**Or, “I slaughtered my Loris so you don’t have to!!”**
I’ve had the Loris for about six months now, and it’s been my daypack of choice since I purchased it.
**Things I like:**
Flap top rather than a roll top.
Front body zip for easy access to the main compartment.
Extra cushioning on the shoulder straps.
Dedicated external holster for a sit pad, which can double as a lightweight frame.
**Areas for improvement:**
The shoulder strap mesh pockets taper too aggressively towards the base, making it difficult to accommodate larger phones.
No mesh pocket on the bottom of the pack.
On the heavier side of the ultralight spectrum for a 25L pack.
The relatively narrow body can make packing conventional overnight gear a little challenging.
Overall, though, it’s an exceptionally comfortable, well-built pack that works nicely for overnight trips when paired with low-volume gear.
**So, why slaughter it?**
As mentioned above, the Loris is a little on the heavier side for its capacity. Mine originally weighed in at **474g without the sit pad**, which adds another 65g.
I’ve also been wanting to experiment with modifying some of my existing gear to put together a more specialised ultralight kit, tailored to my local conditions. I’m in subtropical Queensland, where it’s hot for much of the year, most of my camping is at natural campsites, and there’s generally less need for bulky cold-weather equipment.
With that in mind, I figured the Loris would make a good starting point, provided I could shave off a meaningful amount of weight.
**And I did!**
After cutting away various unnecessary panels, pockets, loops, and excess strap lengths, I’ve managed to bring the pack down to **377g — a saving of 97g, or just over 20% of its original weight.**
Here’s what I did.
**Step 1: Removed the top carry handle — 5g saved**
A fairly straightforward modification. I rarely use it, so off it went.
**Step 2: Removed the external sit-pad holsters — 23g saved**
I don’t intend to use the sit pad as a frame, so the mesh holsters were unnecessary. If I ever decide to bring the pad along, I can simply slide it down the inside of the pack instead.
**Step 3: Shortened the four main straps — 14g saved**
I fully loaded the pack, fitted it to my body, and worked out how much excess webbing I could safely remove from the shoulder strap and flap-top adjusters.
I ended up cutting approximately 50% of the length from these straps, then hand-stitched new stoppers into the ends to prevent them from slipping through the buckles.
**Step 4: Removed the internal pouch and zipped mesh pocket — 33g saved**
Turning the pack inside out gave me access to the internal organisation. I carefully cut away the fabric panel and integrated mesh pocket, neither of which I particularly needed.
This turned out to be the single biggest weight saving.
**Step 5: Removed the hydration bladder divider — 9g saved**
Removing the internal organisation in Step 4 left the hydration bladder divider behind.
I’ve never been particularly fond of hydration bladders and rarely use them, so there was little reason to retain this panel.
**Step 6: Removed miscellaneous loops and excess fabric — 13g saved**
Finally, I went over the pack and removed a few additional loops, along with as much of the leftover fabric from the previous modifications as I could reasonably access.
A little here and there adds up!
**The result**
**Original weight: 474g**
**Modified weight: 377g**
**Total saving: 97g (20.5%)**
Importantly, I took care to avoid cutting any of the pack’s structural stitching. All the modifications were confined to features I considered unnecessary for my intended use.
There is, however, one potential downside worth mentioning. With the internal panels removed, there’s now only a single layer of fabric separating my sweaty back from the contents of the pack. Given Queensland’s heat and humidity, this might be something to consider!
In retrospect, I could have retained the hydration bladder divider for an additional layer of moisture protection. That said, I already carry my gear in dry bags, so I’m not particularly concerned.
Ultimately, I’m pretty pleased with the result. I’ve retained the features I really like about the Loris while removing nearly 100g of weight, bringing it much closer to what I’d want from a dedicated ultralight overnight pack.
Whether it proves to be a worthwhile modification in practice remains to be seen, but it’s been an enjoyable experiment.
And, of course, **if you like your Loris exactly as it is, there’s absolutely no need to take a pair of scissors to it!** Plus, thanks to a shipping error, I actually have two, so if it’s ruined, I can break out the spare 😆
I have pictures of mods if anyone is interested.
Cheers, and happy hiking!