r/macrogrowery • • 15h ago

Good evening from icecream cake

Post image
8 Upvotes

r/macrogrowery • • 20h ago

Science Super Pumped

Post image
5 Upvotes

Hopefully this is cool, but i wanted to show some pics of the cultivation ERP I built. I built it based off my own experience managing a 25k sq ft indoor. It's been a lot but getting it to the point of being able to share with the professional community is huge for me!! Appreciate it, hope you like it


r/macrogrowery • • 22h ago

AI Bots/Agents

0 Upvotes

Hey everyone, I'm looking for anyone that has introduced AI agents like Grok Bot/Dots to manage METRC or (third party track and trace) compliance software in their day to day. any feedback would be greatly appreciated.


r/macrogrowery • • 2d ago

24 hours light, for the last 7 days of flower. Who else has experience with this? 270 rooms. 180,000 plants.4500 strains have had this treatment. It’s now a permanent event in the grow.

Post image
189 Upvotes

r/macrogrowery • • 2d ago

A little wiggle goes a long way

25 Upvotes

r/macrogrowery • • 2d ago

DDRP a canopy management system I’ve developed that increases yield, and completely removes the need to gut(lollipop) or defoliate. 6lbs per light. Day 8 vs day 47.

Thumbnail gallery
59 Upvotes

DDRP stands for dynamic dominance reset protocol.

Why are we growing sticks and leaves? Push sink strength away from leaves and stems into flowers as hard as possible and and get rid of the majority of labor on your rooms.


r/macrogrowery • • 2d ago

Follow up thread to my ddrp topic. A timeline for those interested. Day 1,2,5,7,43

Thumbnail gallery
35 Upvotes

r/macrogrowery • • 2d ago

Help! Anden RMA hell

4 Upvotes

Anyone still using Anden dehus? my facility is stocked with them, but their company seems to have went to shit and Im phasing them all out for quest.

back in April, had a 710 go down. fairly new unit, contacted anden, they approved a replacement, said it was taken about 10 weeks as the compressors were on back order. pretty long time to wait for a dehu. literally a whole crop cycle.

whatever things happen, I sucked it up and bought a new 710.

nov 4th of this year i open a warranty claim for a 320, again, newer unit. started using it in 2025. I contacted anden on the 5th, they sent me a message on nov 5th saying its still under warranty and they will replace the unit, just send them shipping address, name, phone, etc. I did all that, and didnt get a reply from them until the 14th, after I followed up with them 5 times.

finally got a response and it was "good morning, I have submitted a warranty replacement

At this time, replacement units are running at a minimum lead time of four weeks. Unfortunately, there is not a way for me to expedite the process without the required inventory. If there were, I would certainly do so.

I apologize for the inconvenience and will do everything I can to help move the replacement process along as quickly as possible."

same day, I asked if they would just approve of a buyback for the unit. I doubt that they would, but it didnt hurt to ask.

no response, followed up on the 16th, again on the 17th, again this morning, no response.

they dont pick up the phone.

anyone else been in this situation with them? did you do anything to get a resolution? im definitley going to phase all my andens out for quest units. hell, might just grab a shipment from china because last time I heard, quest just bought them so im a bit worried im going to be facing the same experience with quest. main reason I go with these larger more established companies is that they stand behind their products and warranty wasnt a pain in the ass. but honestly considering i have to pay twice for some units because they cant get their shit together makes me want to judt pay for cheaper ones abroad and eat the costs when one goes down.


r/macrogrowery • • 2d ago

Chitosan

1 Upvotes

Who’s running it and at what doses. The product line I was using had just doubled and gotten way harder to get. So I’m changing brands and looking for what others are mixing and using.


r/macrogrowery • • 2d ago

I would assume I had exposed roots, but these never touched soil. Anyone seen this before?

Thumbnail gallery
6 Upvotes

The seed ban and resulting subreddit drama nuked the sub I would usually post this in. Feel free to delete as I'm definitely not macro.


r/macrogrowery • • 2d ago

The myth that “too much light” is a lie. Your problem is plant shape, and leaf surface temperature.

Post image
0 Upvotes

r/macrogrowery • • 3d ago

Help! Suggestion on how to set up new room.

Post image
9 Upvotes

Looking to see what are everythoughts on how I should set up these rooms. They are 15x30 with slope on ceiling going from 12’-16 . Open to all suggestion from lights to hvac system with medium . We still need to run electric . It’s basically bare bones as you can see. Was thinking 3 rolling tables 24’. Long.


r/macrogrowery • • 4d ago

PPFD/Nutrient PPM Ratios

4 Upvotes

When moving your plants through the various stages of growth, do you tie the EC/ppm of your nutrient solution to the canopy PPFD? Conventional wisdom says that plants that receive more light can and do use more nutrition, but this will be the first run where we turn our lamps up above 60%. I'd be interested to see even anecdotal data on your adjustments, including your preferred maximum and minimum ppms in relation to growth phase. I've noticed a wide range of standard feed concentrations, from as low as 900ppm throughout flower to as high as 2100. We currently feed between 1100 and 1500 based on the week, which I am content with--but there's always room for improvement. Many thanks.


r/macrogrowery • • 5d ago

More purple sea

96 Upvotes

Coming down tomorrow


r/macrogrowery • • 5d ago

Science "Behind the scenes: Fertilizer mixing routine for our grape vines. Part 1! 🌱"

13 Upvotes

r/macrogrowery • • 6d ago

Corrosion on expansion tanks.

Post image
1 Upvotes

We are having to replace some of these about once a year and I feel like they’re rusting earlier than previous years. Is it recommended to purge each rooms lines at the end of each day free of nutrient solution to mitigate or rather prolong the rusting from popping up?


r/macrogrowery • • 8d ago

STAY AWAY FROM SCYNCE LED'S

36 Upvotes

We have throughout our company history spend over 200k on scynce led's. . . and then they started breaking. Started out just a few, and the company RMA'd them, then they changed their RMA policy to you pay shipping, which basically costs the same as a light for us.

EVERY SINGLE LED WE BOUGHT FROM THEM HAS FAILED. This includes new models, old models, new ballasts etc.

The company was bought by a new guy a couple years ago, and the problems have continued.

We tried multiple times to at least get replacement lights, but they refused.

They sent us a power logger because they thought it was an issue with dirty power. The meter they sent only had 2 legs to measure a 3 phase, so idiotic to even try this method, but we did it anyway. We also (at our own expense) rented a 3 leg power logger and measured against theirs. Both meters proved our power was within normal specs of their lights (and every other light of course).

We have been in business for over 12 years, and have had multiple LED brands, some better than others, but the Scynce have been BY FAR the worst.

The lights are shit, the owner is shit, the company is shit, the RMA procedure is shit.

Just do yourself a favor and buy something else.


r/macrogrowery • • 9d ago

Brain Freeze Day 21

Post image
75 Upvotes

Another 3 part series on a different strain. This will be first, post 21 day defoliation.

This room's results will be a bit different. Most of the lights are 660w uptop. 480w of UCL down below. I have 4 different lights testing in here.

1 x 1000w HongYi Helios spectrum tuning

1 x 645w 3.2PPE Flexstar Redline

3 x 800w HongYi

16 x 660w random chinese brand

84 x 120w UCLs.

I got the extra UCLs abit late so pruned off more of the bottoms than usual so that may have given extra boost to the remaining buds left. I noticed they doubled in size compared to last run with 42 UCLs.

I would also like to reiterate this is my personal R&D facility. I have multiple experiments going on. Including liquid cooling LEDs which I will save for another post.


r/macrogrowery • • 10d ago

Late Flower Fruit Gushers - 2 weeks from chop

Thumbnail gallery
73 Upvotes

r/macrogrowery • • 9d ago

Colorado grow space buildout contractor/consultant

3 Upvotes

Looking for an experienced, proven, contractor/consultant to help with a small grow space buildout in a residential setting.

Must be experienced/proven, good references, ability to hold an intelligent conversation, etc.


r/macrogrowery • • 10d ago

AAON Units

Thumbnail gallery
19 Upvotes

I’m sitting on a bunch of AAON units ranging from 18-25 tons that have never been installed. I was curious as to if anyone might be looking to add on some RTU’s/upgrade their HVAC in here. Feel free to DM me on specs/questions.


r/macrogrowery • • 10d ago

Caked Up Candy

Thumbnail gallery
68 Upvotes

These turned out real nice, strain is Caked Up Candy. My second time growing these, they turned out really nice.


r/macrogrowery • • 11d ago

Anyone know where to get rid of some dehus?

2 Upvotes

Shut down my grow, got some dehumidifiers left over and brand new in the box. honestly just want them out of my way. I had a buyer lined up today to schedule a pickup but they've since.lost interest i assume. Quest 506 is available and possibly 2 335a and an anden 320 if the buyer doesnt respond. all are brand new in the box and newer units, I believe 2026.

Anyone know where to sell em? honestly just kinda want them out of my way. located in canada if that matters.


r/macrogrowery • • 12d ago

UCL Maxxing pt4 (Final Harvest)

165 Upvotes

Video taken 2 weeks ago. We have since dried and trimmed. 131lbs total on 21 top lights. 82 UCL. This will be the final part as promised. No more posting on reddit for me.


r/macrogrowery • • 13d ago

MacroGrow 🫐 Blueberry Cane - (Blueberry Runtz x Strawberry Cane) Bred by Holy Smokes

Thumbnail gallery
13 Upvotes