r/FSAE • • 1h ago

Marketing Melbourne University Racing - Reveal Video

25 Upvotes

After a year of design and manufacture, Melbourne University Racing reveals it's 2026 competitor...

We spent a lot of time, love and effort creating the launch night video which leads up to the car reveal, which you can watch on our Youtube.

Directed, edited, and filmed by Sugeesh Atapattu
Visual effects by Andrew Yu & Gus Manners


r/FSAE • • 12h ago

Creating body panels from old frame CAD

Post image
8 Upvotes

Hi folks,

I am working off of an old CAD model of our team's frame (imported to OnShape). I am trying to design body panels that closely follow the metal members. What would y'all recommend to be the easiest way to go about it? Thank y'all.


r/FSAE • • 1d ago

Tire surface envelope

3 Upvotes

Hi there! mexican team here. We would also like to confirm our interpretation of Rule F.1.14 (Tire Surface Envelope), since it affects the packaging of our intake system under IC.1.2:

  1. Side view: Is the envelope bounded by lines tangent to the top of the Main Hoop and the outside diameter of the front and rear tires?
  2. Front/rear view: Is it bounded by lines from the top of the Main Hoop to the outer edge of the left and right tires?
  3. Reference point: Should the top of the Main Hoop be taken as the highest outer surface of the tube?

r/FSAE • • 1d ago

Brake calculations

4 Upvotes

Hello everyone!

I'm currently working on the brake calculations for our Formula Student car, specifically sizing the master-cylinder bore diameters. I'm a little unsure whether my methodology is correct because I haven't found many resources that explain the complete calculation process from start to finish.

My approach so far has been:

  1. Calculate the required braking torque at each wheel.
  2. Determine the required hydraulic pressure using the caliper piston area, brake pad friction coefficient, and effective disc radius.
  3. Calculate the force acting on each master cylinder using the driver's pedal force, pedal ratio, and balance-bar force distribution.
  4. Use the hydraulic pressure relationship (P = F/A), along with the circular piston area equation (A = pi*D^2/4), to calculate the theoretical master-cylinder bore diameters.
  5. Compare the theoretical diameters with commercially available master-cylinder sizes and select the closest options. My calculated diameters were slightly lower than the available options, so I chose the closest options (3/4 inch for front, 1 inch for rear).

Does this approach make sense? Am I missing any important steps or making incorrect assumptions, particularly when calculating the force applied to each master cylinder through the pedal ratio and balance bar?

I'd really appreciate any feedback, references, or examples of complete Formula Student brake-system calculations.


r/FSAE • • 1d ago

Rear Wing design

4 Upvotes

I've made a 3 wing rw, all 3 composed of E423 airfoil profiles and somehow its been my best one yet. Any recommendations for further improvements to the design of the endplates, or different airfoils or such?


r/FSAE • • 1d ago

Off Topic / Meta Aerodynamics in My Godot Vehicle Simulator

Post image
0 Upvotes

Hello Everyone! I come here with a weekly update on my Vehicle Simulator. I have made a massive improvement of adding basic aerodynamics and fixing a major bug that also helped contribute to the addition of this major feature.

I made a video here to showcase the update. Although it is not in-depth, I try to make these videos to showcase the progress of the project.

Video: https://youtube.com/shorts/cabqkj8rck8?feature=share

Drop a star on Github, it supports the project a ton!

GitHub: https://github.com/kakoiihito/Shift


r/FSAE • • 1d ago

Question Rotobox carbon wheel dimensions?

3 Upvotes

Hey, anyone here running Rotobox carbon wheels on their car? We’re thinking about them for next season but can’t find any real dimensions online, and Rotobox hasn’t gotten back to us yet.

Mainly need offset, PCD/bolt pattern, inner barrel profile and weight so we can check if they’d even fit our uprights and brakes. A drawing or step file would be amazing if someone has one lying around.

Also would love to hear how they held up if you’ve used them.

Thanks!


r/FSAE • • 2d ago

I asked Oxford Brookes’ Formula Student lead how students turn project experience into motorsport jobs

21 Upvotes

Hi everyone, I recently interviewed Professor Gordana Collier, who leads the Formula Student programme at Oxford Brookes alongside her role as head of school.

One practical suggestion stood out: bring a component, drawing or something you’ve made to an interview. It gives you a way to explain your own engineering decisions, what went wrong and what you learned.

We also discussed letting students make mistakes, involving first-year students, the electric and autonomous teams, and how placement experience changes students when they return.

Sharing it here because those parts may be useful if you’re trying to connect your Formula Student work with your next career step.

Full interview: https://www.youtube.com/watch?v=LPIZAYfweQo

P.S. This was my first interview of this kind. I learned a lot, and there are definitely things I’ll do better next time.


r/FSAE • • 2d ago

TC CHARGER 6.6KW - CAD

0 Upvotes

Hello everybody, we are using for the first time HK-LF-540-14 6.6kW TC Charger,
We are looking for a 3D model/CAD to implement it in our charging cart.

Does anyone have the CAD for this charger or a similar one?

Thank you!


r/FSAE • • 3d ago

Question Carbon Wing Structural Adhesive

5 Upvotes

To the teams that make hollow carbon fiber wings, what adhesive do you use to join the skins and spars together? There's a ton of options, from easycomposites to 3M to generic home depot stuff, but I'm curious what other teams use. The biggest thing I'm trying to keep in mind is cost, but I don't want to get the cheapest stuff I can find and then the wing breaks. Thanks!


r/FSAE • • 3d ago

Question Motor Shaft Load Analysis

Post image
7 Upvotes

Hey guys I am working on my first year team’s shaft meant to connect to Emrax 228 MV. I am working on identifying load cases on the motor shaft to find a factor of safety. I have some initial calculations but I am not sure about the reaction forces at the motor connection and the boundary conditions. The Shaft is bolted to the rotor so does that mean I should model that connection as a pin or fixed one. This is also to find the load on the bearing for sizing purposes. In extension I also want to identify the load cases for the motor mounts . Also we are looking to but motorcycle sprocket, have you guys had issues with making the spline the shaft?


r/FSAE • • 4d ago

3DSusp Web: Beta 2.0 is out!

Thumbnail
gallery
25 Upvotes

3DSusp Web keeps evolving! The latest updates introduce powerful new features, enhanced modelling capabilities and greater flexibility throughout the suspension design and analysis workflow.

Here’s a quick preview of the new features:

  • Custom reference frames and selectable measurement units
  • New tyre & wheel editor
  • STEP geometry import in the wheel reference frame, with clash detection (useful for electric in-wheel motor)
  • New Clash Mode for detecting component interference
  • Coil-to-coil contact detection for main and heave springs
  • Enhanced reporting tools
  • Customisable output selection, with configurations that can be saved and reused

And much, much more!

Access is free for FSAE/Formula Student teams. Simply register using your team's official e-mail address to start using the platform:

https://www.bspokeautomotive.it/3DSuspWebBeta/

We hope 3DSusp Web will become a valuable tool for your suspension development.

The development team.


r/FSAE • • 4d ago

Question First-year FSAE team – looking for feedback on our chassis design

Thumbnail
gallery
25 Upvotes

Hi everyone!

We're a first-year Formula Student team preparing for FS UK, and this is our first spaceframe chassis concept.

We'd really appreciate some feedback from experienced teams:

  • Any obvious issues with our triangulation or tube layout?
  • What would you improve in the overall design?
  • Any advice before we move on to detailed design and manufacturing?

We're still learning, so any criticism or recommendations are welcome!

Thanks!


r/FSAE • • 3d ago

Alternatives to Unitek Bamocar D3 700/400 or experiences with custom inverter design for EV?

4 Upvotes

Hi everyone,

Our team is currently using the Unitek Bamocar D3 700/400 inverter for our electric formula vehicle. We are looking into potential upgrade or replacement options that are reliable and widely used in student competitions.

  1. Are there any recommended commercial alternatives (such as Cascadia Motion PM100DZ or others) that offer good integration and support?
  2. For teams that have designed and built your own inverters from scratch, could you share some insights on your hardware architecture (e.g., SiC MOSFET selection, busbar layout, and control board setup)?

Any advice or shared experiences would be greatly appreciated. Thanks!


r/FSAE • • 4d ago

How do you set torsional and bending stiffness targets for an FSAE spaceframe chassis?

14 Upvotes

Hi everyone,

Our Formula Student team is in its 2nd year, and we're building a tube spaceframe chassis. We're starting our chassis FEA and I'd like your advice on target setting.

Context:

- In our first year, we collected stiffness targets from other teams and used them as reference (the average) as our own.

- The judges told us to define our own proper, well-justified targets.

Question:

How do you set your torsional and bending stiffness targets? What do you base them on?

Thanks a lot for any help or resources!


r/FSAE • • 3d ago

hi guys, need some help in starccm

0 Upvotes

so as part of my grad project I am supposed to validate Ahmadbody and perform a mesh dependence study for it so that I can use those sizings on my uni's Formula Student team's car. anyway, when i only activate surface mesher for the Ahmadbody the quality is fairly good (about 0.25 on average), however, when i activate prism layer meshing, the quality drops to E-5 or some stupid number like that. any idea why the quality drops so bad?


r/FSAE • • 3d ago

Chassis Manucturing using ERW tubes

1 Upvotes

Hi guys, we are planning to participate in Formula student UK this year and now we are searching about suitable steel grade for our chassis.

In my country, Seamless tubes are difficult to source and what we find is the ASTM A106 grade B. Which is the highest yield strength material we could find( for seamless tubes)

Another option we have is to use ERW tubes with minimum yield strength material of 235 MPA.

So my questions are if we use the ERW tubes without doing any physical testing to prove equivalence, will we pass scrutineering?

And in the calculation in SES can we use the numbers specified in the rules for calculating ( minim yield strength= 305MPA) or should we stick with the 235 MPA


r/FSAE • • 4d ago

How to change ramp angles on a Drexler V2 LSD?

1 Upvotes

Hello everyone,

We currently have a Drexler V2 LSD on our team, and we want to adjust the ramp angles for our setup, but we're not exactly sure how to do it. Is there a manual on how to adjust them?


r/FSAE • • 5d ago

Competition FSG to no longer use a quiz for registration

Post image
197 Upvotes

r/FSAE • • 4d ago

Question When do individual team members need to sign up (UK)

0 Upvotes

Hi I am apart of a new team that is doing concept class. I manage the recruitment and handling of all applications for my team.

I am aware that all team members must be an IMechE member. They must also all individually sign up. However I do not know the deadline for when all team members must sign up.

I need to know this information as soon as possible because we are ending recruitment this Friday and I’m sending every email to new members instructing on what they must do. I want to include deadlines.

I have look for hours but cannot find nothing but the ai response on google (which isn’t always accurate).

Any help will be much appreciated


r/FSAE • • 5d ago

Question Tab washers

Post image
16 Upvotes

Does anyone know if these are legal for positive locking and if so, have insight on their use?


r/FSAE • • 5d ago

Taylor Race 20T tripod and axles

1 Upvotes

Hello everyone, anyone has some data on the maximum torque allowed by the TRE tripod and axle? Thanks


r/FSAE • • 5d ago

Formula Student headrest – how do you attach the foam and cover to the mounting plate?

1 Upvotes

Hi everyone!

I'm working on the headrest design for our Formula Student car, and I'd like to know how other teams manufacture and assemble theirs.

Our current design has a metal backing plate attached to the chassis. We are looking for a reliable way to attach the foam padding to this plate.

I've seen different approaches used by other teams, such as:

  • Using hook-and-loop (Velcro) to attach the padded assembly to the metal plate.
  • Using adhesive or other mechanical fasteners.

I'd really appreciate it if you could share how your team does it.

A few questions in particular:

  • Do you attach the foam directly to the metal plate, or do you use a separate backing?
  • How do you secure the whole assembly to the mounting plate?
  • Have you had any issues with Velcro, adhesives or mechanical fasteners during technical inspection or testing?

Pictures of your setups would be especially helpful!

Thanks in advance!


r/FSAE • • 6d ago

How To / Instructional 1st Year team need advice

6 Upvotes

Hi everyone,

We are a brand-new, first-year Combustion Vehicle team preparing for Formula SAE Italy 2027 (still deciding between entering Class 1 + Class 3 or starting with Class 3 only).

Right now, we are struggling to establish a clear, structured engineering workflow. We’ve read through the rules and searched past threads, but we are still unsure about the exact sequence of early design decisions.

Any advice on a realistic first-year roadmap, common pitfalls to avoid, or recommended foundational resources would be hugely appreciated.

Additionally, we’ve heard that some alumni and experienced members occasionally mentor newer teams. If anyone is open to offering occasional guidance or reviewing our early progress, we would be honored to connect.

Thank you all in advance!