r/Renovations • • 7h ago

Advice on insulating basement bath wall

Post image
3 Upvotes

This wall is below grade and I'm a bit lost on how to insulate it with the main water line and ground/bond wires. The gap between the pipe and the wall is too small to get insulation panels behind it, and the wires need to be accessible.

Is it okay to simply leave some small areas uninsulsted, or would that create moisture?

Thanks!


r/Renovations • • 10h ago

HELP Is "regrouting" a thing?

0 Upvotes

When it comes to uneven floor tiles, is "regrouting" a thing? Will it help? Does it mean to add more grout to existing (already dry) grout? Or removing the old grout and putting a fresh new layer?


r/Renovations • • 10h ago

Colorado basement bathroom: faced insulation and poly behind backer board?

1 Upvotes

In Colorado, wild temp swings hot and cold. Basement bathroom.

For the shower wall thats against the exterior concrete in a basement, should we have faced insulation and poly behind the backer board, or should I unface the insulation and use only the poly behind the backer board? I don’t realize I technically created a double vapor barrier.

Red guard and tile has not been placed so I just need to remove the backer board to fix the issue, but what’s the right way?

Same question for the other shower walls that are on interior wall but not against concrete. I wanted to insulate these because a bedroom is on other side of wall. Should we add poly and faced insulation or just one?

*we are redguarding the entire shower floor to ceiling to ensure maximum waterproofing.


r/Renovations • • 11h ago

HELP Billing process

1 Upvotes

My parents are finally updating their kitchen. They recently had a bathroom redone, and although the finished project was decent, it was a tedious process. That guy will not be doing the kitchen.
Anyways- my question is, are these kinds of renovations usually charged by the hour or job?
I feel they got taken advantage of by the last guy.
I’m in Ontario, Canada.


r/Renovations • • 1d ago

Finishing Garage

Post image
3 Upvotes

I’m working in finishing my garage, to heat it.

My current set up is 2” R10 foam board in between my studs. There’s about 2” of space left- should I add something before putting up OSB. If so- what?


r/Renovations • • 1d ago

Need to do renos - cant find permits for old work, so everything needs to be brought up to code ($$$$). HELP

1 Upvotes

Am reaching out to this sub because I need help - need to find old building permits for an addition and basement development, or I have to pay $$$$ to bring it all up to code.

Here's the story:

I applied for a program that provides low-cost loans to help make homes more energy efficient. I had flooding in my basement in the spring and figured since I had to do some renos anyway, might as well make the most of it.

Well. It turns out the water in the basement was the least of my problems.

When we tore out the drywall to determine the extent of the damage - we discovered that the basement had been poorly wired. And in order to get that brought up to code, the framing (which we had partially torn out because of the water damage) needed to be done up to code as well. The framing and electrical need to be done before we can do the insulation.

Thats when this energy-efficient program comes in - in order to be accepted, you have to have your home inspected so they can do an efficiency audit. The inspector mentioned that a few things were not up to current code and that we needed to provide permits for the work that had been done, or the entire basement (and extension) would have to be brought up to code and reinspected.

The basement insulation was flagged as the item that would have the biggest impact on energy efficiency, and am going to do it since it needs to be redone because of the water damage.

The house was built in the 1950s, and as far as we can tell, the addition was put on inthe 70s or 80s. The addition involved pouring a partial new foundation and cutting into the existing. There is plumbing in the basement, and the house had the electrical panel also redone at some point. So clearly there is work that needed to be inspected, meaning permits should be there, right!?

Talking to the City permits office - they have no permits for my house at all. None in the digital records that go back to the 90s. So we've done an archival request and are now going line by line through old records to try and find any permits - but so far can't even find proof that my house exists in the building permits. We can find the development of the rest of the area and surrounding blocks, but nothing for my house.

On my city tax bill, my house is listed as having a separate basement suite. So clearly the city knows something but have no idea what that is or how to find it.

So I am reaching out to people who know how to research, anyone that might have any ideas for tools or ways to approach this. Are there any tools, ai or otherwise, that might be able to help? Where should I be looking for information? The archival records are digital scans of handwritten ledgers. Are there any tools that can help me go through this any faster?

Any help is greatly appreciated.


r/Renovations • • 3d ago

Trying to renovate wood stairs…

Thumbnail
gallery
18 Upvotes

Hello guys,

I feel completely lost renovating the stairs. It’s so difficult to remove the paint, I already spent like 15 hours and still has paint on the wood.

Please see the pictures, do I need to scrap more or I can just sand it and paint it?

Thank you


r/Renovations • • 4d ago

HELP Attaching Framing to Stairs

Thumbnail
gallery
2 Upvotes

Hey guys, not really sure if this is the right sub to ask this or not.

I just built and installed the stairs copying the original set this week. I had to replace the original due to the wall side stringer having massive dry rot due to previous owner not using a vapour barrier alongside the wall.

I know ideally the strapping would go behind the stringer, but that was not how it was originally built, and I didn’t want to change anything, trying to put it back to how it was.

My question is what would be the best way to attach this 2x4 onto the stairs so that I can use it for framing.

Should I trim the stair flush to the stringer and subsequently trim part of the stair flat enough for the 2x4, cut eight tiny pieces to fit over top the stringer, then mount the 2x4 to that(picture 3), or am I better off to just attach 2x4’s cut at a 45’ directly onto the stair/stringer like picture 4?

Sorry for the formatting, on my phone while trying to walk my dogs before work. All help and suggestions greatly appreciated, I’m just trying my best with what I have.


r/Renovations • • 4d ago

Order of works

1 Upvotes

Ripping out kitchen/floor/skirting architrave. But wondering what order to tile floor, fit new architrave/skirting, paint walls and skirting. What order would you do this in? I'm thinking after rip out sand and fill walls, first coat on walls, tile floor, cut and fit architrave&skirting, then final coat on walls then gloss the skirts.


r/Renovations • • 5d ago

Dimpled Foundation Membrane on Interior of Wall

Post image
2 Upvotes

Adding context -- this was done over a decade ago by previous owners. Yes I know it typically goes on exterior of the wall, there is currently no water or leakage, gutters have leaf guard and there's no moisture coming through whatsoever. They claimed to have puddles form pretty frequently and didn't want to spend a small fortune by excavating and doing it on the exterior.

What would happen if I cut it down to about 1 foot off the ground compared to leaving it how it is more than half way up the wall ?

Hi everyone, I want to frame walls in my basement and I'm not sure how to approach this wall. I want to add rigid foam or some other sort of insulation but want to avoid moisture from causing problems once it's finished with drywall. The dimple membrane is about 4 feet up the wall and tucks under the concrete slab. I understand it's roll in diverting water but not sure how to approach it from a framing standpoint.

Should I buy more dimple membrane and "finish" the rest of the wall with it by tucking about 6" behind the existing membrane and going up to the ceiling then taping the seams?

Or

?

I don't know what the other options would be


r/Renovations • • 5d ago

Quick question about bottom of shower

Thumbnail
gallery
5 Upvotes

I put hydroblok as my shower walls as you can see (the gray walls) in hopes of soon to start putting tiles in. However I messed up and left a gap on the bottom as shown on pics (a litttle bigger of a gap than should be).

How do I deal with this??

Thank you so much in advance.


r/Renovations • • 5d ago

Drywalling a funky basement wall

2 Upvotes

I want to put drywall on a basement wall but it has some quirks that I'm not sure how to manage.

This wall runs under the main beam of my house and aligns with the Lally columns holding up the beam. The problem is that the studs sit about 1 inch inside of the face of the beam and the outside edge of the column(s). I know I could just build a new wall in front of the current wall but then I'd lose about 4 1/2 inches of precious interior space.

I THINK I could use some sort of furring strips to build out the face of the current wall but I'm not sure if that is the best solution. I also think I would want to build the face out past the face of the beam so that I could run electrical down inside the wall (IOW, don't make the wall flush with the beam but proud maybe an inch so there is a gap in the drywall at the top for wiring).

Does that make sense?

Will I be able to attach drywall to furring strips?

Also, there is a column just past the right end of the wall. I can't decide if I should extend the wall around this column and back or just turn the wall and the end of the existing studs and wrap the column separately. Any thoughts on that?

Thanks for any insight.


r/Renovations • • 6d ago

Insulating an exterior wall with cement board tile shower on interior

Post image
4 Upvotes

I discovered a fungus surprise behind my shower wall. I think it’s from not being insulated properly, and sealing in moisture. There was kraft r15 in the cavity -> 3/4” clapboard wood sheathing -> 0.2” kingspan xps -> vinyl siding. As you can see, the middle cavity with the least “breathing room” has the most damage from fungus. I was thinking of using mineral wool r15-> osb-> house wrap->siding but am worried it will still seal in too much moisture. What is the best way to tackle this? Also, the pipe is being relocated to the left if that’s relevant.

Edit: framing is also being replaced.


r/Renovations • • 8d ago

HELP Bathroom vanity too big. Shower tiles too combined with floor feels too much. What to do.

Thumbnail
gallery
35 Upvotes

Quick edit to add comment: thank you everyone for sharing your opinion and doing it with such grace and understanding. I was worried about posting this for fear of being criticized but you all have helped me to calm down somewhat. I am really grateful for all that. I spent the whole day out of the house doing things with family to clear my head. When I came back, the questions were still there but didn’t consume me like it did earlier. I know it’s obvious, but I really needed reassurance that this is not the end of the world and from some of the comments, sounds like it’s not tooo big of a deal to swap out the vanity like I thought it would be either. Thank you all and wishing you all the happiest of holidays with family and friends!

I’m spiraling with my anxiety and I feel like I made such a big and expensive mistake. When we chose materials for this small bathroom renovation, I spent hours/days/weeks/months picking materials. We’re almost done with renovations and its looking nothing like how I imagined. I feel so stupid for wasting so much money for the bathroom to come together clashing like this.

Where we are at. Floor is done, vanity is in, shower tiles were partly done then taken down bc we decided to try to make it “straighter” with spacers. (So we ordered more Zellige and spent more money). So right now all that’s really left is to install the shower.

I am spiraling big time. I thought I had chosen neutral enough materials for things to come together, but it all seems to be beautiful on its own but silly together.

For one, the vanity is too big. It fits and the door closes, but its depth extends beyond the level of the door frame.

The floor is beautiful but I am getting cold feet about pairing it with the Zellige. (I’ll post pictures of the zellige that was taken down.)

My husband says not to overthink it and it’s been ordered so just go with it, but I’m terrified once it’s in, then it’ll really be irreversible. At the same time, changing anything out now costs more money and I feel horrible about it.

I don’t know what to do. Will it really look like it’s clashing with all of this or should I just let it go? I also need honest opinions on the vanity. It just feels like it’s way too big and doesn’t belong (it’s actually a white oak color but is showing up more like walnut here). I struggle with anxiety and just want to throw up at this point, but trying to stay functional for the kids.


r/Renovations • • 8d ago

HELP Best way to finish gap between fireplace and shelving

Thumbnail
gallery
3 Upvotes

I am putting shelving on either side of my fireplace (yes TV too high) and am trying to figure out how to fill the gap between the Tyndall stone edge and the shelving side panel. The gap is anywhere from 0-1” wide and is around 3” deep to the back drywall. I’ve thought about getting some matching mortar but I’m not sure if I could just fill the gap with mortar and not have cracking or movement issues. Thoughts or ideas welcome!


r/Renovations • • 8d ago

Vinyl flooring on top of concrete floor!

3 Upvotes

I have a guest room which has some old vinyl floors and has an elliptical sitting in the area. There seems to be some small internal locking wood floors on top of the concrete base and then they put the vinyl on top.

The vinyl floor is becoming puffy or elevated in some places and then breaking because the underneath wood pallets are moving. I had put an anti shock thick rubber floor mat underneath the elliptical after fixing the area last time. Now I am noticing another area is being impacted by the same problem.

- Can I put a new waterproof vinyl flooring directly on top of the concrete base in that room? I am not sure why the previous owner put the small internal locking wood pallets underneath or if there is still a need for it anymore?
- Could there be any problems with moisture, if I put a vinyl directly on top of the concrete base?

Thank you.


r/Renovations • • 8d ago

Hardie backer question

2 Upvotes

I have a room that has a crawl space next to a concrete foundation and the subfloor is level with the concrete and i was wondering if using hardie backer to span the space to lay LFT porcelain tile is a good idea. my thought was to use tapcons to secure the concrete side then normal hardie screws on the subfloor side.


r/Renovations • • 8d ago

Patio door replacement

Post image
4 Upvotes

Hey guys, what is this lip for? Should I caulk over it or is it a drain way? Got it from homedepot, it's a Stanley door and I've not been lucky to find any documentation.

Also, the frame inside is well over the drywall, how far can I sit the door on the exterior side? It'll help get the frame closer to the drywall inside.

Thanks.


r/Renovations • • 10d ago

HELP Desperately seeking guidance

Thumbnail
gallery
17 Upvotes

I recently had to move back in with my mom and little sister. We are all very much down on our luck and can't afford to hire contractors who know what they're doing. So, with the very small knowledge I have, I'm taking on this project. The upstairs half bath reno.

How would you tackle this? Just slap a piece in there, tape, mud, sand, paint, call it a day?

Or would you sincerely worry about the last two pictures? There's a bit of mold on that bottom corner, and the upper corner in the last picture looks atrocious to me. Not to mention a later of drywall ripped off on the right wall that you can see right next to the stud.

But I don't know what I'm doing, and I don't want this to be a bigger problem down the line. Please, give me any and all possible guidance that you can. There's far more work to be done on this house, and it's up to me.


r/Renovations • • 10d ago

How would you fix this transition?

Thumbnail
gallery
6 Upvotes

30 inches . Would a threshold fit ?


r/Renovations • • 11d ago

Project areas to find alternative contractors

3 Upvotes

We are planning a home addition (primary suite) along with some other improvements:

  • Moving a door to a different part of the wall
  • Adding heating to a room
  • adding a landing to the stairs to our patio
  • replacing our swinging door to the patio with a sliding door
  • Replace our front door
  • Moving laundry from the basement to the 2nd floor (to an existing room, not the addition)

Would I save a significant amount of money if I found my own subs to do these accessory jobs? I have a reliable handyman who can connect me with reliable subcontractors so finding folks to do the work wouldn't be an issue.

Obviously I can just go and get some quotes for these things, but most of them are bundled on the estimate so I can't really compare.

Anyone have experience with this?


r/Renovations • • 11d ago

ONGOING PROJECT Lead paint positive test

Post image
14 Upvotes

Tested the paint on the stairs. First came back negative. Scrapped 2 stairs then tested again, bottom layers tested positive.

Stopped and got Klingstrip. Has done a decent job, but tested again and the stripped areas are now testing even more positive than before 😅🤦🏻‍♂️

It’s completely dry and no dust etc. I used a wet cloth etc to clean up after… but am I just wasting time trying to get these back to natural wood? How do I get the lead completely off?

Nightmare is I need to still use the stairs, so have different shoes going up and down, the risk is extremely low (I have been told) as the pint still left is not flaking and there are no loose particles (that I can see)… but don’t want this to go on for ages… do I just paint them and carpet them?


r/Renovations • • 11d ago

HELP Weight capacity bifold door thoughts.

Post image
3 Upvotes

Cut drywall to insert maple 1/2 piece. Screwed maple board into studs with 2-1/2 construction screws. 8 total (4 bottom, 4 top)

then the lag screws are 5/16 with the spacers included in the kit.

it weighs about 120lbs.

Even if I hadn't cut drywall, lag screws would've gone into studs only about half an inch anyway.

Thoughts? AI thinks it's not a good idea, I disagree, and wanna get opinions.


r/Renovations • • 11d ago

Small amount of water coming into basement

Thumbnail
gallery
4 Upvotes

During decently heavy rains I get water in the corner of my basement, right where the wall meets the floor. Something like 3-4 cups of water, only in the one corner. It's a walkout, the corner that leaks has a slab at walkout grade on one side, and is fully underground on the other side. Right at this corner is a 3 tier retaining wall that directly touches the house. I opened the wall inside and don't see any cracks, or wetness on the wall itself, just on the floor. I used a hose on the slab that is on the walkout side, right against the house, and got no water inside. Also used a hose on the bottom tier of the retaining wall and got no water inside. The only spot that really got water to show up inside was the middle tier.

In my mind, the options are:

1:
Add something to catch water at the second tier of the retaining wall and send it into a drywell in the yard. Along the lines of digging out the area, adding a liner and perforated drain tile, backfilling with some rock and then soil and re planting. Attempts to get the water out of the area before going into the house. Cost is mostly labor (couple plants, drain tile, etc).

2:
Sump basin inside the house. My thought was to cut out the spot, add the basin, but wait on adding a pump and plumbing it outside. I can monitor the basin and see if a pump is even needed.

2b:
It was suggested to me that I should cut the floor inside, dig out the corner as if i was adding a very small basin, and instead just backfill with pea stone and monitor the open pit over time. Or even fill it back up to the top with stone and self level it. Ultimately the floor in this room will be finished with carpet.

3:
Open to suggestions.