Hi everyone,
I'm looking for help diagnosing an issue with my 2023 Fisker Ocean Extreme AWD (approx. 73,210 km / 45,491 miles).
1. What happened
The vehicle was working normally. I charged it overnight at home using my AC wallbox (11 kW). The HV battery was fully charged.
The next morning, the charging port LED was red and the vehicle would no longer enter READY mode. I cannot select a gear or drive the car.
The HV battery still shows 100% state of charge.
The problem appeared immediately after that overnight AC charging session. I don't know whether this is related or just a coincidence.
2. 12V battery checks
- Original 12V battery was replaced with a new Varta AGM battery of the same type/specification.
- The issue remained exactly the same after replacement.
- Resting voltage readings have varied between approximately 12.6โ12.9 V.
- During wake-up/start attempts, voltage drops significantly, previously down to 11.7 V and even around 10.8 V.
- With an external 12V charger connected, I measured approximately 14.5 V.
- Without the external charger, the voltage does not rise above approximately 13.5 V during wake-up attempts.
- The latest UNFISKERED report shows 11.61 V โ Critical.
I have therefore not been able to confirm that the DC-DC converter is charging the 12V battery.
3. Checks already performed
- Replaced the 12V battery with a new Varta AGM.
- Checked the IBS connector.
- Checked the 5A IBS fuse (MF06) โ OK.
- Checked the 300A fuse (MF05) โ OK.
- Checked voltage at the relevant fuse points.
- Checked the two additional fuses in the PDU 2M โ OK.
- Performed an HV/LV reset.
- Tried soft resets.
- Tried charging the 12V battery externally.
- Scanned the vehicle using a Vgate vLinker FD+ and the UNFISKERED GO / Wavestripe diagnostic tools.
- PDU diagnostic scan previously showed no stored fault codes, although the latest full vehicle scan now reports active PDU-related faults.
I currently cannot access the relevant live data for DC-DC activation, HV contactor status or PDU operation through my diagnostic setup.
4. Latest UNFISKERED diagnostic report โ November 1, 2026
The latest scan shows:
- 17 active DTCs
- 8 affected systems
- HV battery: 100%
- 12V battery: 11.61 V (critical)
Important active fault codes:
Communication errors:
- U199705 โ Communication with BMS lost
- U199708 โ Communication with DC-DC lost
- U199709 โ Communication with OBC lost
- U176887 โ BMS EV-CAN communication lost
- U176987 โ PDU EV-CAN communication lost
- U12F987 โ Lost communication with BMS_HVBatt_Status_Overall (EPS and EPS2)
- U19F587 โ Missing BMS signal
Component faults reported by the VCU:
- P1010F0 โ HV battery component fault
- P1010F1 โ 12V DC-DC component fault
- P1010F5 โ OBC component fault
- P1010FA โ PDU component fault
- P1012F4 โ Charging connector signal status error
There are also active ADAS errors involving the front center radar and a front ultrasonic sensor.
5. Possible wiring / water ingress issue
I have also been inspecting the wiring in the front right wheel well.
I noticed:
- Several connectors in this area.
- Signs of previous wiring repairs/splices.
- Damaged or modified wiring loom wrapping.
- A ground connection attached to the chassis.
- Possible areas where moisture could enter.
I have not yet confirmed corrosion or water inside the connectors.
I have seen reports from other owners mentioning water ingress around the right front wheel arch connectors, including the washer-fluid level sensor wiring. I am wondering whether a wiring, ground or CAN bus issue in this area could explain the communication faults.
6. What I would like to understand
- Could a failed or interrupted EV-CAN connection explain the simultaneous loss of communication with the BMS, DC-DC, OBC and PDU?
- Could water ingress or damaged wiring in the front right wheel well cause these symptoms?
- Is it possible that the DC-DC converter is not necessarily defective, but simply isn't being activated because the HV system cannot establish communication or enter READY mode?
- What would be the best way to check whether the HV contactors are being commanded to close?
- Are there known failure points, connectors, grounds or fuses that I should inspect next?
- Could the overnight AC charging session have triggered this issue, or is that likely just a coincidence?
I would really appreciate advice from anyone who has experienced similar symptoms or has technical knowledge of the Fisker Ocean electrical architecture.
I am trying to identify the actual root cause rather than randomly replacing expensive components such as the PDU, BMS or DC-DC converter.
Thanks in advance for any help!