r/Diesel • • 5h ago

The 6.7L Cummins "Killer Grid Heater Bolt": Do this 10-second wiggle test before it drops into Cylinder 6

Thumbnail
autozonic.com
14 Upvotes

If you run a 2007.5 through 2024 RAM 2500, 3500, or Cab Chassis with the 6.7L Cummins, there is a known mechanical vulnerability in the intake that routinely turns into a fifteen-thousand-dollar crate engine swap. Unlike Power Stroke or Duramax V8s that use individual glow plugs, Cummins relies on an open-element grid heater plate sitting directly between the intake horn and plenum. That heating grid pulls nearly 200 amps during cold start pre-heat and post-heat cycles. Over years of thermal shock and inline-six engine vibration, the insulating washer around the positive electrical stud breaks down and starts micro-arcing. Once that connection gets loose, heat spikes hot enough to melt brass, and the internal steel retaining nut backs off the threads right inside the intake channel.

Due to the airflow aerodynamics of the 6.7 plenum, that loose nut gets pulled straight into the rearmost intake runner: Cylinder Number 6. At highway speeds and 17.3 to 1 compression, the piston hammers that steel nut against the cylinder head, gouging the piston crown, snapping intake valves, and scoring the cylinder wall down past repair limits. A lot of owners assume they are protected because their dealership performed Safety Recall 67A (NHTSA Campaign 23V-116), but that recall only replaces the solid-state relay to prevent key-off electrical fires. It does not touch or upgrade the fragile factory stud and nut assembly inside the intake tract.

Whenever your truck is completely cold, take ten seconds to do the physical wiggle check. Put your fingers on that positive terminal post on the driver-side intake plenum and check for any axial play or rotational wobble. If it moves even a fraction of a millimeter, that nut has started unthreading and the truck should not be driven until it is addressed. Also keep an eye out for soft or intermittent P2609 trouble codes, which are often caused by terminal resistance spikes right before structural separation. If you want permanent peace of mind, ditching the stock plate for a solid billet delete like a Monster-Ram or BD plate removes the drop hazard completely.


r/Diesel • • 2h ago

6.9 idi with s366

5 Upvotes

Smokes until the turbo spools, Egts run way cooler than when it was non turbo and it accelerates a lot better.


r/Diesel • • 1h ago

Stealth vs full delete

3 Upvotes

What are the pros and cons of Full delete (removing everything) vs leaving it look stock (stealth delete) and is one better than the other?


r/Diesel • • 2h ago

6.9 idi with a s366sxe

1 Upvotes

Still has stock pump and injectors, just have the fuel screw turned up. Needs more fuel but it’s still way better than when it was non turbo.


r/Diesel • • 15h ago

6.5 Detroit turbo diesel

6 Upvotes

Anyone got like a master list to bullet proof these bad boys?


r/Diesel • • 9h ago

2012 LML white smoke, bad fuel?

1 Upvotes

2012 LML deleted and tuned. Recently filled up from an auxiliary diesel tank.
Started with light white smoke at idle and black smoke on acceleration. Now it’s only white smoke, even when warmed up, and gets slightly thicker under hard acceleration.
Truck idles smooth, no noticeable misfires. Haven’t checked the fuel filter yet.
Anyone had something similar?


r/Diesel • • 23h ago

Which M57 variant is the most reliable

5 Upvotes

Yes I know the M57 is one of the most reliable bmw engines. But is there any M57 variants that are less reliable? Maybe the smaller 2.5l I6 or are they as reliable as the 3l ones.


r/Diesel • • 2d ago

Meta Diesel continues getting the short end of the stick.

Post image
463 Upvotes

While gasoline dips in price, diesel prices stay firm.

Brought to you by r/GMDetroitDiesel


r/Diesel • • 19h ago

Question/Need help! New turbo time!

Thumbnail reddit.com
1 Upvotes

r/Diesel • • 20h ago

Purchase/Selling Advice C12 Oil Leak

Thumbnail reddit.com
1 Upvotes

Looking to purchase a truck with a C12 in it. Its several hours away and I made the trip to go take a look the other day. Luckily, the truck had not been washed down before I got there so I could see it in its natural state.

Its got 475k on the engine, runs and sounds great, coolant and oil are not contaminated. This is going to be my first truck.

This thing is soaked with oil on the entire bottom third of the engine front all the way to the PTO. I cant find where the heck its actually leaking from. Is there a gasket at the front of the motor that would equally soak both sides? It doesn’t appear to be from a hose or breather tube. It is enough that a crossmember has oil sitting it. Doesn’t look like its from the rear main seal.

Im hoping someone here is more familiar with common issues with this engine.


r/Diesel • • 1d ago

Meta Thoughts about new hybrids getting very similar if not better fuel economy than a diesel?

Post image
5 Upvotes

Modern hybrids drastically reduce if not eliminate the fuel economy advantage diesels had

If a hybrid can get 5.8l/100km (40 mpg) and so can a diesel but diesel is 40-80% cheaper, then diesel is the worse option

They also don’t have emissions equipment and maintenance is cheaper on them


r/Diesel • • 1d ago

Show off your build Om602.982 190k kms

5 Upvotes

Just swapped my sprinter engine om602.980 with 700k kms to this new om602.982 from the car version, changed all components and accessories from the old motor to the new one.

How it sounds?


r/Diesel • • 1d ago

2020 Silverado 2500HD Diesel

Thumbnail reddit.com
1 Upvotes

r/Diesel • • 2d ago

Question/Need help! Just bought my first vehicle/truck!

5 Upvotes

So I just bought higher mileage 2021 Silverado 1500 Duramax with the 3.0L Diesel engine. I know it’s got mixed reviews but I don’t care so far I love it. I need advice on what are some mods/ accessories I need? Also are fuels additives worth it? And if so what brand? Is there any other tips or tricks I should know that are useful or just helpful? TIA for any advice.


r/Diesel • • 1d ago

At what point does one need new tuning?

0 Upvotes

6.4 powerjoke currently has MiniMaxx V2

Truck has had weight reduction surgery. Truck also has a FASS 165 and an S&B air intake. Planning on putting a 4 inch down pipe back exhaust on it next year. I never run it higher than the stock tune. Since I’m planning on updating the exhaust more, should I get new tunning after that or are my modifications not enough to really worry about updating my tune?


r/Diesel • • 2d ago

OM602 hard to start after sitting for a while. After a few minutes sitting, bubbles start to go up this hose (i suppose it's the fuel pump supply line). Hose from lift pump side has no leak or bubbles.

Post image
2 Upvotes

r/Diesel • • 2d ago

Nissan X-Trail T30 2.2 dCi (YD22DDTi) - Looking for Single-Mass Flywheel Conversion or Alternative Donor Flywheel

1 Upvotes

Hi everyone!

I own a 2009 Nissan X-Trail T30 2.2 dCi 4WD (YD22DDTi) and I'm looking to replace the original Dual-Mass Flywheel (DMF) with a Single-Mass Flywheel (SMF).

I've been researching conversion kits and found the Xtreme Outback FNI193C / KNI24549-1A conversion, which seems to be designed for my engine.

Unfortunately, I can't source this kit or flywheel where I live (Tunisia).

I'm therefore trying to find alternative solutions, especially from people who have performed this conversion themselves.

My target specifications:

- Single-Mass Flywheel (SMF)

- 240 mm clutch diameter

- Flat friction surface (0 mm step)

- 24 splines, approximately 25.4 mm hub diameter

- Push-type clutch actuation

- 8 crankshaft mounting bolts

- M12 × 1.25 crankshaft bolts

- Heavy-duty sprung organic clutch

Questions:

  1. Has anyone with a T30 2.2 dCi YD22DDTi installed an SMF conversion?
  2. Are there conversion kits from other manufacturers besides Xtreme Outback?
  3. Has anyone successfully adapted a flywheel from another Nissan model, such as the Almera Tino, Almera N16, Navara D22 or Primera?
  4. Are there other donor vehicles with compatible crankshaft mounting patterns and flywheel dimensions?
  5. If you used a custom-machined flywheel, what specifications and modifications were required?

I'm particularly interested in real-world experiences, part numbers, donor vehicle models and photos.

I don't necessarily need a direct bolt-on solution. A professionally engineered alternative would also be interesting.

Thanks in advance! Any technical information would be greatly appreciated.


r/Diesel • • 2d ago

Question/Need help! Smoking Deleted L5P

0 Upvotes

TL;DR – my deleted L5P smokes and stinks and nobody can seem to figure out why.

I’ve posted in a few other subs with no luck so far, so here goes.

The truck: 2021 GMC Sierra 2500 Denali, 6.6L L5P.

Pre-delete: After the warranty ran out I put a shift on the fly tuner from Calibrated Power on it. I ran that on an otherwise stock truck from about 75K to 180K miles without any issues. I later learned that tune wasn’t letting the truck regen like it should, so that could be part of the puzzle.

The delete: Around 180K I did a full delete: cats, EGR, downpipe, the works, with a 4" exhaust. The ECM was flashed and tuned by DieselR. My first mistake was letting a friend’s son do it. he has a professional shop, but he’s young and a little inexperienced. he had enough history that i figured i’d let him do it.

First sign of trouble: About 2 hours into the drive home I stopped for fuel. i usually leave it running while i pump, and i saw big plumes of blue/white smoke coming out of the exhaust. I texted him and he said that was just soot burning off because the truck hadn’t regen’d in so long (see the Calibrated Power issue above). I didn’t love that answer, but I drive a lot so I figured it would clear up. it never did.

Shop #1 (the installer): A couple weeks later I took it back to him. after three weeks he still couldn’t fix it, and he blamed a turbo leaking oil. i didn’t buy that, so i picked it up.

Shop #2 (bona fide diesel mechanic): He had it for almost a month, mostly because DieselR is spread too thin in my area and kept missing appointments at the shop. Great mechanic. He also thought it was the turbo, and even though I didn’t agree I told him to go for it. He put in a refurb turbo, and lo and behold, it didn’t fix anything. Next he wanted to do a compression test for the head gasket. i passed on that. He was pissed he couldn't figure it out and didn't charge me a dime because "[I] didn't fix anything."

Shop #3 (mechanic I’ve known for ages): He scoped everything and said there’s no way it’s a head gasket because none of the symptoms point that way.

Shop #4 (local delete guy with great reviews): He got me in within a week and found:

+ NOx sensor that still had power going to it and hadn’t been deleted

+ DEF injector that also still had power and hadn’t been deleted

+ low DEF warning on the cluster that nobody else, including DieselR, had been able to clear. he cleared it.

He also floated turbo/head gasket at first, but after I gave him the full history he suggested putting his own tune on in case DieselR had left some glitch behind. that’s installed now, and I still have the smoke and the noxious smell. it’s not black and it’s not white, more of a blue/grey. he’s scratching his head too and thinks it might be a bad muffler (no idea what the first guy put on, could’ve been used) or back pressure from the 4" pipe.

Here’s the kicker: if i’m idling in park with my foot OFF the brake, it smokes like a freight train. when i put my foot on the brake, the engine audibly changes pitch and the smoke stops. take my foot off and it starts smoking again.

My theory: something got missed in the tune, or in how the TCU talks to the ECU. i’m no mechanic and i’m no tuner, but it really feels like it’s running way too rich at idle.

Hoping someone here has seen this before and knows the fix, or can point me somewhere besides the usual turbo/head gasket diagnosis.


r/Diesel • • 3d ago

Question/Need help! More Air, Less Coal

Post image
13 Upvotes

Just installed the stage two really fab custom intake kit into my L5 P. Does it make sense that I’m hearing more of the noise of the turbo inside the cabin and also that I noticed less coal
Could it be because of the larger air that the engine is breathing in?


r/Diesel • • 2d ago

5.9l 12v What weight oil should be used?

2 Upvotes

Manual says to use 15w40, AMSOIL says to use 5w40.


r/Diesel • • 3d ago

Deleted truck - DPS Texas

6 Upvotes

In Texas can you get a ticket for having a deleted truck? Will the state troopers check to make sure you still have egr etc..?


r/Diesel • • 2d ago

LARGEST AMERICAN BUILT SUPERYACHT

0 Upvotes

r/Diesel • • 3d ago

EMD G26 diesel cold start compilation

Thumbnail
youtu.be
4 Upvotes

Hey everyone,

For those who appreciate classic American diesel-electric engineering in Europe, I made a special edition compilation featuring every EMD G26 (Slovenian Railways class 664, nicknamed "Regan") start-up I’ve captured so far.


r/Diesel • • 3d ago

Question/Need help! M9R 2.0 dCi – Three injector leak-off rails leaking at the hose fittings

Post image
3 Upvotes

URGENT: Looking for some input from diesel technicians familiar with Renault/Nissan M9R common-rail systems

My 2016 Qashqai+2 2.0 dCi 150 hp has a strange recurring issue: three different injector return/leak-off assemblies have leaked fuel at the hose connections.

Here's what happened:

  • The original factory-fitted assembly started leaking.
  • I replaced it with a genuine/OEM assembly equipped with a mechanical back-pressure valve, reportedly rated at 10 bar, designed to maintain pressure in the injector leak-off circuit. It worked perfectly for approximately 200–250 km before leaking.
  • I then fitted an aftermarket assembly without a valve as a temporary replacement. That one started leaking after roughly 190 km.

With the aftermarket assembly, the engine also loses power under sustained load, particularly around 130 km/h. Power temporarily returns after reducing the load. Probably that's due to the non-existence of the back-pressure valve.

The engine's starting issues have also progressively worsened over time.

I haven't performed a return-circuit pressure test yet, so I don't know whether the system is actually experiencing excessive backpressure.

A few questions for diesel specialists:

  1. Could excessive injector return backpressure cause repeated leaks at the leak-off connectors?
  2. Could a restricted return line or excessive injector leak-off create this condition?
  3. Is a calibrated backpressure valve required on this particular M9R injector configuration?
  4. Could the missing valve on the aftermarket assembly explain the power-loss symptoms?

I only know the engine code (M9R), not the exact injector part numbers.

I'd appreciate any advice on the proper diagnostic procedure before replacing more parts.