r/mazdaspeed3 • • Nov 02 '19

Mazdaspeed 3 discord server

30 Upvotes

Hey guys I made a discord for this sub, feel free to join! https://discord.gg/5NQDzGH I’m also looking for admins to DM me if your interested.


r/mazdaspeed3 • • Sep 07 '22

r/Mazdaspeed3 FAQ

41 Upvotes

In other words, fucking annoying questions. Just kidding. (only a little)

In an effort to clean up the sub a bit, we're going to pin this FAQ thread and keep it updated with any of the most requested/asked questions on the subreddit. If there’s a question you think should be included, tag one of the mods in a comment and we will add it.

Introduction

Q: Where is the link to the Discord Channel?

A: Right here.

Q: What should I look for when buying a Speed3?

A: Check the Wiki.

Q: Where can I find a copy of the shop manual?

A: Check the Wiki.

Tuning

Q: How do I load a tune on the car?

A: Using either a Cobb APv3 or computer software like Versatune.

Q: What tuner should I use?

A: There are a number of good tuners still active in the community. Purple Drank Tuning, Freektune, Stratified Auto are just a few examples.

Q: Should I use the ______ version OTS tune?

A: No. Unless it’s to drive the car to the shop where it will be dyno-tuned, do not use the OTS tunes. They make the engine run poorly, resulting in incomplete combustion (or worse, lean conditions) which then gunks up components like O2 sensors, injectors, and valves which lead to worse problems later on.

Mods

Q: What should my first mod be?

A: HPFP internals, then tuning solution. (Cobb APv3, Versatune)

Q: My goal is to go faster around the track, what mods should I do for more power?

A: No power mods. Proper tires and suspension will do more for your track time and drivability than any power mod will. It is guaranteed if you are new to track driving, the car is faster than you are right now. Get some seat time, find what you want to change, get new tires & suspension, then go from there. Dragsters, show-offs, stance-bois need not apply this logic.

Q: My budget is <$500, what coilovers should I buy?

A: None. If you’re not buying quality suspension, don’t buy suspension. You will sooner than later blow out one of the dampers and require a rebuild, or replacement. Save your upfront money, buy quality suspension later.

Q: Should I buy an Eonon headunit for my Bose/non-Bose stereo?

A: Do you like sound quality? If yes, don’t buy Eonon. Do you like good, bug-free software? If yes, don’t buy Eonon. Do you like overpaying for junk that looks ‘clean’ in the car? If yes, then buy Eonon.

Q: What’s the best way to upgrade my stereo in the car on the cheap?

A: Option 1 – get an amplifier that take hi-level inputs and add that amp to the system to power your aftermarket speakers, taking the high-level outputs from either the HU or the Bose amp. Works for Bose and non-Bose systems. Option 2 – Tear out the OEM system and start again. Works for Bose and non-Bose systems.

Maintenance/Troubleshooting

Q: What oil should I run?

A: This is realistically a nuanced question. Ultimately it depends on your use case. Factory rating is a quality 5W30, Mazda put out a TSB to band-aid the smokey turbos by using 5W40. Good options from Pennzoil, Amsoil, Castrol, etc are available for most applications. Most people it seems have strayed from the Shell Rotella.

Q: Are my compression numbers okay?

A: Check the Wiki.

Q: I want to drive the car like it’s supposed to be, but don’t want a ticket. Where do I go?

A: Look on facebook for local car clubs, or Motorsportreg.com for drop-in track days or Auto-cross events.

Q: My car does this thing, and this behaviour, read this wall of text. What’s wrong?

A: No one knows. Post logs using Datazap and any codes that your ECU is spitting out. If you want good information, provide good information.

Q: HELP?

A: No. Posts with this as the title, or other related and equally non-descript variants, will be removed as spam.

Meta

Q: Can I post links to other sites with information, like MSO, without getting banned?

A: Yes. In the event that you’re linking relevant webpages, there is no risk of getting reprimanded for doing so. However, if all of your comments are “Use google.” Or “Go check this site instead, this places sucks.” You will be treated according to the spam rules of the sub. This community serves as a connect-all point for those searching for information on the platform; Reddit is bigger than any Speed forum has ever been, and is more likely to pop up in a Google search. Relevant comments that link other sources of information from quality sites are Bueno; spamming is not.

Q: Why isn’t buying/selling allowed on the sub?

A: This is more of a regional issue that the mod team would like to deal with at this point. There are countless local Facebook groups, classifieds, or Forum pages about buying/selling Speed parts or accessories. The Mod team does not want to dabble in attempts to prevent scams caused by non-payments, or non-shipments of products. We do not want that responsibility at this point in time. If the community deems it a requirement at some point, we will implement a system that attempts to curb this as other buy/sell communities have; though even that change will take lots of time, effort, and consideration.

Q: Why is the mod team so cool?

A: I really don’t know, perhaps divine intervention? We all just really like Doritos, and satiate our inner masochist streak by owning these cars.

Q: How do I become a Mod?

A: If you feel so inclined, feel free to reach out! We are still people, we have feelings and ultimately a desire to help the community grow. What we will need to see is a demonstrated history of helping the community with the best of intentions and overall a positive interaction with the sub. Newer accounts (<1yr) are unlikely to be considered, though that’s not a hard-and-fast rule, just a general rule of thumb.

Acronyms

APv3: AccessPort version 3; the most recent version from

Cobb. Version 2 is still around, but obsolete.

HPFP: High Pressure Fuel Pump

HU: Head Unit

OTS: Off The Shelf; used in the context of tunes

TSB: Technical Service Bulletin


r/mazdaspeed3 • • 2h ago

MODIFICATIONS Steering wheel cover because the wheel was disintegrating

Post image
16 Upvotes

Pretty happy with how this turned out! My wheel was coming apart and leaving chunks on my hand every time I drove. I went with a custom cover for $100. Alcantara on the top and bottom with leather on the sides. Now I just need a cover for the emblem!


r/mazdaspeed3 • • 10h ago

HELP Need help with my Mazdaspeed 3 build

4 Upvotes

Hey I got a 1st gen speed3, it’s tuned, cst4, front mount mishimoto, hpfp, pretty much all the bolt ons. i wanted to build it cs it blew up (or something I stalled it putting it back in gear after going over a speed bump and it never ran again. it was at 236 coolant temp and no compression) I bought Manley pistons for the car nd rods and I tried rebuilding it but I ordered the wrong one (.5mm too big) so I put the stock pistons and rods back in (new piston rings and bearings) ended up with no compression (again) , too big so now I want to swap the motor with a 2.5, sleeve it with darton sleeves, and drop in the pistons (with rods ofc) & use the speed 3 crank and head, just wanted to ask for some tips or advice on the build and maybe if how my engine died sounds similar someone can give me insight cs I still don’t know why it blew up (timing chain was tight did find metal shavings in the oil but could not trace where they came from.


r/mazdaspeed3 • • 17h ago

HELP Downpipe bolts access dilemma (replacing the turbo)

Thumbnail gallery
10 Upvotes

Long time no see! Working on replacing the turbo, I have some aftermarket downpipe on there (previous owner). The top 3 bolts came out with minimal drama. This one (actually both) underneath has no clearance for a socket, a flare nut wrench, or a standard box end of a wrench.

Crow foot type is all I can think of but with the high torque, I could just see that nut rounding off.

Any other ideas?? Thanks


r/mazdaspeed3 • • 23h ago

HELP Noise somewhere along the belt?

5 Upvotes

r/mazdaspeed3 • • 1d ago

PIC After all this time lurking, it’s finally official!

Thumbnail gallery
72 Upvotes

I’ve been needing to find another car as a daily so I can work and travel to the place where we store my ‘84 RX-7 so I can get her on the road too!

Thanks to everyone on here, I began searching for a 1st gen MS3 for a couple months! Got some work to do to make sure she’s smooth, but I’m super excited!

Also, does anyone know what that light is for in the last photo? Lights up blue and the alarm went off with it when I was messing with the door. I know the car was sold to a dealership and then to another before I bought it, so I was thinking it’s some aftermarket security system.


r/mazdaspeed3 • • 1d ago

HELP 2011 Mazdaspeed 3 – Burnt Valve, Cylinder Head Rebuild, Snapped Exhaust Camshaft, Now Possibly Bent Valves. What Am I Missing?

4 Upvotes

Hey everyone, (long read, sorry)

I’m looking for some advice from people who know these engines better than I do. I’ve been dealing with a pretty frustrating situation with my 2011 Mazdaspeed 3 (2.3L DISI Turbo), and I’m honestly at a loss at this point.

The car has been in the shop since early August 2026 and what started as a burnt valve repair has turned into one problem after another.

I’m not a professional mechanic, so bear with me. I’m going to break down the timeline as accurately as possible.

JUNE 2026 – ORIGINAL PROBLEM

The car started experiencing a rough idle, significant power loss, and multiple trouble codes.

Some of the original codes included:
P0304 – Cylinder 4 misfire
P0300 – Random/multiple misfires
P2187 – System too lean at idle
P0101 – MAF sensor performance
P2177 – System too lean off idle
P0443 – EVAP purge valve circuit

On June 22, a compression test showed approximately 195–200 PSI on cylinders 1–3.

Cylinder 4 had essentially ZERO compression.

A borescope inspection a few days later suggested valve damage in cylinder 4.

AUGUST 2026 – CYLINDER HEAD REMOVAL

August 11: The car went into the performance shop.
August 18: The mechanic removed the cylinder head and confirmed a burnt intake valve in cylinder 4.
The head was sent to a machine shop for repairs.

Parts purchased for the repair included:
ARP head studs
Head gasket set
Timing components
Various seals and gaskets
I paid approximately $X,XXX in August toward the repair.

SEPTEMBER–OCTOBER 2026 – PARTS DELAYS

The repair dragged on because of parts availability and machine shop delays.
At one point, the replacement valves that arrived were incorrect, causing additional delays.
There was also an issue with the head gasket selection. A Fel-Pro gasket was initially involved, but we ultimately switched to an OEM-style multilayer steel gasket.
Eventually, the cylinder head was repaired and the engine was reassembled.

NOVEMBER 2026 – FINALLY RUNNING… THEN DISASTER

Around November 9–10, the mechanic finally had the car running and was conducting a test drive.
During the test drive, the engine lost power, shut off, and started throwing misfire codes again.
After getting the vehicle back to the shop and inspecting it, the mechanic discovered that the EXHAUST CAMSHAFT HAD SNAPPED.
The timing-chain side of the camshaft was still rotating, but the other portion wasn’t moving.
At this point, I was completely confused because the original issue involved a burnt intake valve, not a broken exhaust camshaft.
I tracked down a used replacement exhaust camshaft and had it delivered to the shop.

NOVEMBER 18–20 – REPLACEMENT CAM INSTALLED

The mechanic installed the replacement exhaust camshaft.
The engine started and was running inside the shop.
However, it was throwing trouble codes again.
The mechanic now suspects that some of the EXHAUST VALVES MAY BE BENT OR DAMAGED.
The current plan is to remove the cylinder head AGAIN and send it back to the machine shop to inspect the exhaust valves.
As of right now, we don’t have confirmation of exactly what is damaged.

WHERE THINGS STAND

The car has been in the shop for over three months.
To his credit, my mechanic has not charged me additional labor for all the work following the initial repair. He’s continued trying to get everything sorted out.
I’m not here to bash him or accuse anyone of doing something wrong. I know complicated engine repairs can turn into nightmares, and I appreciate him continuing to work on it.
However, I’m starting to wonder whether we’re missing something important.
The car originally went in for a burnt intake valve. After the cylinder head was rebuilt and everything was reassembled, the exhaust camshaft snapped during a test drive. Now we’re potentially dealing with bent exhaust valves.
I love this car and absolutely want to keep it. It’s also my daily driver, and being without it for more than three months has been extremely difficult for my family.

MY QUESTIONS FOR THE MAZDASPEED COMMUNITY:

What would cause an exhaust camshaft to snap shortly after a cylinder head rebuild?

Could improper timing, a binding camshaft, lubrication issues, or something involving the cylinder head rebuild cause this?

If the exhaust camshaft snapped while the engine was running, could that explain the potentially bent exhaust valves we’re seeing now?

Are there specific things that should be inspected before the head is reinstalled again to prevent another failure?

Has anyone experienced something similar with the 2.3L DISI Turbo?

At this point, would you continue repairing the existing cylinder head, consider a replacement head, or start looking at other options?

I’m trying to educate myself and understand what might be happening before spending more money and potentially ending up in the same situation again.

Any advice from Mazda technicians, engine builders, or experienced Mazdaspeed owners would be greatly appreciated.

Thanks in advance!


r/mazdaspeed3 • • 2d ago

SUSPENSION Rear Suspension Components for "less" clunk

6 Upvotes

Hola,

I have completely replaced all front components (see previous posts) and now I'm thinking about the rear.

Running B14s all around with white line components but the rear clunks A LOT MORE than the front. Would replacing components like camber arms, trailing arms, etc. help with the rear clunks.

I know the platform is notorious for this but there has to be a way to combat it.

Prec


r/mazdaspeed3 • • 2d ago

HELP 2012 not detecting key?

4 Upvotes

Looking for any help or advice. I've got a 2012 speed 3 and suddenly it seems it's not detecting the key fob for push to start. The red key light comes on the dash when the clutch is pressed but never turns green. Fob works for locking/unlocking and I replaced the fan battery. Currently unable to start the car. Tied putting the backup key in the ignition to see if that would bypass or help but no joy. Also tried pressing the fob against the push to start button without any luck. Car battery is good and all accessories come on no problem.


r/mazdaspeed3 • • 2d ago

HELP 2009 MazdaSpeed 3 Problem When Accelerating.

Post image
3 Upvotes

So I’m having the same issues as
u/TackleSweaty2375 and I checked my spark plugs today. All 4 are at 0.030 - 0.031. When I first got the car (a few weeks ago) it had code P2177. I cleared it, then when to try and step on it and code P0303 came on. Only after I stepped on the gas to “do a pull”. The car feels fine at lower RPMs under load and if I’m on neutral and I rev it, there are no issues either. The car does have an aftermarket “Injen” intake. Not sure what to look for without just buying new internals for the HPFP from corksport. I’m also unsure if the car has a tune or not. No access port. HALP!


r/mazdaspeed3 • • 3d ago

SUSPENSION id rather have a blown head gasket than deal with this suspension bs

9 Upvotes

i have replaced alot of my front end suspension i still have random noises when stationary full turning my wheel i hear this popping sound idk what it is then towards the end of full rotation it squeaks not very loud but i can hear it pls what else do i need to replace im actually losing my mind

Bilstein coilover

white line front and rear sway bar and bushing and end links

superpro front control arms


r/mazdaspeed3 • • 4d ago

HELP Weird noise / AC system issue

6 Upvotes

So, car started cooling the inside worse and worse, heat works just fine, same with fan power. Soon after my friend noticed the cooling wasn’t really working like before I started hearing this weird sound that I caught on video.

Don’t know if it’s the compressor or something else but I thought someone here might’ve had the same issue. Was already thinking about fixing a couple things next spring but it’s winter now and I don’t really need cooling rn in Sweden 🤣 so I just wanted to know if somebody knows what this sound is and if it’s bad letting it slide until spring since I don’t have access to a garage rn. I’ll put the clip below, thanks in advance guys peace and love.


r/mazdaspeed3 • • 4d ago

INFO took off my hpfp for my 2009 mazdaspeed 3 should i replace the cam follower?

Thumbnail gallery
3 Upvotes

r/mazdaspeed3 • • 5d ago

INFO CoolerWorx Shifters for Gen 2

Thumbnail gallery
50 Upvotes

Sneak peek of the gen 2 shifter. An attachment to install your boot and hide the shifter will be offered as well!


r/mazdaspeed3 • • 5d ago

INFO What alternator bolts fit the speed 3?

3 Upvotes

I know some of the parts are interchangeable and was curious what I could search for to find the alternator bolts for my 07 speed 3.

Previous owner took the alternator off the car and didn’t leave the bolts behind lol

None of the local salvage yards have any speeds or cx7s with the L3K9, as I assume those are the same.

Any and all help is very much appreciated!


r/mazdaspeed3 • • 5d ago

HELP 2nd gen speed3 problems

3 Upvotes

As the title suggests, I have a few problems with my speed 3, and I’d like to see if anyone else has had the same issues. For starters, I have a 2010 speed3 and the main issue I have found is oil in cylinder 1, and some other gunk in cylinder 4, as well as excessive amounts of oil being burnt. I pulled apart the stock intake and found oil residue in the turbo inlet piping, as well as in the intercooler piping. When I pulled the plugs, cylinder 1’s was dripping with oil, and the rest were pretty well burnt up. I replaced them, and at the same time put in my hpfp internals, cobb 2.5in turbo inlet housing forward intake, and the corksport bypass valve. I had a mechanic do a compression test on it, and he said cylinder 1 had a “slight compression leak,” with the rest being perfectly fine. I was also told a new turbo was put in it before buying the car, however I am not sure which one it is. What should my next steps be moving forward with the car as far as diagnosing what’s wrong with it? Is it worth trying to save this engine, or would I be better off just buying a crate engine?


r/mazdaspeed3 • • 6d ago

HELP i’ve listened to a lot of the mazdaspeed 3 ticking videos but i feel mine has a different tone can someone please clarify whether it’s the same or something different. The noise became prominent after doing a pull before that i couldn’t hear it. it also follows the rpm

16 Upvotes

r/mazdaspeed3 • • 7d ago

PIC Gen 2 at Kanjo Night, Atlantic City

Post image
99 Upvotes

Parked my Gen 1 in the spectator grass area and immediately saw this from across the lot. Nice.

The LB FD3S and the Mazdaspeed FD was cool to see too.


r/mazdaspeed3 • • 7d ago

VIDEO Acceleration test on Autobahn with refurbished injectors. 50-220 kmh

Thumbnail youtu.be
24 Upvotes

Honestly I'm very happy with the results. And now everything is good and no leaks.

Finally.

I wanted to get it all done before GTA 6 comes out lol!


r/mazdaspeed3 • • 6d ago

WHEELS Wheels and Tires + Fitment

2 Upvotes

I had a question about wheels. I want to get some multi-piece five spoke forged wheels, non reps. If anyone has pictures of wheels they think look good and drive good, drop them in the thread. I'm okay with used wheels or retro-made wheels.


r/mazdaspeed3 • • 6d ago

HELP Whats this rattle at low rpm,😭

1 Upvotes

Rattle at low speeds. During cold start and when under load at 1k rpm

Is it timing chair

Is it turbo

Is it exhaust shield (don't think so)

It was due for an oil change. When I checked the level it was below the min on the dipstick. Thought maybe it was the timing chain due to low oil. I did an oil change and the rattle persists.