r/electronic_circuits • • 1d ago

On topic High side N-MOS driver with no GND connection (POC)

4 Upvotes

The circuit works as follows:

  1. When the NMOS is loaded, body diode voltage drop Vsd is used to power a boost converter circuit, generating a voltage pulse to charge its output capacitor
  2. The boost converter powers a bistable multivibrator, that drives the mosfet's gate, periodically pulling the gate low
  3. When the gate is pulled low, Vsd increases and the cycle repeats

I have a feeling, the boost converter could be somehow simplified, because it's designed to be self oscillating, but in this circuit it's only ever used to generate a single pulse, everytime gate is turned off. Maybe using a feedback winding on the inductor?

I welcome any improvements.

PS. It's basically POC at this point in time, eventually I want to mold it into an ideal diode circuit.

Also here's a link:

https://www.falstad.com/s.py?s=2ry1eK


r/electronic_circuits • • 1d ago

On topic I made an amplifier with a tda2050 hooked up a Bluetooth module and connected it to my Milwaukee battery so I can jam at work.

Thumbnail
gallery
15 Upvotes

The speaker is junk but it got pretty loud


r/electronic_circuits • • 1d ago

On topic I made a 9v 2/4/6/8 step sequencer with an atari punk console and an lm380 amplifier to let it bang a little louder

7 Upvotes

Pictures in comments


r/electronic_circuits • • 1d ago

On topic How do I power this string of parallel LEDs ?

Post image
2 Upvotes

I am repairing/renovating a small Christmas tree lighting string built into a larger Christmas mountain display. There is a string of 8 tiny LED's wired in parallel, terminating in two wires. I applied a test 3v and lit LEDs numbers 1,3,5,7 Then applied the 3v but reversed the polarity to make LED's 2,4,6,8 light up. So it needs some sort of switching IC or circuit?

The original PCB is toast, so can anyone help provide an answer on how to power the circuit? TKS.


r/electronic_circuits • • 2d ago

On topic I need advice on where to place the ground using a oscilloscope.

Thumbnail
gallery
0 Upvotes

I’m working on repairing a MiniMe P10. I have an oscilloscope to troubleshoot what’s broken in the power supply board. But I’m having trouble finding where to put the ground.


r/electronic_circuits • • 4d ago

On topic LM5116MHX based step down converter pre-regulator

1 Upvotes

Hello, this is a little project I've been working on lately. It's a 65V input, 5-50V 25A output step down converter that I want to use for a regulated PSU - this will be the pre regulation stage, then I will add a linear (transistor) regulator after it for fine voltage regulation. I'd ideally like even more voltage, but currently I'm using some hybrid capacitors and they aren't available in higher than 80V.

Which gets me to the first question: what's the best way to approach the output caps? My current config is 12x 47uF with 36mOhms ESR each (GYA1K470MCWADNGS), which have more than enough ripple current rating and come out to around 111mV output voltage ripple. I've tried calculating with 4x UCS2E221MHD, but those have significantly higher ESR (presumably, since Nichicon doesn't specify ESR at the 200kHz this converter is running at) - if I input 100mOhms per cap into the equation, the voltage ripple comes out to around 0.875V, which is insane. I guess the main problem is the 10A ripple current from the converter. Now, if I use ceramic caps, then I'd also have to use a huge bank, especially because of the DC bias/capacitance curve, not even mentioning it would cost at least 15-20 times the price of the hybrids.

The use of the hybrid cap bank gets me to the layout: it's far from ideal, but I think it's as good as I can make it with these components. The inductor is rated as having 45.9A saturation current, so it should be enough. The feedback is connected to the 6 pin header, so that I can connect an external regualtion circuit to it. The zener diode on the output (it's a 36V zener) should prevent the output voltage from being unpredictable if anything happens to the external regulation circuit.

Schematic and layout here: [https://drive.proton.me/urls/KV5ASAPQ6G#sYs0FYXTC8zI](https://drive.proton.me/urls/KV5ASAPQ6G#sYs0FYXTC8zI) (hope everyone can access this, I don't have an Imgur account and I apparently can't put more than one picture here in the post).

Hopefully I can get away with a 4 layer board while all layers being 1oz copper - most of the power planes are huge and the main connections are on two or more layers with plenty of vias in between.

I have never done such a high current/high power design, which is the main reason why I'm asking for a review here.

(btw, vias are free, right, right??)


r/electronic_circuits • • 5d ago

On topic Can anyone identify what are SW1 and SW2 are for on this time logging board please?

Thumbnail
gallery
13 Upvotes

As the title… this is from a carpet cleaning machine, its only purpose is to display and retain the hours the machine is in use.

The battery needs replacing which is why I’ve removed it.

I’m wondering what the SW1 and 2 are for on the battery side of the board. More importantly I’m hoping they can advance the time artificially, as when the battery is removed (and when it’s gone flat previously) it loses the time stored. If they don’t, does anyone know how I could do this without leaving the board mains powered for x-hours.

SW3 on the front serves only to display the currently logged time briefly when the machine is switched off.


r/electronic_circuits • • 7d ago

On topic I made a Ni-Cd battery charging circuit of 12V that has 10 cells each with 1.2V

Post image
20 Upvotes

Hi, Everyone. I have made a Ni-Cd battery charging circuit that has 10 cell in series, each with 1.2V. My charging adapter supplies 24V, 3A. From that I have regulated it to 12V 3A and from that to 12V 1A. I want a review about the design, mistakes and optimization advice. Thank you.


r/electronic_circuits • • 7d ago

On topic Ippon UPS charging circuit

Post image
6 Upvotes

Hello everyone! The image shows a portion of an Ippon UPS circuit—specifically, the charging circuit. The power MOSFET is not shown, but that is not important. My question is: in your opinion, is the charging circuit continuously regulated by the central processor, or is the charging process divided into several distinct modes? Alternatively, does it simply toggle between "charging" and "not charging" states?


r/electronic_circuits • • 9d ago

On topic EasyTrace5000 PCB CAM update

Post image
7 Upvotes

Hi, some months ago I posted about a PCB CAM tool I'd been working on. A lot of development in the mean time has been mostly around non-pcb stuff so it didn't make sense to post about it but by now there's enough new stuff that's worth an extra mention.

There's a laser pipeline for anyone with access to Fiber/UV lasers, there's a soldermask stencil operation that was made with cnc, laser and vinyl cutters in mind.

Tool-changing is in there but consider it experimental until proven otherwise.

Latest update I added i18n translation support. There are a few languages included (very LLM generated, although I'm going to review Portuguese next and already have 1-2 friends willing to help with 2 other languages and I'll be pestering a few more friends later).

It also added the ability to drop custom files of a few kinds, including language packs (which means you can make your own if you have trouble with the existing ones) or post-processors (not full post-processors logic yet but more like machine/controller setups, say I set a wrong flag or you don't want to manually change 4th axis alignment all the time).

Still 100% free, client-side and open-source.

Live version moved slightly to https://cam.eltryus.design/easytrace5000/ and source code is at https://github.com/RicardoJCMarques/EasyCAM5000 .

Cheeryo


r/electronic_circuits • • 11d ago

On topic As a beginner, Trying to understand Transistor and Current, Anyone explain this circuit?

Post image
12 Upvotes

R1, R2 = 1000ohms

If i run this circuit, what will happen to the LED?

Will it turn ON or OFF?

And my theory is if i run the circuit it charges the Base and opens the path to flow the current at zero resistance (Red Line) in Transistor making it as a short circuit.

Since there's Zero resistance the current prefers goes thru the transistor (Red Line) but not through the LED (Yellow Line).

So the LED remains Turned Off.

But the reality is the LED is turned ON, why? Ai isn't giving me the right answers, appreciate it if you make this dumb guy understand.


r/electronic_circuits • • 10d ago

On topic I made a tool for designing perfboards, How can I make it better?

Post image
0 Upvotes

I dont know how many of you use perfboards for your projects, but I always use them instead of ordering custom PCBs, and if you had to deal with perfboard projects, you know it is always better to plan ahead before starting to solder things. So for that reason, I vibe coded a tool spesifically for making perfboards. The reason I made a seperate app for this instead of using existing ones is, the other apps were not really perfboard focused, and I wanted an algorithm to use jumpers and solder paths in an optimal way, so the app can give me the best routes for jumpers and solder paths instead of me having to draw them line by line. I think it worked out great, but I need your advice to make it better.

its completely free and open source, and I tried my best to make it easy to use. My only profit from this is knowing it might help someone some day, just like it helped me with my projects. So, if you ever struggle with Perfboards, or just want to take a look, you can find this project on Github PerfboardMaker. I will post the link in the comments.


r/electronic_circuits • • 11d ago

On topic Halloween motion sensors.

Thumbnail
gallery
9 Upvotes

Seeking the input of your combined wisdom. I'm looking to build motion sensor switches for Halloween projects, and I have cobbled together YouTube ideas and my own less than rudimentary electronics knowledge. Pics and proposed wiring diagram attached. This seems my best option for really short duration "on" cycles of 5-10 seconds, and quick reset.

I think my big question/concern is whether a 5vDC input into that HC-SR501 infrared sensor will in fact output a 5vDC signal to the relay board ? Or does it output something else entirely that I would need some kind of processor to interpret ?

Any other input into my plan would be appreciated. Line voltage "extension cord" through the project box and relay, with a remote cabled photo sensor in another small box. Thanks again !


r/electronic_circuits • • 11d ago

On topic Looking for Axtek AX1621B LCD Driver Datasheet (or confirmation it matches HT1621B)

1 Upvotes

Hi everyone,

I am trying to find the official PDF datasheet for the Axtek AX1621B 32x4 LCD driver.
I know it is likely a clone of the Holtek HT1621B, but I want to be sure. Does anyone have the official Axtek PDF, or can you confirm if the pinout and commands are a 100% exact match to the Holtek version?

Thanks!


r/electronic_circuits • • 11d ago

On topic Question about a component in librepcb design software

0 Upvotes

Where would i find the part lp2951 it a voltage regular but cant find it in the library of parts


r/electronic_circuits • • 11d ago

On topic DRV8300D high-side switching

Post image
3 Upvotes

Hello guys, I am experimenting with very basic motor control and with it's electronics. For this purpose I have used the DRV8300D, and I encountered a problem, when I try to switch the high side NMOS and it does nothing.

I try to control the DRV8300D with my Arduino, the lower MOSFETs are reacting, only the high-side doesn't. I know that I have to charge the pump circuit trough the lower MOSFETs and for this reason I also can't use 100% duty cycle for the upper one. It still doesn't work if I switch the lower on for much longer period than the upper one.

I made a quick schematic so you can see what I did there, the Vcc is 12V and the DRV is powered by 10V from an LDO


r/electronic_circuits • • 12d ago

On topic [Review Request] 36 V regen brake + precharge board for a 3-DOF robot arm (rev 3) - organized schematic for precharger

Thumbnail
gallery
4 Upvotes

This board sits between a 36 V bench supply (25 A limit) and three XT30 outputs feeding Unitree IM6014 motors on a 3-DOF arm. It precharges the bus, keeps regen out of the supply, and dumps excess regen into a brake resistor.

What's on it:

- Input: XT60 from the supply, 20 A / 58 V MINI blade fuse (Littelfuse 0997020.WXN in a Keystone 3568 holder), SMBJ43A TVS

- Precharge: a TPS48111-Q1 drives Q5 (IRFR120N) through two 60 Ω PTCs in parallel (Vishay PTCEL13R600LBE). Once the bus reaches 60% of the supply (comparator U3B), it switches in the main FET Q4 (CSD19536KTT).

- Reverse blocking: LM5050-1 ideal diode with a CSD19536KTT, so regen doesn't go back into the supply

- Brake: TL431 reference and comparator, UCC27517 gate driver, TO-220 brake FET, MUR1520 freewheel diode, and an off-board Arcol HS100 4.7 Ω 100 W resistor. Turns on at 40.2–42.2 V (set by RV1) and off about 2 V lower, to stay under the moteus r4's 44 V limit.

- Outputs: three XT30PW-F (15 A each), the same connector the motors use

- Other: 4000 µF / 100 V bulk capacitors, SMCJ43A on the bus, 12 V from an R-78HB12, bus-voltage ADC output and a brake flag

- Board: 2 layers, 2 oz copper, 96.5 × 128 mm

Where I'd like opinions:

  1. Brake window is 40.2–42.2 V on a 36 V supply. That leaves 2–4 V of headroom below the moteus r4's 44 V limit, and it turns off at 38.2 V or above, so it can't latch on at 36 V. Is that margin enough, given resistor and TL431 tolerance and how fast the bus can rise during hard regen?
  2. Main FET switches in at 60% bus. I did this on purpose: it lets the motors draw about 0.5 A at 36 V during precharge without stalling the PTCs. Q4's gate is slew-limited to about 750 V/s, which is roughly 3 A into 4000 µF. The alternative is about 90% (R28 = 9.1k). Which would you pick?
  3. TPS48111 current sensing is unused. CS+ and CS− are tied together, ISCP goes to VS, and IMON/IWRN are grounded. Once Q4 is on, only the 20 A fuse protects against a shorted output. Is it worth adding a shunt? I mean I could just check with PSU when arm is running.
  4. TVS choice. The SMCJ43A on the bus clamps at up to 69.4 V, which protects the R-78HB12 (72 V max) but not the moteus controllers (44 V). Their protection is really the brake. Is a TVS still worth having here, or would you do something different?
  5. The 20 A fuse limits the whole board. I haven't measured the arm's real current yet. Cause I know that we have a 27 PSU and using

Things I'm already cleaning up: refilling zones before exporting Gerbers, syncing schematic fields to the PCB, updating footprints from the library, and adding LCSC part numbers. The XT60 input already uses Amass's drawing hole sizes.

Schematic and layout images are below. Any feedback is welcome, especially on the brake threshold and the precharge switch-over point.


r/electronic_circuits • • 12d ago

[Review Request] 36 V regen brake + precharge board for a 3-DOF robot arm (rev 3)

Thumbnail
gallery
0 Upvotes

This board sits between a 36 V bench supply (25 A limit) and three XT30 outputs feeding Unitree IM6014 motors on a 3-DOF arm. It precharges the bus, keeps regen out of the supply, and dumps excess regen into a brake resistor.

**What's on it:**

- **Input:** XT60 from the supply, 20 A / 58 V MINI blade fuse (Littelfuse 0997020.WXN in a Keystone 3568 holder), SMBJ43A TVS

- **Precharge:** a TPS48111-Q1 drives Q5 (IRFR120N) through two 60 Ω PTCs in parallel (Vishay PTCEL13R600LBE). Once the bus reaches 60% of the supply (comparator U3B), it switches in the main FET Q4 (CSD19536KTT).

- **Reverse blocking:** LM5050-1 ideal diode with a CSD19536KTT, so regen doesn't go back into the supply

- **Brake:** TL431 reference and comparator, UCC27517 gate driver, TO-220 brake FET, MUR1520 freewheel diode, and an off-board Arcol HS100 4.7 Ω 100 W resistor. Turns on at 40.2–42.2 V (set by RV1) and off about 2 V lower, to stay under the moteus r4's 44 V limit.

- **Outputs:** three XT30PW-F (15 A each), the same connector the motors use

- **Other:** 4000 µF / 100 V bulk capacitors, SMCJ43A on the bus, 12 V from an R-78HB12, bus-voltage ADC output and a brake flag

- **Board:** 2 layers, 2 oz copper, 96.5 × 128 mm

**Where I'd like opinions:**

  1. **Brake window is 40.2–42.2 V on a 36 V supply.** That leaves 2–4 V of headroom below the moteus r4's 44 V limit, and it turns off at 38.2 V or above, so it can't latch on at 36 V. Is that margin enough, given resistor and TL431 tolerance and how fast the bus can rise during hard regen?
  2. **Main FET switches in at 60% bus.** I did this on purpose: it lets the motors draw about 0.5 A at 36 V during precharge without stalling the PTCs. Q4's gate is slew-limited to about 750 V/s, which is roughly 3 A into 4000 µF. The alternative is about 90% (R28 = 9.1k). Which would you pick?
  3. **TPS48111 current sensing is unused.** CS+ and CS− are tied together, ISCP goes to VS, and IMON/IWRN are grounded. Once Q4 is on, only the 20 A fuse protects against a shorted output. Is it worth adding a shunt?
  4. **TVS choice.** The SMCJ43A on the bus clamps at up to 69.4 V, which protects the R-78HB12 (72 V max) but not the moteus controllers (44 V). Their protection is really the brake. Is a TVS still worth having here, or would you do something different?
  5. **The 20 A fuse limits the whole board.** I haven't measured the arm's real current yet. prob ably planning to measure from PSU anyway.

Things I'm already cleaning up: refilling zones before exporting Gerbers, syncing schematic fields to the PCB, updating footprints from the library, and adding LCSC part numbers. The XT60 input already uses Amass's drawing hole sizes.

Schematic and layout images are below. Any feedback is welcome, especially on the brake threshold and the precharge switch-over point.


r/electronic_circuits • • 12d ago

Looking for MikroTik LHG 5 (RBLHG-5nD) Schematic / Boardview

Post image
1 Upvotes

Hi everyone,

I'm repairing a MikroTik LHG 5 (RBLHG-5nD) and looking for its motherboard schematic, boardview, or circuit documentation.

The board contains the following components:

Qualcomm Atheros AR9344-DC3A

Winbond 25Q128JVSM SPI Flash

Ethernet transformer: TS21CW

I'm doing component-level troubleshooting. When powered through the PoE input (24V, current limit set to 500mA), both the AR9344 and Winbond flash IC become excessively hot.

I'm looking for documentation to trace the power supply rails and investigate the PoE and Ethernet circuitry.

Any schematic, boardview, PCB layout, service manual, or repair notes would be greatly appreciated.

This is a personal electronics repair project, not a commercial repair request.

Thanks in advance!


r/electronic_circuits • • 13d ago

Problem with 74hct4051n

Thumbnail
gallery
2 Upvotes

Hi everyone!

I'm working on a circuit-bending project involving a Yamaha PSS-47, and I'm running into some strange behaviour with a 74HCT4051N multiplexer.

My setup:

\* Yamaha PSS-47 with its ROM data lines exposed for circuit bending.

\* LTC1799 oscillator replacing the original ROM clock.

\* ESP32 controlling a 74HCT4051N.

\* The 4051 is used to sequence different ROM data-line connections.

I'm connecting the Y0–Y7 pins of the 4051 to different ROM data lines, with the common Z pin connected to my bend point. The ESP32 controls the address pins (A, B and C).

The strange behaviour:

The circuit bends actually work better when I disconnect VCC (pin 16) from the 74HCT4051N.

When I connect 5V to VCC, the bends stop working properly. With VCC disconnected, I get much more interesting and functional bends.

I've also been looking at the signals with an oscilloscope. When zooming in on the signal, I can clearly see the high-frequency LTC1799 clock. The screenshot is from the controlling pin of the ESP32 S3.

My questions:

  1. Why would the 4051 appear to work better when VCC is disconnected?
  2. Is the 74HCT4051N suitable for switching ROM data lines in this application?
  3. Could the external clock be causing problems with the multiplexer or its signal integrity?
  4. Is there a better way to sequence ROM data-line bends using an ESP32?

I'm particularly interested in understanding why disconnecting VCC changes the behaviour so dramatically.

Any suggestions, explanations or alternative circuit designs would be greatly appreciated!

Thanks!


r/electronic_circuits • • 13d ago

On topic Can these speakers be disconnected without destroying the circuit

Post image
25 Upvotes

I'm restoring a mid-60's electric piano (Hohner Pianet) that has internal speakers and a line out. I'd like to be able to have the option to turn off the internal speakers. Can I simply add an on/off switch in series with the speakers. I don't want to destroy some of the old, hard-to-find germanium transistors in there.

Disclaimer: I'm a hobbyist and can solder and some debugging but I suck at any circuit analysis.


r/electronic_circuits • • 13d ago

On topic Electromagnetism-Im trying to clip the top of the waveform with a transistor but calculations arent working

Thumbnail
gallery
13 Upvotes

I generated a sine wave using a Colpitts oscillator, which I powered with 12V, and it correctly produced a 958kHz waveform with approximately 6.86Vpp. Now I'm trying to clip the top of the waveform with a transistor, but my calculations aren't working correctly, or I don't know what's wrong. I tried placing a variable resistor at the collector to see how the waveform changed, and the result is what you see in the video.


r/electronic_circuits • • 15d ago

Making PCB soon, would like second opinions on circuit!

Post image
27 Upvotes

Currently working on an OpenCV mecanum car thing, I am fairly confident in the layout so far but would appreciate the double check from someone else! Lmk if yall find anything wrong with what I'v got going on, ty! (I2C and XSHUT lines will be pulled high using internal pullups on PI 5).

Lipo is 2s (7.8v) and the PCA9685 is simply used to have more PWM chanels on the PI 5.


r/electronic_circuits • • 15d ago

On topic How about this component layout and soldering job?

Post image
2 Upvotes

Do you have any comments and/or advice regarding this board layout?

This is my first ever self-designed and self-built project in electronics. My background is actually civil engineering lol

The board was designed to charge and discharge an actuator made of stacked piezoelectric disks up to 200 V. I split it into a logic and a power circuit, each at one side of the board to avoid arcing and/or short circuits.

The logic circuit gets 12 V from a switching power source, lowers it to 5 V using an LM7805 and goes to an ESP32 after a few decoupling capacitors.

The connection between the logic and power circuits is made via two TLP627 optocouplers, which keep the low and high voltage circuits isolated.

The source voltage is boosted to 200 V by the yellow module at the top-right corner of the board, which I raises about 1.5 cm with nylon bolts to allow some air below the board, provide electrical insulation and enough room to run the power wires below it.

A bootstrap circuit allows to raise the gate-to-source voltage of the first N-MOSFET via the proper switching of the optos, charging the piezos. The second N-MOSFET connects the bootstrap circuit to ground to discharge them.

The idea is to have the ESP32 charge and discharge the piezos based on a linear quadratic regulator (LQR) controller, so that the actuator can control the vibration of the host structure.

I tried to use component leads as much as possible for connections and use the least solder possible. Is this how perfboard layouts usually look?

Up to now, everything seems to be fine. The logic circuit is working, I managed to get a simple PWM signal out if the ESP32. Now I'll start hot-testing the full circuit.