r/handtools • u/politiphi • 23h ago
Latest dovetails with mitered faces
First time getting something close to the 3D look I see y'all post all the time.
r/handtools • u/politiphi • 23h ago
First time getting something close to the 3D look I see y'all post all the time.
r/handtools • u/Inevitable_Frame782 • 18h ago
Hey, I made a kerf extender to help with half blind dovetails. It’s just an old card scraper and a scrap of oak with some thumb screws to hold it in place. Not pretty but works surprisingly well. I’m not sold on if it’s really necessary but it does the job.
r/handtools • u/X1010 • 17h ago
I designed this monitor stand so that my wife’s laptop could live in the middle shelf and my keyboard could slide into the bottom opening. I started with rough cut maple and oak. My workshop is hand tools only so I sized with handsaws, planed everything flat and square with no. 6 & 4. The maple knot was a challenge and took a lot of patience to get low enough through the various bits of tear out. Of course the deepest tear out was in and around the knot! Filled the voids with black CA glue. Laminated 2 maple boards together for the shelf, cut dados in the oak legs for the shelf with handsaw and chisel method (I don’t have a router plane yet so the chiseling took a long time). Chamfered the top and inside edges of the legs with a block plane. Sanded everything to 220 being careful to not break my chamfer lines. Used a spoke to do the fading chamfer on the shelf. Ebonized the oak with iron/vinegar mix I made. The method I used brushed strong black tea I boiled followed by the mix. It took 4 coats of each to get dark enough that I was satisfied. I have my thoughts about how this turned out but I’m curious what others think. Next I doweled the top, finished everything with Glancy’s oil then 9 thin coats of shellac (including the oak, which after testing looked much richer with oil over the ebony). Turned out better than I expected. I don’t love the slight lines I got in my shellac finish but at a certain point I figured I’d better stop messing with it and I can always go back and remove/reapply if I get better at finishing in the future. I did buff the finished coat with 1000 grit 3m pad which helped imo. This was my first real project where I tried for furniture level finish and it was very satisfying!
r/handtools • u/Andi_FJ • 5h ago
When I drove to the timber merchant about 3½ years ago and bought kiln-dried beech timber, I didn’t realise at the time that I would have to learn a great deal over the years in order to achieve a decent result with this wood. The plan was to use only hand tools and mortise-and-tenon joints. It took me the first year to get from rough-sawn timber (33 mm thick) to planed 25 mm boards. In the process, I learnt both how to sharpen planer blades and how to deal with the straight edge and twisted grain. I fitted a Japanese stone to the Tormek, and eventually got into the habit of sharpening the blades every 6–8 hours. Up to this point, apart from the groove in the laminated timber, I’d done everything with hand tools.
In the second year, it was time for most of the mortising work. When cross-cutting the boards, I used the plunge saw for the first time. I quickly realised that whilst beech is very strong, the wood can also split. So I put the large wooden mallet aside and applied countless blows with the wooden mallet to the chisels to create the joints in the body.
Along the way, I also fitted a sanding guide from Veritas, as the narrower chisels kept tilting sideways in the Tormek holder. For the finishing touches, I still had some hard oil and sanding fleece to hand; I modelled the drawer mounting on that used in other pieces of wooden furniture. To complete the project, I joined the drawer components using 8mm wooden dowels (drilled with the (instead of a manual one).
I’m very pleased with the result, even if some of the details really do scream ‘rustic furniture’. From a commercial point of view, the chest would be priceless, but for me it was a wonderful learning experience, and I reckon I could even sell the electric planer now ;-)
Next on the agenda is a shoe rack made from acacia wood – that’ll be fun, as the wood can be sawn, planed and worked in no time at all :-)
r/handtools • u/Inevitable_Frame782 • 18h ago
Hi guys, I finally got myself a 605 (thank you to the awesome Josh Clark), and am wondering what if anything I should do regarding restoration. I’ve done full “back to new” restorations on other planes but am not convinced this needs it. Apparently it was from a trade school, hence the paint and hang hole. Then there’s the chip on the front of the body - I considered using JB SteelStik to even that out. I could also just file any sharp corners to prevent any bloody knuckles and call it a day. I think the tote is rosewood so kinda would like to make that pop a bit more. Please let me know what you think and thanks!
r/handtools • u/EntireBlackberry7831 • 16h ago
I’m visiting Japan would like to bring a gift or two back from a shop that sells handmade wood working tools for my brother who is an experienced woodworker. He makes very fine pieces (ornate tea and keepsake boxes, cabinets, box shelves, candle holders, etc) and obviously has a pretty solid collection of tools that he’s bought, made, or restored over the years. I’d like to keep it a surprise but can also ask him for guidance if necessary.
Is there anything that is a go-to when it comes to Japanese tools? I’m sure I can’t go wrong with something like a nice marking knife, a pair of chisels, a saw, or a small hand plane or two. Any advice on sizes/types would be appreciated in that case.
Feel free to recommend anything I haven’t thought of as well. Thanks!
r/handtools • u/Responsible-Wear8407 • 21h ago
Went to check if the rake maker II was back in stock yet and I see this. I’ve read online that the guy had been considerably less active in recent years , but I was under the impression he was still keeping things running in some small capacity. Does anyone know anything about this??
It’s really sad for me to see this website go. His website was an invaluable resource for me when learning how to sharpen hand saws and I hope these resources can be preserved in some way for future novices.
r/handtools • u/DustinNielsen • 3h ago
I'm next of kin for my reclusive uncle who had to be moved to assisted living this year. I was cleaning out his garage and found these. The Stanley no6 looks like it was tried literally one time.
There is a Stanley No 6
A Keen Kutter KK6
stanley no 110 with some missing pieces unfortunately
Craftsman (otherwise unmarked) with missing front handle
Stanley block plane that looks complete
r/handtools • u/ganjaccount • 17h ago
I posted a few weeks ago seeking advice on how to salvage a deeply pitted blade. I ended up realizing that I have a too-thick blade in an old #6 and never got around to opening the mouth. I intend to use that blade in the wooden jointer, rather than grinding a half inch or so off the existing, deeply pitted blade. The old forged blade had a chip breaker.
My understanding is that the primary requirement for fitting a new blade (Assuming it's about the same width) is to create an appropriate wedge to marry the blade and plane body. Is this correct?
Thanks!