r/audiorepair • • 12h ago

Pioneer TX-520 Lamp change

1 Upvotes

Hi, I have a Pioneer TX-520 and am wondering if a drop in led bulb is possible? I want to change the bulb to blue


r/audiorepair • • 15h ago

How to boost the antenna signal on a JBL Tuner 3?

1 Upvotes

How to boost the antenna signal on a JBL Tuner 3?

Hi everyone,

I’m looking for a way to boost the antenna signal on my JBL Tuner 3 to get better reception and clearer sound in my kitchen. The radio is currently placed right next to a west-facing window in western Poland, but the signal is still a bit weak.

Are there any effective DIY/homemade methods to strengthen the built-in antenna? Alternatively, can I buy a clip-on external antenna that would work well with this model?

Any tips or recommendations would be greatly appreciated. Thank you!


r/audiorepair • • 18h ago

Sony ZV-E1: Built-in Speaker Suddenly Stopped Working

1 Upvotes

Hi everyone,

I'm having a strange issue with my Sony ZV-E1 and I'm wondering if anyone has experienced something similar.

The built-in speaker suddenly stopped producing any sound. This happened while I was playing back a video during an indoor shoot.

Here are the details:

- Camera: Sony ZV-E1

- Firmware: Version 2.02

- The built-in speaker is completely silent. No playback audio, no system beeps, not even static or crackling.

- Audio recording works perfectly.

- When I plug headphones into the headphone jack, playback audio works normally.

- As soon as I unplug the headphones, the built-in speaker remains completely silent.

- At the time the issue first appeared, a microphone was connected to the 3.5mm mic input, but no headphones were connected.

- Nothing was connected to the multi-interface shoe. The original Sony shoe cover was in place.

- The camera has never been dropped, exposed to water, or subjected to any impact.

- I've checked the audio settings, the volume and performed a factory reset, but nothing has fixed the issue.

- I've plugged and unplugged the headphones around 10 times to try to reset the headphone jack detection switch, but it made no difference.

The problem appeared suddenly, without any warning.

Could this be a hardware failure involving the internal speaker, its amplifier, or the headphone jack's detection switch?

Has anyone experienced this issue with a Sony ZV-E1? I'd really appreciate any advice or suggestions before sending the camera in for repair.

Thanks in advance!


r/audiorepair • • 1d ago

Rear speaker issue JBL 1300xMK2

1 Upvotes

So picked up a brand new 1300xMk2 back in March and it’s been working great…until a few weeks ago. Noticed that the rear speakers (which I have plugged in nonstop in their spots behind the couch) started showing a solid red light, which the user guide states is that they are charging. Odd, because they never did that until recently but the app showed they were charging up.

Last night, I noticed that the lights were still on, but there was no sound coming from either, and the app didn’t recognize they were connected. Thinking they unpaired by accident, I plugged them into the soundbar, and they both came alive playing music I sent to the soundbar to test. As soon as I detached them, they blinked white twice and then stopped playing music.

Confirmed they only play sound when connected to the bar itself. Reached out to support and the agent was super helpful and had me connect them to the soundbar overnight while in standby to eliminate the issue if the charger brick/cable being the issue. Tried it this morning after about 8 hours of the speakers being connected to the bar, and same issue. Contacted support again to give them the update and they are going to send me two speakers.

While I appreciate the help from support for sending me them (initially was going to send a new bar too but they wanted the current setup back first, which would be a pain, but might take them up on it if this doesn’t work) something seems off about both satellite speakers failing at the same time. Almost makes me think it’s a software issue, but idk how to factory reset it all.

Has anyone else noticed the same issue happen with theirs?

TL;DR: satellite speakers both stopped working at the same time, but support thinks I’m the fix is just swapping the speakers out.


r/audiorepair • • 1d ago

Headphone hinge locking failed

Post image
2 Upvotes

I've had this pair of oneodio studio pro 10 headphones for 3yrs now, and on both ears, whatever's in place to limit the hinges that connect the ears to the headband into a limited range of motion have failed, meaning that wearing them pushes the ears outwards to the point where they're not resting against my ears (as shown here w/ the left ear). I've managed to disassemble the right side as far as everything but the hinge, but can't find a way to get into the hinge itself.

What do I need to do to get into the hinge so I can see what's broken inside?


r/audiorepair • • 2d ago

When gear is unsalvageable, which components do you pull out to potentially repurpose?

6 Upvotes

Well over a year in this hobby, and I'm still learning the ins and outs of electronics repair - and I imagine my learning days will continue until I die or retire!

Today's question brought to you by a '90s Pioneer CD changer that lost its lens and can't reasonably be fixed. I'm preparing to ship it to Gear Valhalla (ewaste collection bin), but before I do, I'm stripping it for parts that might be usable later.

Screws are a big favorite of mine to save, as I mainly work with Pioneers of that era and their screws are largely interchangeable. Fumbled and dropped one onto the floor? Heard it roll away? To the screw drawer!

I'll always grab the badge off of the faceplate as well, of course.

I haven't started saving plastic gears, but I'm tempted to, after seeing posts on here about how they frequently get stripped. It seems like a long shot that they'd be interchangeable between most pieces of equipment, but they're so small that I definitely see the appeal of stuffing a drawer full of 'em.

How about you, what do you always keep? What else should I be saving?


r/audiorepair • • 2d ago

Dynaco ST70 (VTA ST-120) issues distortion on one channel

Thumbnail gallery
9 Upvotes

Hi All,

Hoping that someone maybe able to assist in troubleshooting my St70, actually the modernized VTA St-120 from Bob Latino. KT120

I have totally degraded sound in one channel, low volume.

I have replaced the all tubes and rectifier, Quad cap has proper voltages, My rectifier pins 4 and 6 have 170VAC.. (I thought those should be much higher?) All other rectifier VDC pins measure correctly.

On my driver board..

I have 515VDC on the B+ and all four power tubes have bias.

Now, here is an issue;

R20 and R22 on the right channel side are absolutely cooking off and are melting their own solder when the unit is powered on. They are burning up bad. I don't have enough troubleshooting knowledge to trace that issue..

I am hoping that someone out there might be able to offer suggestions...

Thx!


r/audiorepair • • 2d ago

Yamaha CA-810 Relay Cycling Help?

Post image
5 Upvotes

My beloved CA-810. Purchased recapped and serviced September last of 2026. I just moved, it was working perfectly when packed. Unpacked it, normal 3-5 second pause, but almost as soon as the relay engages it releases. That cycles continues indefinitely 'click-click', pause, 'click-click'. Looking for some help on how to troubleshoot past what I've done already.

-

Meters dip with each click cycle, but meter illumination stays constant.
No speakers/sources have been connected since removing from packaging after move.
Same behavior on multiple known good outlets and with the plug flipped both ways.

I've measured +/-40V stable on +/- power supplies, +/-25V stable on regulated supplies, both 1A fuses (removed) measure okay for continuity, as does removed mains fuse.

Left and right outputs both measure negative for DC at Lo-E and Ro-E respectively (pre-relay). The relay coil (Matsushita AP3422) measures 639ohms. The relay coil receives short voltage pulses that happen along with the 'click-click', but measures 0V between the click cycles.

Research pushed me toward protection circuit. Measurements taken:

TR606: emitter 40V stable; base ~40V dipping during relay cycle; collector 0V with short pulses during clicks; base-emitter ~0.6V during relay cycle.
TR605: emitter ~3V dropping to near 0V during clicks; collector 40V stable with drops during clicks; base-emitter ~0.5V jumping to ~1V during clicks.
TR604: base-emitter slowly rises to 0.6-0.7V then drops to almost 0V during clicks; collector ~3V falling to near 0 during clicks.

D603/C603: gradually charges from ~1V to ~6.5V then collapses during clicks to ~1V again.

Checked some AC loss detection stuff:

C604: negative to 'E' (channel ground) solid continuity, same with C604 to R613 low side; AC measurements were ~1.1V dropping to ~0.9V with clicks; 100Hz frequency measured between click cycles and lost during click-click briefly.

R613 high side is stable at 27.5V and low side (C604 positive) sits ~3.5V dropping to ~1.5V with relay clicks.

Other related components:

R611 to TR604 base measured good continuity.

R612, R614, and R615 all measured within tolerance.

D807 and D809 measured ~0.587V forward and ~2.95V reverse with occasional OL (on PCB, not separated).

-

I'm NOT a tech. I'm just a decent tinkerer with a volt meter who's handy with a soldering iron. With that said, it seems to me that amp outputs and supply rails are okay, relay winding measures fine. That makes me think (through my limited research and knowledge) protection/AC loss detection, but I can't find what is initiating the reset. I haven't removed or desoldered anything yet.

Does anyone have any idea? Has anyone had a similar experience? I feel like I'm kinda at the edge of what I can cover without better equipment but I want to make sure I'm not missing anything major. Current plan is to reflow solder in the areas of concern to rule out loose/intermittent connections, and if still no juice to start replacing protection circuit/AC loss detection parts.

-

TL;DR - CA-810 relay won't stay engaged after unboxing from a move. 3-5 second pause, engages, then immediately releases. I've done a lot of troubleshooting and want some advice based on what I've already done, even if that's just some affirmation that my planned next steps are appropriate. Not a tech, just a guy with a volt meter and decent soldering equipment.


r/audiorepair • • 2d ago

Audio equipment repair advice

Post image
1 Upvotes

Hoping to get some advice from someone who might know a thing or two about audio equipment.

I got my hands on this JVC compact component system from the early 2000’s but it doesn't seem to be fully functional. I know I could take it to an audio repair shop, but I’m not entirely sure what the issue is or whether it’s worth spending $200+ to have it repaired.

For context: It didn’t come with the original remote, so I purchased a universal one. It powers on normally, but the motorized top cover doesn’t respond when I press the open/close button. As a result, I can’t access the CD currently stuck inside, let alone get it to play. There is also no motor noise whatsoever when I press the buttons.

Curious to hear people’s thoughts:)


r/audiorepair • • 2d ago

Nikko 9095 Hiss

1 Upvotes

I've got a vintage receiver Nikko 9095 that has a soft hissing white noise coming from the speakers on any channel and gets louder the higher up the volume gets. I had some work done on it that I'll list below.

Replaced transistor differential pairs in Poweramp.

Replaced trimmer potentiometers in Poweramp and adjusted DC offset and bias to factory specs.

Amplifier output transistors have new thermal grease and pads.

Replaced all electrolytic capacitors in poweramp, preamp phono preamp, and power supply.

Signal path capacitors replaced with film type capacitors.

All transistors in preamp and phono preamp replaced.

Bench tested for 0.1% THD at 71 Watts per channel into 8 ohms at 1 KHZ.

Unfortunately the low hiss still persists. Any thought of what might be causing it?


r/audiorepair • • 3d ago

Left Channel Audio Is Staticky

1 Upvotes

My new Sears Audio By Fisher AM/FM Stereo Receiver has static on the left speaker inputs. Even when playing audio, you can only hear very muffled/staticky song rhythm once you turn the amp volume up to at or past noon. I’ve noticed that simply dusting the speaker clamps with canned air made the audio clear up a little possibly (could just be placebo), but still unrecognizable. How can I fix this? Hopefully something that contact cleaner will fix? I have little to no experience working on old stereo amps like this.


r/audiorepair • • 3d ago

Pin on PCB came loose

Thumbnail gallery
4 Upvotes

Me again with the Denon Receiver.

Thanks for the help so far.

When trying to reconnect two PCBs via two fixed connectors (foto 2 and 3), one of the pins got pushed out on the other side, which probably happened, because the pins got crooked when I disconnected them.

Anyway, the solder joint is still holding the pin but the PCB surface came loose (foto 1).

Is this going to cause problems down the road? If so, how do I fix this?

Thanks!


r/audiorepair • • 3d ago

Yamaha stereo motherboard

Thumbnail gallery
1 Upvotes

This broke off and I wanna know if this is why my stereo won’t work. If it is then where to get a new board and for how much pls


r/audiorepair • • 3d ago

Onkyo MD105 FX 'Read Error' on all discs

1 Upvotes

Hi folks. My Onkyo MD105FX which has worked pretty seamlessly for 10 years has just started behaving oddly. On inserting an MD yesterday the Onkyo repeatedly pulled the MD in and ejected it for a while. I couldn't stop it repeating the in-and-out manually, so I switched it off at the mains and extracted the disc carefully. 
When I switched it back on it behaved normally and played the disc but it seemed as if the mechanism for loading was a little shaky.
Today I inserted various discs, each one loaded normally but the 'Read Error' message came up every time, without the sound of the machine attempting to read the disc. My hunch is that there is a small mechanical glitch in the door mechanism or something similar.
I'm no techy, but I did once previously manage to open the machine and remove an MD that wouldn't eject (which turned out to be because it had two labels on the MD).
I'm wondering if there is a way I can fix the Read problem - any help much appreciated.


r/audiorepair • • 3d ago

Old JVC CD/Cassette player door jammed, clicking noises

1 Upvotes

Hi, I bought this used micro component system (JVC UX-P6R) last month, and while the CD player is clearly in need of repairs, the cassette player has been working wonderfully. However, it's now been a couple days since I last used it, and as I just got a new cassette that I ordered three months ago, I wanted to use it ASAP.

However, when I put the cassette in and closed the door, I just heard a bunch of loud clicking noises, as if it was trying to rewind but getting stuck somehow. Now I can't even open the mechanical door, no matter what I do.

What could have happened? What can I do once I eventually open it up?


r/audiorepair • • 4d ago

Gift ideas for one of you

2 Upvotes

Hi! My husband is really into repairing receivers and turntables. I’m not sure exactly what he has but I know he recently got a scope of some sort. He especially loves sansui. I was hoping to get him some gifts and stocking stuffers. Any ideas?


r/audiorepair • • 4d ago

Paradigm Studio 100 .v4 dust cap suggestion

Post image
1 Upvotes

Facebook Marketplace find. Picked them up for 200 CAD but 1 speaker has pushed caps. Any link or suggestions for perfect match dust caps?

Thanks.


r/audiorepair • • 4d ago

Ghost switching Pioneer.

1 Upvotes

My old Pioneer vsx D912 is starting to switch to CD when I power it off. I'm only using the main power button, the only button on my remote that doesn't work. I'm just guessing but it's something in that cluster of switches.


r/audiorepair • • 4d ago

Revox B780 Help needed

Thumbnail gallery
2 Upvotes

I have a Revox B780 amplifier whose batteries have leaked.

I've taken it apart and cleaned everything. The amp turns on, but the buttons on the front panel don't work.

What could be causing this? Or what could I do?

I don't have the financial capacity to get it fixed professionally but I can solder and have a multimeter. I don't have the electronica knowhow (yet) but am hoping that the internet can help me further.


r/audiorepair • • 4d ago

How to fix play button

Thumbnail gallery
1 Upvotes

Does anyone have any clue how to fix the play button on a Sanyo GXT-838? I attempted to test the dubbing on a cassette tape because I just got this unit yesterday from the thrift store.

It was a beautiful find as everything seemingly worked perfectly. And after some testing (discluding the turntable as im waiting on a new stylus) everything was working great.

But then I went to go and press that dang play button on tape A as I press the record and play on tape B and the button just pops down and started flopping around. Ill post a photo of what it looks like just hanging there and picture of it positioned to the highest it can go. Seemed to be completely disconnected from its resting spot wherever it was.

If theres more info needed please let me know and I csn provide as much as I know! Thank you guys!


r/audiorepair • • 4d ago

Denon AVR with water damage

Thumbnail gallery
2 Upvotes

Hello everybody!

Unfortunately I have a little bit of water in my AV Receiver.

I know my way around electronics a little bit, but I can’t take apart this last piece of PCB shown on the pictures.

These little black connectors seem to hold the vertical PCB in place. Any tips on how to take this apart?

Thanks in advance for your help!


r/audiorepair • • 4d ago

Help with my Pioneer speakers

1 Upvotes

I have a pair of speakers I use for my TV music through my phone they both worked when I got them and for the last few months one of them just suddenly stopped playing sound through it. I change the wires over and that speaker works and the other one stops then 🤷 I got new wires today plugged them in and the same things still happening model number for the speaker are S-DJ80X thanks for any help


r/audiorepair • • 5d ago

Marantz HD-AMP blinking red light

1 Upvotes

I know this topic has been covered before, but my situation seems a bit odd.

My Marantz HD-AMP has a fast blinking red light suggesting an electrical fault. So far it seems typical.

But - it happens only when the system is off (standby mode). And if I unplug the power and plug it back in, it returns to normal operations. And this only happens once in a while - maybe once every week or so.

Any help or hints would be much appreciated.

Edit: I should mention that I am using a surge protector power strip


r/audiorepair • • 5d ago

Fix mv88

1 Upvotes

My iPhone dropped with the mv88 adapter in it.

The insertion pin is slightly, if at all bent.

It does not work.

Can I fix it myself, or bring it somewhere where I won’t have to pay the full price for Shure tech?