (AMD & NVIDIA): 95–105 °C is acceptable but should be monitored closely, as throttling usually begins at 110 °C.

• SSD Throttling: Begins at 70 °C, severe at 85 °C (though this varies by drive, it holds true for most models)

Monitoring Temperatures Effectively

• Use AMD/NVIDIA Software Overlay:
Use AMD Adrenalin or the NVIDIA GeForce Experience overlay to monitor CPU and GPU temperatures. Some versions also show GPU hotspot and VRAM/memory junction temperatures. If any readings are missing (e.g., GPU junction or VRAM temps), check the second method below.

• Second Good Alternative Method – HWiNFO:
HWiNFO provides full monitoring for CPU, GPU (including hotspot and VRAM), and all other sensors. For real-time monitoring, you can use HWiNFO’s shared memory feature with MSI Afterburner to display these stats directly in Afterburner while gaming. Alternatively, you can let HWiNFO run in the background, play your game, and check afterward—it shows average, maximum, and minimum temperatures. If you have a dual-monitor setup, keep HWiNFO open on the second monitor for live tracking.

• SSD Temperatures:
Run CrystalDiskMark benchmark and check or use HWiNFO while gaming. Note that speeds will reduce once the SSD reaches its maximum temperature limit.

Steps to Reduce Component Temperatures

• CPU Temperature Fix:

  • For AMD CPUs, Undervolt the CPU using PBO (Precision Boost Overdrive) to achieve lower temperatures.
  • For Intel CPUs, Use Intel XTU or Throttlestop to undervolt, which can help reduce CPU temperatures while maintaining stability.
  • Set an effective custom fan curve, it can make a significant difference, often reducing temperatures by 10°C or more while balancing noise and cooling.
  • If needed, clean dust from fans and vents, then reapply high-quality thermal paste to the CPU.
  • Further cooling improvements depend on your cooler.

• GPU, Hotspot & Memory junction temperature Fix:

  • Undervolting your GPU through AMD Adrenalin software can also lower power draw and temperatures without major performance loss.
  • Set an effective custom fan curve, it can make a significant difference, often reducing temperatures by 10°C or more while balancing noise and cooling.
  • If the issue persists, to effectively reduce GPU, hotspot, and memory junction temperatures, clean or remove old thermal pads/putty and apply new, high-quality thermal putty (more effective than pads). Also, apply high-quality thermal paste to the main GPU chip.
  • Further cooling improvements depend on your cooler.

• SSD Temperature Fix:
Install an NVMe heatsink (most modern motherboards include one, or you can buy aftermarket). Ensure case airflow reaches the SSD area, as poor circulation causes heat buildup.

[✓] Restart and You're Done! Time to Play.
If this guide helped you, please consider upvoting, sharing your results, or leaving a quick comment about what worked. It helps others and increases visibility in the community.


r/AMDHelp • • Aug 11 '16

Announcement Please make sure to flair your posts! Especially make sure to change the flair to resolved once solved!

160 Upvotes

Thanks guys.


r/AMDHelp • • 3h ago

Tips & Info How I fixed driver timeouts on 7700 XT

4 Upvotes

I recently started having the dreaded driver timeout issues that seem to be so common with these cards. It became unbearably frequent, I would get into a game and play for about an hour before it would crash. Sometimes it would crash within minutes of launching a game. Sometimes it would break windows explorer and give a black screen. More than a few times, it caused the entire system to freeze.

I did all the usual recommended items. Rolled back drivers, turned off overlays, plugged my second monitor into the onboard GPU instead. Nothing seemed to work. I started to suspect it was a hardware issue but the GPU isn't that old, and it had been working fine, so I wasn't ready to give up on it. After I performed these steps I was able to game for hours with no issues at all, and to date I have not experienced the issue. Hopefully this will work for others. Here are the exact steps I took:

  1. Performed full driver wipe with the AMD clean-up utility while in safe mode.
  2. Installed AMD Adrenaline 26.3.1 and turned off updates (check online for your GPU, I used Gemini to search the web for the drivers that were reported to work best for my GPU) and rebooted.

At this point, I immediately got the driver timeout message when Windows started. Thought it was odd because no game was running.

3. Reinstalled all of my system drivers, I went to my motherboard software center and downloaded everything that was available, this is what I suspect actually fixed the issue. The AMD Chipset drivers will use your CPU as cache for games, and without them, the load is entirely on your GPU, although I don't know for certain which item actually fixed it.
4. Rebooted PC

After I did this windows started with no timeout message, I launched a game with heavy graphics and played for about 5 hours with no issues at all. I hope this helps someone else. Best of luck!

Specs:

CPU: AMD Ryzen 5 7600X 4.7 GHz 6-Core Processor
GPU: ASRock Challenger OC Radeon RX 7700 XT 12 GB Video Card
RAM: Klevv CRAS V RGB 32 GB (2 x 16 GB) DDR5-6000 CL30 Memory
MOBO: ASRock B650M PG Lightning Wifi Micro ATX AM5 Motherboard
PSU: Corsair CX750M (2021) 750 W 80+ Bronze Certified Semi-modular ATX Power Supply


r/AMDHelp • • 5h ago

Help (GPU) My rx9070xt keeps Crashing

6 Upvotes

GPU keeps crashing during streaming – looking for advice
I’m having repeated crashes with my RX 9070 XT. During streaming, my screens suddenly go black, sometimes with blue/green lines, and the PC becomes unusable. It has also crashed while completely idle.
I’ve tried DDU, completely reinstalling AMD drivers, testing older driver versions(26.11.1 and 26.11.2), and disabling Windows automatic GPU driver updates. Stress tests seem to run fine without crashes.
Could this be a faulty GPU, VRAM issue, driver problem, or something else? Has anyone experienced something similar?
I have had the GPU since February and it had never caused me any problems. I have not overcooked it. It’s all still on its standard settings. Should I return to the older drivers like 26.8 or what should I do?


r/AMDHelp • • 2h ago

How I Fixed the LiveKernelEvent 141 Error

3 Upvotes

Hello guys!
A few days ago, I made a post about having issues with my RX 9070 XT, as I kept getting LiveKernelEvent 141 errors whenever I tried to play games.
Well, I’m happy to report that with driver version 25.5.2, the crashes have stopped!
Just wanted to share this as a tip for anyone experiencing similar issues. Hopefully, it helps some of you too!
Have a great day!


r/AMDHelp • • 2h ago

Crucial Pro OC 32GB DDR5 400MHz CL32 to 6000MHz CL30 with 7800X3D

2 Upvotes

Hey, everyone - just making this post to ask for some assistance with my RAM speeds on my 7800X3D. I know that running 6400MHz CL32 on a 7800X3D is generally quite unstable and will usually result in the memory controller going into 2:1 mode, so as a result I've been running my Crucial RAM with the EXPO II profile of 6000MHz CL36-38-38-44 to circumvent this. However, I was wondering if I could potentially get more out of this RAM by downclocking to CL30 from this EXPO profile but am unsure as to how to do it. I've seen that Micron dies are more difficult to tighten that Samsung and Hynix dies, but I'd like some insight into if it's possible. For example, what subtimings and voltage would I set? Should I start from the 6000 CL36 profile and tighten from there or the 6400MHz CL32 profile and downclock that? I've never done any manual tuning with RAM before so any help would be greatly appreciated. Thanks, guys!

Edit: title should be '6400MHz'.


r/AMDHelp • • 3h ago

Help (Software) League of Legends Causing Speed Lock on Ryzen 5

Post image
2 Upvotes

I have a Ryzen 5 3500U, and for the past couple of weeks, I’ve been having issues with LoL. For some reason, as soon as the game starts, it triggers a speed cap: no matter what I do, the entire system gets insta bogged down with CPU usage at 100%, and the clock speed never goes above the base frequency—in extreme cases, it doesn't even exceed 1.2-1.6 GHz. This makes the game practically unplayable, as I get no more than 20 FPS on idle, I’ve even been receiving LeaverBuster penalties because the client fails to load in time during the champion select, or the screen takes too long to open at the start of a match—resulting in it being flagged as an abandonment due to inactivity or the selection process becomes a form of torture, since even the audio stutters.

Tried with graphics set to the minimum, "the Potato" mode- low spec enabled, and the resolution at 720p. The GPU, meanwhile, seems to function normally and stays stable at around 60–70°C. (Thinking it might be thermal throttling, I applied new thermal paste, and cleaned all board Components but that wasn't the issue. As soon as I close the game—or run other titles—everything returns to relative normalcy with decent performance.) although at times it seems to persist, hovering between 1.6 and the base-speed limit [However, I went from games that ran at up to 240 FPS to an average of no more than 40.]

Changing power plans—even to "High Performance" mode—makes no difference. The Adrenalin — installer indicates that there are no updates available (version 26.5.2).
Windows is also up to date. (DISM and SFC running without errors)
I don’t use game optimizers or add-ons (not even the Xbox Game Bar, nor Discord or any overlays or recorders/streams).

System is not Overloaded (It never exceeds 4%—at most 10%—CPU usage when idle. even with local music and the browser open)

-I have a dual-boot setup with Linux (and it works fine in Linux So it doesn't seem to be a hardware issue, since—if I don't open LoL—the turbo speeds kick in and out and function normally. It happens whether the system has just started up or has been in use for hours.).

-Everything is clean; there are no Jack sparrow games/programs (everything is either free/open-source software from winget or comes from Steam). - In fact, I practically don't use Windows for anything other than playing LoL and L4D2.

-Lol +Vanguard, it was recently reinstalled (less than a month ago) due to unspecified [not listed] Vanguard error codes (there was a support ticket, and everything was fine until a few days ago - Another support ticket has been open since it started getting stuck, but there’s still no response.)

I tried changing some settings in Adrenalin, but to no avail (in one very isolated instance, toggling GPU scaling seemed to clear the freeze, but that only worked that one time). Resetting the graphics driver using the keyboard shortcut didn't help either—in fact, it made things worse; I even got kicked from a match because the screen didn't recover in time. Furthermore, there’s no difference whether I play using the built-in display or an external one.

I’m considering just reinstalling the entire system, even though it’s been less than 6 months since the last time I did it.

Any ideas?


r/AMDHelp • • 18h ago

Tips & Info Possible Driver Timeout Fix for others.

Post image
29 Upvotes

I am on a 5700x & a 9070xt.

I got the 9070xt in May 2026 & upgraded from a 3070.

I was not having any of the "driver issues" many folks have on WINDOWS with AMD GPUs.

Until drivers 26.10.1

I'd get random driver timeouts & game crashes with no error codes.

Typically 9070xt users don't benefit from the HAGS, disabling from what I could tell & I didn’t want to disable HAGS bc my setup is CPU bottlenecked. But after shader cache clear didn't fix it my issue & nor did full driver wipe (with DDU) I was willing to try anything. When I went to turn off HAGS I saw a VRR setting I had not seen before that I had a hunch could have been causing my crashes. I turned it off & all my crashes stopped. I should have posted weeks ago but forgot. But if anyone else is having inexplicable crashes & wants to give it a try it might work for you as well.

Display Setting -> Graphics -> Advanced graphic settings -> Variable Refresh Rate set to off.


r/AMDHelp • • 22m ago

Help (CPU) My cpu drivers Crash when i play gd

1 Upvotes

can someone help me is weird my cpu drivers Crash when i specifically geometry dash and whole pc goes black screen with audio loop in eventvwr It says

andryzenmasterdriverv20 could start propertly

Ryzen 7 5700G

i dont use the igpu IS disabled in BIOS and temperatures normaly dont go over 70

ram normaly 50-70% and gpu isnt overheating


r/AMDHelp • • 48m ago

Help (General) Fortnite fps stutters (help)

Thumbnail reddit.com
0 Upvotes

r/AMDHelp • • 1h ago

I have lenovo thinkbook 16 amd Ryzen 5 7535hs there is a problem of sound of chaar chaar when I open the laptop this sound happened very little low what to do

Thumbnail reddit.com
1 Upvotes

r/AMDHelp • • 9h ago

Help (GPU) New gpu

4 Upvotes

I upgraded from a 3070 to a 9070xt today and my pc has completely frozen twice while watching YouTube the freezing happened hours apart from each other and playing games was completely fine i checked event viewer and all it said was windows wasn’t shut down properly anyone know what could be happening yes i used ddu


r/AMDHelp • • 6h ago

Help (General) 5800x3d idle core voltage

Post image
2 Upvotes

Hello

I need help knowing if this normal and safe for a 5800x3d in the long run

I seen the voltage get up to 1.294 (peak voltage) and 1.280 (average voltage)in cinebench

Idle it sits around 1.256 to 1.261 with a random peak to 1.294 then back down to 1.256 area

In a multi core cinebench it sits around 1.237 with a peak of 1.245


r/AMDHelp • • 3h ago

Help (General) New AM5 build: slow BIOS fixed by a new motherboard, but Windows still freezes and NVMe resets (stornvme 129) keep climbing. What's next?

1 Upvotes

TL;DR: The 7800X3D build took 1-5 min to boot, with NVMe timeout errors. Swap testing showed the old ASUS board caused the slow POST. A new MSI board fixed the BIOS time, but Windows still hangs, apps show "not responding," and stornvme 129 events keep increasing. Before I reinstall Windows on a spare SSD, what would you check?
Specs (friend's PC, all bought new)
CPU: Ryzen 7 7800X3D
Board: ASUS ROG STRIX B650-A GAMING WIFI (BIOS 3881, June 2026, later updated)
RAM: Patriot Viper Venom 32GB (2x16) DDR5-6000 CL30, in A2/B2
GPU: Radeon RX 9070 XT
SSD: Klevv CRAS C910 1TB NVMe
Cooler: Thermalright Peerless Assassin 120 SE
PSU: MSI MAG A750GL PCIE5
Windows 11
My own PC is nearly identical (different RAM brand, CL30 6000 kit, different motherboard, different case, different cpu cooler, and we have the same ssd brand but instead od the 1tb version I have the 2 tb) and has no issues.
Original problem
Boots took anywhere from 1 min to nearly 10 min, with a long black screen before the ASUS logo, occasional sluggishness, and stornvme Event ID 129 ("Reset to device, \Device\RaidPort1") in Event Viewer. 27 events at first.
What I tried on the ASUS board
EXPO I / DDR5-6000: Last BIOS time ~57 sec. EXPO off (4800): ~9-10 sec.
Memory Context Restore = Enabled: boot hung on a black screen for 3+ min, and the BIOS then froze. Fixed with a CMOS reset.
Power Down Enable = Enabled: no change (56.7 sec).
Reseated the SSD: two 40-sec restarts at 4800.
OCCT memory test at 6000: 30 min, 0 errors.
CrystalDiskInfo: 100% health, 0 media errors.
BIOS updated.
Swap tests
Setup BIOS time
His board, his RAM, EXPO on 57 sec
His board, my RAM, EXPO on 33 sec
His board, my CPU + my RAM 38-39 sec
My board, his CPU + RAM + GPU + SSD 11.5-12.8 sec
My own PC (reference) ~11 sec
His parts were fast on my board. That pointed at his ASUS board for the BIOS slowness.
New board: MSI MAG B850 Tomahawk WIFI. BIOS flashed to version 7E53v1A44. After install: ~17 sec BIOS, ~45 sec to Windows. EXPO/A-XMP enabled.
What's still wrong
Windows has been slow or unresponsive in nearly every test: on his old board, with my CPU in it, on my board, and on the new board.
I reset the pc multiple times are changing the mobo, updating bios, making sure all drivers were installed and up to date, and making sure windows was up to date. Each time I restarted the pc it seemed as if the issues was fixed completely and there were no new 129 errors. Later on in the day though I get a call from my friend. Several apps showed "not responding" at once, and it wouldn't restart normally. I had to hold the power button.
The next boot sat at the spinner for about 5 min, then showed a grey screen with a cursor for a few minutes.
stornvme 129 count went 27, then 33, then 36, then 3 more after that. The clock is wrong since the board swap, so I can't trust the timestamps.
Other System log entries: DistributedCOM 10010, SCM 7009 and 7000 (services slow to start).
Where I am
Same Klevv SSD and the same Windows install through all of it. I have a spare WD SN7100 1TB.
Not yet done: fresh Windows on the SN7100 with the Klevv unplugged, and swapping in a same-model PSU.
I'd like to avoid a full reinstall, redownloading every game, and relogging into every app if there's a cheaper test.
Questions
Does this look like a bad Klevv drive, or something shared across every setup like the PSU or GPU?
Is a stripped-down test install on the SN7100 the best next step, or is there a quicker check?
Any known issues with this Klevv SSD on AM5 that I should look up?


r/AMDHelp • • 12h ago

Help (Software) Is Above 4G Decoding Re-Size BAR Support enabled?

Post image
5 Upvotes

CSM disabled

Secure boot enabled

I just don't know if auto is the same as enabled and so far performance is good in games like cyberpunk and battlefield.


r/AMDHelp • • 4h ago

Help (General) Enabling Global C-State, CPPC, disabling CPPC Preferred cores fixed my 5700x3d frametime spikes during 1% lows in Valorant, but how?

1 Upvotes

I tried switching GPUs from 6600 to 4060, tried different RAM and speeds and xmp profiles, tried scskiller or resolving shader issues, nothing seemed to fix my stutter in valorant during combat.

But after doing the steps above, BOOM THEY’RE ALL GONE. NO MORE STUTTERS

i want to know how following these steps solved my problem. Can someone explain?


r/AMDHelp • • 14h ago

Help (General) Fsr makes no difference for me besides a worse image quality

6 Upvotes

I'm new to amd i have a 9060 xt I've tried it on multiple games gears of war, 007 first light, forza horizon 6, there is no difference between fsr off or native and fsr performance just a worse quality same gpu usage same fps (edit) my cpu is an i5 14400


r/AMDHelp • • 4h ago

Help (Software) Cyberpunk is capped at 60 fps for some reason

0 Upvotes

I recently got a new PC (RX 9070 XT, Ryzen 7 9850X3D) which is pretty overkill but I cant seem to get the game to uncap 60 fps? doesn't matter if I make the graphics to low or high, its stuck at 60, I tried disabling Vsync, FreeSync, and other fixes people say online nothing worked, only thing that worked was enabling frame generation in game, which I really don't want to use, does anyone know what is the issue? (I also uncapped the fps cap in the game settings) Edit: solved, check comments


r/AMDHelp • • 5h ago

Game crashed twice due to low VRAM. My GPU has 16GB and it's only using 13GB of it

Post image
1 Upvotes

7800XT 16GB

6000MHz 2×8GB CL30

1080p max quality


r/AMDHelp • • 6h ago

Help (General) Is this normal for a 7900xtx XFX

Post image
1 Upvotes

Ive noticed something weird with my gpu wires and was wondering if this was normal. As you can see their seems to be two unconnected wire ends. Should i be worried?

Also if i do have to fix this could i also have some wire recommendations for my card(7900xtx XFX)


r/AMDHelp • • 7h ago

Help (Software) 9060XT 16GB Driver Issues,

1 Upvotes

I have problems with Gpu Drivers, Any stable version that could run both Valo and Apex without issues?

26.3.1 Crashes my Apex

26.8.1 to 26.9.2 Kills my driver while playing Valo (Black screen forcing me to manually shutdown, when reopening the driver's not working properly forcing me to do a safe boot to delete and reinstall my drivers)


r/AMDHelp • • 8h ago

Help (GPU) AMD Sapphire 7900 XTX PCB to Air Cooler Compatibility

1 Upvotes

Hey hey,

So Im looking at getting a 7900 XTX and the Nitro+ I was looking at has just sold and gone out of stock. There is another Sapphire card available, the Pulse, and I was wondering if the Nitro and Pulse PCBs are similar enough to be able to mod the Pulse with the Nitro cooler?


r/AMDHelp • • 8h ago

Low single core performance on ryzen cpu while using balanced power plan

1 Upvotes

can someone explain this. so i was wondering this for quite while now, why i have such low single performance on my ryzen 7 5700x compare to 3700x for example it was never pass 500 on single core even with pbo and stuff. long story short i tried power saving mode out of curiosity and boom i got 600 single core score.


r/AMDHelp • • 8h ago

Help (GPU) Need Help - GPU pad replacement.

Post image
1 Upvotes

ASRock Challenger 6600 Thermal Pad recommendations / Thickness

Computer Type: Desktop

GPU: RX 6600

CPU: RYZEN 5 5600G 6 CORE 12 THREADS

Motherboard: ASUS TUF WIFI II (B550M)

RAM: 32GB TRIDENT Z NEO 3600MHZ CL18

PSU: FSP 750W 80+ GOLD FULLY MODULAR

Description of Original Problem: Gaming on low-end games like (LOL, WOW, Dota) works fine but when playing apex crashes after a couple for minutes and needs a full PC reboot. Idle temps @ ~45 deg Celsius.

Troubleshooting: I've tried repasting but still crashes. Wanted to know if changing the thermal pads might help.