r/breadboard • • 3h ago

Question whats wrong in this can anybody help ? clap switch circuit using buttons as mic is not in tinkercad

Post image
1 Upvotes

r/breadboard • • 23h ago

Next step - Add insulated tinned coper wire straps made to measure.

Post image
34 Upvotes

Making custom straps and soldering into position before discrete components and modules are added.


r/breadboard • • 1d ago

I need to power 3x Mg90s , Mg996R servos which power supply can i choose ( 5v 10 A or 5v 20A)

Thumbnail reddit.com
1 Upvotes

r/breadboard • • 1d ago

Question How do I make a reset switch for my laser tripwire

Post image
5 Upvotes

I'm new to using a bread board. I'm wondering how to make a reset switch.

Example

Laser is pointed toward the LDR - > laser gets blocked - > alarm goes off - > laser is unblocked but the alarm is still going off - > press the button to reset the alarm.

My current progress? I don't know what I'm doing. I'm also figuring out how to use a potentiometer.


r/breadboard • • 1d ago

Built a computer a while back

Post image
43 Upvotes

r/breadboard • • 2d ago

Breadboard Mini 4 Channel Motor driver

Thumbnail gallery
1 Upvotes

Love using SMD components 😋


r/breadboard • • 2d ago

Project Day Two of Breadboarding! Am I any good?

Post image
7 Upvotes

I'm a grade 12 student trying to learn breadboarding as a hobby and for prototyping in the future. I made this with Tinkercad, as that is what I am familiar with. I challenged myself to make things as compact as possible.

This project currently has 3000+ edits 💀.


r/breadboard • • 3d ago

Yall are circuit nerds, right?

Thumbnail reddit.com
0 Upvotes

r/breadboard • • 4d ago

I made a circuit puzzle game and a set of free interactive guides for beginners. Would love your feedback

5 Upvotes

Hey everyone,

I’ve been working on a game called Volt Trial. It’s a puzzle game built on a real circuit simulator. You place batteries, LEDs, resistors, capacitors, transistors and a few chips, wire them pin to pin, hit Run and see what happens.

The part I care about most is when it doesn’t work. If an LED stays dark, the game tells you why: open loop, reversed polarity, a short, too much current or a joint you forgot to solder. You can tap any pin to see voltage and current, or watch a resistor heat up without burning your fingers. There’s also a story mode that walks through the history of electricity, from the Leyden jar to the microcontroller.

While building it I kept writing explanations for myself, and they turned into a free learning section: https://phabletapps.ro/learn

There are guides on Ohm’s law, Kirchhoff, breadboards, reading schematics, transistors, the 555 and more. Several have a small tool built in, like an LED resistor calculator (you can remove the resistor to see why it’s there), a resistor color code tool, a voltage divider and series vs parallel.

You can play the demo version of the game in your browser here: https://volttrial.phabletapps.ro/
It’s free to start with no ads, and Android is in closed testing and the production release is under review.

Don't expect to be a professional tool like SPICE, I wanted it to be like a translator for the abstract physics in a more human natural language :). It's definitely not a guide to mains wiring.

What I’d love to hear:

  • Did anything confuse you, or is anything wrong in a way that would teach a bad habit?
  • What did you struggle with when you started that I should cover next?

I'll be replying here once I have the Android version published in Production.

Happy soldering, and let me know your thoughts. Thanks!


r/breadboard • • 4d ago

Breadboard Two-Input AND Gate using Diodes

Thumbnail gallery
27 Upvotes

r/breadboard • • 4d ago

Next Step towards a PCB maybe?

Post image
10 Upvotes

So, I am preparing my second copy of my project stripboard having previously using a breadboard arrangement to develop it.

For those that have never used tinned copper stripboard before I thought you might like to see the track cutting process before I start adding interconnecting bare tinned copper wire straps that will be insulated with black rubber sleeving to complete the track from one module pin to another.

The blue handled tool is the track cutter and I have been known to do elaborate track cuts with a scalpel blade to solder surface mount components indirectly to the copper side of the board. Just imagine how much board space you can save adding SMT devices on the copper side.


r/breadboard • • 5d ago

Creando un ADC y un DAC

Post image
21 Upvotes

He estado creando un circuito que actúe como un adc y un dac, usando amplificadores operacionales y compuertas lógicas, los amplificadores se conectan a 6.5 volts y las compuertas a 5 volts, esa es la lógica que estamos usando para que funcione, hasta el punto de las compuertas funciona (lo qué es el ADC) pero la última parte lo que es el DAC ya no


r/breadboard • • 6d ago

Chip Hippo gets social: a gallery of breadboard circuits you can open or share

Thumbnail
gallery
8 Upvotes

Chip Hippo is a free, open-source simulator for 74LS TTL and CD4000 CMOS circuits on virtual breadboards. 1.5.6 adds a gallery*: browse circuits, open one* straight in your browser with nothing to install, or pull it into the desktop app.

You can share your own, too. Still no accounts: build a circuit, choose to share to the gallery, and once it's reviewed and approved it's there for anyone to open and download. Every design has its own link to send to a friend.

Also in 1.5.6: 
- Labels on the toolbar buttons
- Redrawn Run, Wire and Bus icons, and a lot of smaller UI tweaks

See for yourself:
- Gallery: https://chiphippo.com/gallery/
- Try it in the browser: https://chiphippo.com/desktop/
- Downloads (macOS, Windows, Linux): https://chiphippo.com
- Source: https://github.com/jfigge/chiphippo


r/breadboard • • 6d ago

I've been developing a Bluetooth multimeter with integrated circuit design tools. Looking for some feedback!

33 Upvotes

I'm an electrical engineering student, and for my entrepreneurship class I've been developing a project called PocketOhm.

As part of my final assignment, I'm conducting some market research to determine whether this is something people would actually find valuable enough to purchase.

PocketOhm is a compact Bluetooth multimeter paired with a mobile app, designed for electronics students, hobbyists, and makers.

The idea came from my experiences as an engineering student and circuits lab TA, where I've seen how much time can be spent identifying components, recording measurements, and switching between calculators and other tools.

Here's what I've developed so far:

  • Bluetooth DMM: Measures DC voltage, resistance, and continuity.
  • Saved measurements: Record measurements and reuse them directly in circuit calculations.
  • Interactive calculators: Voltage dividers, Ohm's law, RC filters, and other circuit design tools.
  • Component identifier: An experimental expansion module that can recognize certain components and measure their characteristics. Still working out some bugs with this one!

The attached video demonstrates a simple example of the workflow: measuring a battery and resistor, saving those measurements, calculating the values needed for a voltage divider, and then building and testing the actual circuit.

This is a real working prototype, although there's still plenty of development and testing ahead.

Here's where I'd really appreciate your feedback:

I'm considering a retail price of approximately $89 for the Bluetooth DMM and app, with no subscription. The component identifier would be a separate accessory.

  1. Would you seriously consider purchasing something like this at that price? Why or why not?
  2. Does the integration between measurements and circuit design tools offer enough value over your existing equipment?
  3. Which features would be most valuable to you, and what would make this worth purchasing?
  4. If $89 isn't appealing, what price would you consider reasonable?

I'm not selling anything or taking orders. I'm just trying to determine whether there's enough interest to justify continuing development.

I'd appreciate honest feedback, including criticism. I'm particularly interested in hearing why someone wouldn't purchase it.


r/breadboard • • 6d ago

Question Am I forced to buy in bulk with capacitors, fuses, resistors, etc?

11 Upvotes

I dont really do this as a main hobby but I do love playing around with circuits and stuff. I have a project, I want to #d print and build my own PC racing wheel and pedals, but basically all the little parts I need are sold in bulk and have priced the total build to $130 before printing and stuff. Is there a way I can just buy the 3 capacitors, 3 fuses, 4 resistors, and the few specific parts I need? I cant find a store online anywhere...


r/breadboard • • 6d ago

RadioShack Reverb Controller 32-1107 + DIY breadboard Synth 555 timer

Thumbnail
m.youtube.com
1 Upvotes

r/breadboard • • 7d ago

OG breadboard ready for some tube amp experimentation!

Post image
8 Upvotes

r/breadboard • • 7d ago

From Breadboard to Stripboard

Thumbnail
gallery
39 Upvotes

Time to move over to a compact version for final project integration.

Two photos, breadboard and tinned copper stripboard.

Stripboard is effectively a single sided PCB where by cutting away copper at certain locations and adding straps on the top side it can be turned into an effective double sided circuit board. No printing circuit design and immediate results but not so good if you intend to make multiple copies of your circuit.

Stripboard fitted with screw terminal connectors to wire up battery packs, neopixel LED strip and PIR motion sensor. From top down : Pololu high side switch, DS3231 RTC and ESP32-C3-Zero super mini.


r/breadboard • • 8d ago

Question Voy a hacer mi primer pcb con el método del ácido y el marcador. Algunos consejos?

1 Upvotes

r/breadboard • • 8d ago

I made a free open-source app that turns a project ideas into 3D breadboard step by step for beginners

47 Upvotes

I bought a Pico 2W. I was no electronic experience so tried to solve that problem. I decided to build a beginners friendly application to learn electronics. So here is the project I am building and maintaining. It is a desktop app ( supports macOS, Windows, Linux) for people starting out with the Pico 2 W.

You type an idea like "show the room's temperature and humidity on the OLED screen", and it gives you:

- a plan and a checked circuit (pins, resistors, breadboard layout),

- numbered build steps on a 3D breadboard, each with a short "why",

- MicroPython code, checked before you see it, built into one .uf2 file you drag onto the Pico.

The AI only handles the language part. Pin choices, layout and the safety rules (shorts, missing resistors, wrong voltages…) are ordinary tested code, so it can't hand you a circuit that fails the check.

New in v0.3.0:

- Change a finished project ("add a button that switches the display between icons and text"). Parts stay put and you only get the new steps.

- DHT11, slide switch and passive buzzer, all tried on a real Pico 2 W.

- Pick a local model through Ollama, or use an OpenAI key if you have one.

Honest limits: small local models still get harder projects wrong more often (5/10 vs 10/10 for GPT-6 Luna in my test with the new parts) and it supports a limited set of parts so far (LEDs, buttons, potentiometer, SH1106 OLED, plus the three new ones). I'm planning to add more components and more micro controllers in the future.

GitHub: https://github.com/Prestical/BreadPilot


r/breadboard • • 9d ago

Mi full adder de 2 bits todo bonito como lo quiero

21 Upvotes

r/breadboard • • 10d ago

Opensource 3D breadboard sim in the browser

8 Upvotes

r/breadboard • • 11d ago

Astable Op Amp LM358 Demo Circuit

Thumbnail
youtube.com
7 Upvotes

r/breadboard • • 11d ago

Project Modular ESP32 system for rapid prototyping

Thumbnail gallery
5 Upvotes

Hey, working on building a modular ESP32-based system, open-sourceing as much as possible, including AI-CAD, digital twins, such that anyone no matter hardware experience can build their own ESP32-IoT devices.