r/CarbonFiber • • Nov 20 '24

Is this real? posts....LOOK HERE BEFORE POSTING!

19 Upvotes

With new printing methods, the traditional fake CF that looks like it was printed in black and white, with no texture giving it a 3D look, it will be harder to tell. If a part is made perfectly, it won't have weave distortions, but that is rare. Also, look for parting lines, and fabric seams in logical places like edges. If it looks like someone just cut a sheet of plastic, then that seam will look exactly like that. Surface finishes also effect what you can see being real or fake. Matte finishes hide the high definition glare and weave diffraction.


r/CarbonFiber • • Feb 19 '25

For those looking for starter books!!!

21 Upvotes

I'll try to find a place to make a list, but I happened to see these two books in our library, so they might be a good starting place for those interested in composites, but have NO idea about it!!

Intro to Composites, 4th Ed, Composites Institute NYC. ci@socplas.org No ISBN

Composites - A design guide, Terry Richardson 0-8311-1173-9

Second is a bit older, but only the details change through the years.


r/CarbonFiber • • 1d ago

Carbon fibre fix

Post image
1 Upvotes

How do I fix this carbon fibre scratch
💔😭
Carbon fibre riser bar for a bicycle got scratched recently


r/CarbonFiber • • 3d ago

Ooh now that’s a reaction

Thumbnail
gallery
9 Upvotes

Hi Carbonners
I was going about my project of skinning a damaged car side skirt. I repaired the cracks with Kevlar tape and Epoxy. Filled and sanded the posh side and then after thoroughly cleaning with Acetone I set about laying a pigment coat to start skinning.
The epoxy is the same as I successfully used on the tape and the pigment was mixed to the correct ratio but unfortunately it has reacted badly. I am also not having to use a curing box to get the temperature up to 25 degrees centigrade but this also has been used throughout.
Where did I go wrong? And just as importantly what should I do to correct it?

My current plan is to go back and sand it back down and spray a coat of isolator before trying again.


r/CarbonFiber • • 3d ago

Is this pressure chamber could be suitable for carbon fiber manufacturing ?

Thumbnail
gallery
13 Upvotes

Hi! I’m looking for some professional advice. I have an opportunity to buy some old environmental testing equipment, and I’m wondering whether this pressure chamber could be suitable for carbon fiber manufacturing, etc. What do you think? The price is very low because it comes from a post-Soviet factory that will soon be demolished, and if I don’t buy it, the equipment will probably be destroyed too :(

Weight 8800 Kg
Dimantions: ~ 2m Wide x 3.5m Length
Produced in 1976 in DDR
Price less than 3K usd

I was also offered a thermal chamber with a maximum temperature of 130 °C. What do you think about it? Is it any good?

1000 L and 1245 Kg, also produced in DDR


r/CarbonFiber • • 3d ago

Looking for the Composites Materials Handbook

3 Upvotes

Hi, I would like to know if anyone here has a PDF copy of the CMH17 vol.3. Thankss


r/CarbonFiber • • 3d ago

Filar: Custom filament winding software

Thumbnail
youtu.be
2 Upvotes

r/CarbonFiber • • 3d ago

Carbon Wing Structural Adhesive

Thumbnail reddit.com
1 Upvotes

r/CarbonFiber • • 4d ago

Advice needed for making a larger chopped tow carbon fiber part with a 3D-printed compression mould

Thumbnail
gallery
13 Upvotes

Hey everyone!

I’m planning to make this part out of chopped tow carbon fiber using the Easy Composites beginner kit I bought a while ago. I’ve made a few smaller parts with it, but this would be my first larger project.

The part is approximately 200 × 500 mm, with a 3 mm thick main plate and raised edges up to 10 mm thick.
I’ve designed a compression mould that I plan to 3D-print in PETG. I’ve added draft angles and fillets wherever possible and will pay attention to the print orientation to make demoulding easier (learned that the hard way…).

My plan is to orient the mould with the flat plate facing upwards and press the upper mould half down into it.

I have a few questions:
Mounting holes: Is there a good way to integrate the holes directly into the mould? I could drill them afterwards, but their positioning needs to be quite accurate.

Fiber-to-resin ratio: I’m concerned that the thicker edges won’t compress properly, potentially resulting in too much resin in those areas. How would you approach this? I also considered making the 3 mm plate and the raised edges separately and bonding them together, but I’m unsure about the strength of the bond.

Other potential issues: Do you see any problems with the design or manufacturing approach that I might be overlooking?

Any advice or suggestions would be greatly appreciated. Thanks!


r/CarbonFiber • • 5d ago

设计油冷eVTOL或高速电机

Post image
2 Upvotes

r/CarbonFiber • • 6d ago

CF pickleball paddle

Thumbnail reddit.com
0 Upvotes

r/CarbonFiber • • 6d ago

Spread tow carbon drape

Thumbnail reddit.com
1 Upvotes

r/CarbonFiber • • 7d ago

Imperator 108i

Thumbnail
en.wikipedia.org
1 Upvotes

An unusual car with a fiberglass body.

https://en.wikipedia.org/wiki/Isdera_Imperator_108i


r/CarbonFiber • • 7d ago

How can I repair this

Post image
2 Upvotes

Finally got my hood in after 2 years of waiting but has damage on the corners wats the best way to go about repairing the corners?


r/CarbonFiber • • 8d ago

PVA vs. no PVA

1 Upvotes

I'm making an airplane wing with two top and bottom female moulds. I applied 5 layers of wax and buffed between coats. Should I apply PVA, and if so how many coats? (I don't have a sprayer)

I would strongly prefer not to treat my surface after demolding want to transfer the mould finish.


r/CarbonFiber • • 9d ago

How can I fix this ?

1 Upvotes

Hello guys these were matte finished so I sanded down and applied 2k clear coat about 2 months ago. They were looking great. But yesterday I realised that there is something on them. I dont know what it is but you can hear it on the video. Its something solid. When I rub my fingers or apply ipa it becomes sticky but cannot take them off at all. Probably there was something on the road sticked to them. Idk.

Tried
- IPA - wont take off and spreads it.
- tar remover didnt took it off did nothing really
- vinegar did nothing
- warm soap water ofc didnt do anything

Since its becoming gummy on my fingers would it be best idea to polish them - idk too.

Any suggestions on what to do ?


r/CarbonFiber • • 9d ago

I got so mad I ripped carbon fiber

Post image
0 Upvotes

r/CarbonFiber • • 10d ago

Cons of fake Carbon Fiber

0 Upvotes

Hello everyone, im thinking of buying a front lip and spoiler for my car and im thinking just buying both of them fake Carbon fiber, I just wanted to ask before purchasing them what are some problems or cons that i could run into from buying them? Like will they look weird after a while or will heat ruin them?

If theres lots of potential problems might just buy in glossy black instead

Thanks


r/CarbonFiber • • 11d ago

Carbon fibre good fitment

Post image
1 Upvotes

Any ideas on how to make the hood fit better or am I just unlucky with the hood I got


r/CarbonFiber • • 11d ago

Beginning of tests Carbon Fiber cases of pitaka.

0 Upvotes

Beginning of tests Carbon Fiber cases of pitaka. I have now and will receive some more cases and make soon full tests review


r/CarbonFiber • • 13d ago

Best plan of attack to restore frame covers?

Thumbnail
gallery
6 Upvotes

Ilmberger carbon fiber frame covers. These are normally about $600 new from Germany and I got these for $150 from a crashed BMW S1000RR parts lot. Planning on using these for my ‘17 S1K.

Appears to be some fade, a hole, and a medium sized dark spot. I have yet to receive them but plan on trying to restore them as a DIY project. I’m not looking for perfection but definitely trying to give them some more life.

Thanks for any tips!


r/CarbonFiber • • 13d ago

Impact jante carbone

Post image
0 Upvotes

Je vais troquer mes jantes alu contre des jantes carbones et j'ai déniché une bonne affaire sur lbc.

Malheureusement, la roue avant a pris un pet (le vendeur pense que ça vient d'un cailloux en roulant).

Est-ce que un red flag ou bien je peux y aller ?

Merci d'avance !


r/CarbonFiber • • 14d ago

Hi, does this seem fixable?

Thumbnail
gallery
10 Upvotes

I am planning on buying this trunk and getting the clear coat redone by a shop. I am wondering if the fiber is damaged beyond saving, or it should look good with a new clear. The owner states it is a Vis Racing. In the last two photos the trunk is wet. Thank you!