r/minibikes • • Sep 26 '25

Other AI posts, yes or no?

7 Upvotes

Been getting a few AI posts, so we want to try to get ahead of this before it becomes an issue. Let's vote on it, and we'll make a rule accordingly.


r/minibikes • • May 19 '21

Governors, Flywheels, And An Internet Full Of Crap

137 Upvotes

Taken from this thread.

"This has come up recently, again, so I'm going to post this here. What you are about to read is a couple of articles I wrote sometime back, that address the function of the governor, the exploding flywheel MYTH, and all the crap to go with it. What I have written in based on years of personal experience (not "I heard, read, or was told" as well as extensive research and others' personal experience. It was originally written for the go kart crowd, but the same information applies to all similarly-derived small engines. Take it for what it's worth and insert your favourite fine print here, but I'm telling you- there is so much MIS-information out there, it's disgusting. Grab your favourite beverage, smoke if ya got 'em, and read on...

It is absolutely amazing how often we run into this here- and how often we find ourselves banging away on the keyboard, typing out the same old answers. So, I felt it was a good idea to write up a little blurb on the topic- If requested, I'll sticky it- to hopefully save us all some future work. Let's start by outlining the governor's job description. Everyone knows that the governor tries to limit engine speed to (usually) 3600 RPM. But wait- there's more. The reality of it is this- the governor's job is to try to MAINTAIN 3600, not just limit it. The governor reacts to changing loads on the engine- decreasing throttle if it starts to run too fast, and INCREASING throttle if it starts to bog. This is why it is called a "governor", and not simply a "rev limiter".

Now- On to the question: "If I take out my governor, is the flywheel gonna go off like an atom bomb, blowing semi-molten schmutz everywhere, and killing every living thing in a 15-block radius?"

The short answer is no. The long answer: There are many factors involved here, and each must be carefully considered.

  1. I always advise people that IF they are going to run well above governed RPM, to do it by fully removing the governor's internal mechanisms, and NOT simply bypassing it externally. Many governors are designed in such a way that if over-revved, can suffer component interference inside the crankcase, and/or have internal parts forced right off the shaft and bounce around loose inside the crankcase. Either case can cause severe engine damage. NOT an "explosion", just largely F'd up internals.
  2. IF you are going to run ungoverned with an otherwise stock engine, keep the factory spec valvesprings in place. At a high enough RPM, weaker springs will cause a condition known as "valve float" or "valve flutter". This occurs when the valves cannot slam closed fast enough before the next cycle. This cause compression losses, and as a result, prevents the engine from spinning faster than that point. Valve flutter tends to occur in our engines around 5000-5500RPM. Your results will vary, based on your individual engine, spring condition, etc. Valve flutter occurs at a lower RPM than it would normally take to cause a flywheel mishap.
  3. IF you want to get into RPM ranges HIGHER than this (say 5500+), now is the time to go shopping for high-performance internals. A billet aluminum flywheel, connecting rod, and stiffer valve springs are what's called for. Stiffer springs allow the valves to react faster, so at higher RPM, the valves won't float- NOW things really do have the potential to get a little crazy, so it's time to reach into your pockets for better quality parts.
  4. Your connecting rod is MUCH more likely to fail than your flywheel. I have witnessed MANY more conrod failures than flywheel failures. In fact, I have never seen a flywheel failure. Most here haven't.
  5. Contrary to popular belief, a flywheel is NOT going to vapourize at 3601 RPM. This is NOT why your engine is governed to 3600 RPM. Your engine is governed to 3600 RPM because it is an industry-standard operating speed for all the implements these engines are designed to power. Let's NOT lose sight of the fact that these are industrial stationary engines- made and marketed with the primary purpose of powering equipment. Generators, pumps, power washers, welders, cement mixers, tillers, trenchers, tampers- you name it- and the implement are designed to run at 3600 RPM- So the engines are factory set to 3600 RPM. It's that simple. When a flywheel is manufactured, it is designed to run well above normal operating speed. It's called a safety margin.
  6. NOTHING is 100% guaranteed. You can do everything completely properly, and have a flywheel fail at a "normal speed". OR, you can do everything wrong, and run the he// out of the engine at 7500 RPM on a stock 'wheel for a lifetime and never have a problem. Sometimes, there's just no accounting for "Spit Happens". Write that down.
  7. IF you are running an otherwise stock, ungoverned engine, is it adviseable to avoid excessively free-revving the engine. Use proper gear ratios to keep a bit of a load on the engine at full speed, wide open throttle. Don't try to rev the wee out of the engine with the clutch, chain, or belt off. A load on the engine helps keep harmful vibrations (harmonics) in check. If you have an insanely long, steep downhill stretch in your riding route, back off the throttle going down it. If you hear the valves floating or the engine starting to over-rev, apply some brake force. Coasting too fast can force the engine to spin even faster than valve flutter can prevent.

8.) Inspect your flywheel before removing your governor. A previously damaged flywheel can break apart at a completely unpredictable speed. Damage may not be visible (spit happens) but if it IS visible, replace it.

9) If you have to remove your flywheel for repair/maintenance, remove it properly. Do NOT beat the he// out of it with a BFH or pry on it. Invest in a flywheel puller. Failing that, try the following: Loosen the retaining nut until the nut is flush with the end of the shaft. Now, hit the nut squarely and sharply a couple times with a hammer. Most times, this will do it. You can also aid in loosening the flywheel with mutiple taps around the circumference with a soft-faced mallet or deadblow hammer. Do NOT beat on it with a steel hammer.

10) If you need to hold the engine from turning while you are tightening/loosening a crank bolt or clutch, do NOT wedge a screwdriver or bar in between the flywheel fins. Although this is not likely to crack the 'wheel, a fin could break off. This will throw the 'wheel's dynamic balance off. An out-of-balance 'wheel is just asking for trouble. Same goes for sawing off alternate cooling fins (an old performance trick). If your fins are cast into the 'wheel, don't do it. If you have a Honda, clone or other engine with plastic fins, go for it.

11) Handle with care. Once you have the 'wheel off, don't drop it...

So- Armed with the above information, go ahead and make an informed decision. This guide arms you with what you need to know, to decide whether removing your governor is a feasible idea, and how to handle things if you do. And remember (for all the "Armageddon-is-coming-prepare-to-meet-thy-maker-in-a-sintered-metal-flywheel-induced-world-war-3-esque-everybody's-gonna-die-including-the-cockroaches-in-the-cupboard"-nervous-nellies out there... Spit happens. On the one hand, your stock flywheel will very likely be fine. On the other hand, even a performance parts could fail. Spit happens.

One last point here- For those that may not yet be ready to dive into their engine and come out with a handful of governor parts- Some engines (most notably Hondas and clones) have a VERY user-friendly means of governor adjustment. This adjustment is designed to fine-tune the governed speed to spec, but makes it super easy to gain a few hundred RPM- usually you can bring your GOVERNED MAX to 4000-4200 RPM with the turn of a screw. Your governor will still do it's job, but you'll run a little faster. Locate the manual throttle control on your engine- the little lever you would slide to increase or decrease RPM if you didn't have a remote throtte (gas pedal). Behind that lever is a screw with a spring wrapped around it- Notice how the throttle rests against the tip of that screw when you move the lever to the "fastest" position? Great. Remove that screw. Presto- instant maximum RPM increase- no fuss, no muss.

It is also worth noting that these engines were designed to run at 3600 RPM, day in and day out. If you do run faster, the engine will wear faster. Fact of life. Treat it well, maintain it well, and you'll never notice the potentially shorter lifespan.

Governed Idle FYI

The governor is a seriously misunderstood engine control system. For the greater good, here's a little FYI, an experience I just had. Might benefit someone in the future.

Where were we? Ahh, yes- the governor. Contrary to popular (mis)belief, the governor does much more than limit engine speed to 3600 RPM. Wonder why it's not called a "rev limiter"? 'Cause there's more.

The governor's purpose in life is not so much to limit RPM, but SET it. What's the difference, you ask? (I swear I just heard one of you ask that!) The difference is this. SETTING an RPM means KEEPING it throughout the workload. Let's use a lawnmower for example. You start the engine on your walkway and run the throttle up to max. The governor sets the engine to 3600 RPM, and there is no load (not cutting grass). As you move into the grass, the engine starts encountering a load. The governor allows a throttle increase to bring the revs back up to 3600. Cutting away, you encounter a thick patch over the septic tank. As the engine begins to bog and the revs start to drop, the governor allows the throttle to open more and bring the revs up to 3600. Cool? Great. Going around the corner thru that thick grass with the throttle wide open, you hit that bare spot where the dog keeps peeing. The load comes off the engine, and as it begins to increase, the governor closes the throttle to prevent over-revving and holds at 3600 RPM. Got it?

If you examine your external throttle linkage, you will notice that there is no direct connection between the hand throttle control and the carb butterfly. Governor again. The hand throttle does nothing more than alter the spring tension between the governor arm and the throttle butterfly. Setting the manual control to "Idle" merely alters the spring tension from the governor enough to allow it to SET engine idle speed. The idle adjust screw is the bottom end rev limiter in that it sets the baseline that the governor drops to. I told you that to tell you this:

I recently had a situation that some folks might misdiagnose- an engine that refused to idle properly. After a barrage of time, abuse, and adjustments, the chinese Kohler clone on my kids' kart would not sit at idle. The kart constantly wanted to take off with no throttle input. At a glance, the idle was too high.

Close examination revealed that the idle stop screw on the carb was not doing anything- the butterfly just would not rest against it. If I pushed the lever by hand, it would sit at idle RPM, but as soon as I let go, it would take off again.

I tried to adjust the external governor components to no avail. With the arm off the shaft, something just did not feel right inside the engine. I pulled the engine off the kart and tore it down. I don't even know how to describe what had happened inside, but the governor guts were all over the place- literally.

By some miracle, nothing was really damaged. Short version of the story? I epoxied the "press-fit" governor gear shaft back into the side cover and reassembled everything. I (re-)adjusted the external components, and wouldn't you know it? Idles like it just came outta the shipping container at 1310 RPM, and maxing at 4230 as measured by my optical tach. Food for thought."


r/minibikes • • 3h ago

Other 🏁🔧 More Than Just Mini Bikes! 🔧🏁

Thumbnail
gallery
27 Upvotes

What started as a love for mini bikes has turned into a passion, a side hustle, and something my son and I genuinely enjoy doing together.
I buy, sell, trade, repair, rebuild, and customize mini bikes of all kinds. Whether it’s diagnosing mechanical issues, swapping engines, upgrading performance, replacing parts, or bringing a neglected bike back to life, I enjoy every part of the process.
Over time, my son and I have owned, built, repaired, and ridden more bikes than we can count. Each one has its own story, and there’s something special about seeing a bike we once worked on out there being enjoyed by someone else.
Sure, it’s a business, and providing for my family is part of what motivates me. But it’s about more than making money. It’s about putting smiles on kids’ faces, giving families something to enjoy, and taking pride in the work we do.
One of the coolest feelings is seeing someone genuinely excited about a bike we’ve built or brought back to life. And being able to point at one riding around and say, “Hey, we built that!” or “We used to own that bike!” never gets old.
At the end of the day, we’re not just buying and selling mini bikes. We’re sharing something we love, making memories, and keeping the passion alive, one bike at a time. 🏁🤘


r/minibikes • • 1h ago

Showing Off The Stretched Big wheel Duddlebutt

Thumbnail
gallery
11 Upvotes

A few more pics of the Stretched Doodlebug Big-wheel bobber chopper thingymabobber I threw together for the ones that care. Made a post a few days ago showing what it used to look like with a few of the after pics and specs. This is a few more of how it basically looks now, but I've got a bunch of new parts on the way and looking for some graphics for the tank. If anyone knows of any custom graphics companies that do good vinyl, I think I'm wanting to go with some 80s-90s blues/pinks and maybe yellow, almost like the old Solo cup 'jazz' style design concept??

Also, for those that wonder, it's ENTIRELY too fast for what it is. I keep up with 65mph traffic on the main hwy in front of my current campground I'm staying at easily and that's at less than half throttle once the CVT is up to speed. I'd bet it'll get 70mph+ if I pushed it hard enough.


r/minibikes • • 8m ago

Showing Off My storage unit baja warrior build

1 Upvotes

Never posted my bike on here, but I figure it's cool enough now to do so lol.

Got the frame totally stripped from a Russian guy in my city who found it in a storage unit; the 212 on it had a hole in the block, shocks and tires leaking, and the welds were cracked. I ended up getting a buddy to weld the frame, and I bought a whole new engine with a stage 1 kit, salvaged the original exhaust it came with, lifted the engine and did a torque converter setup, threw new brakes, throttle, etc on, and it's a whole new bike!

Have had some troubles getting the carb tuned perfectly over the last year or two and college has gotten in the way of me messing with it, but I finally got it running right thanks to a new cheapo Amazon carb and jets, and I think it looks/sounds pretty much exactly how I imagined when I started the process. Already got the itch to build a more street oriented bike (that doesn't have drum brakes), but this one will do in terms of terrorizing my quiet neighborhood for now.


r/minibikes • • 48m ago

Tech Question so i js got this new bike and i had to install the brakes

1 Upvotes

so i did, and i thought it was ready to ride until i tried to ride and once i did the throttle got stuck, busted my ass middle of the street, had to shut the bike off completely while panicking. it used to roll through low rpm's off pull but then i realized the throttle spring was loose so i cut it that way it pulls back to idle. but what happened was the bike is now stuck full rpm, any time i start the bike it's just full throttle and i don't know what's going on i cut a chunk of my finger skin off and im about to give up but i just want some help man


r/minibikes • • 16h ago

Tech Question First polishing job give me tips for a better shine

Thumbnail
gallery
17 Upvotes

You can see lil scratches


r/minibikes • • 3h ago

Other Tillotson225Rs Build list/recommendations

1 Upvotes

I have a 225rs Tilli and i want to do more to it. i want to be faster id still like to remain on some spurt of pump gas, e85 93 or 91, or 110. But im not to sure what to do to my motor i was wondering if anybody has previously built one. Idk what to upgrade in my tilli to get what i want. i just want more speed and higher rpm range. i would like to stay on pump gas and still ride it around everywhere. Anybody built one of these? thanks.


r/minibikes • • 16h ago

Other Pretty sure that thing is clapped

Post image
4 Upvotes

r/minibikes • • 21h ago

Tech Question Engine help

Post image
4 Upvotes

It only starts on full choke but dies after popping off, if i can take off full choke quick enough i can throttle it to keep it alive but will die if i dont give it throttle. It does not like half choke either. Ive cleaned this bowl countless times and even cleaned fuel tank and line but always the same issue even if i mess with the idle screw and fuel air mixture screw PLEASE HELP


r/minibikes • • 21h ago

Tech Question New engine issues

Post image
3 Upvotes

Fuel is not coming out of this fitting.when I took off the silver tube 196cc diesel


r/minibikes • • 17h ago

Other nibbi 24mm carb tillotson 225rs 115 and 35 jets

1 Upvotes

cleaned and fixed my carb it put it back together with the same jetting and i can’t get my bike to start. it almost starts and just backfires in the exhaust and it won’t start no matter what i do to the idle or air screw


r/minibikes • • 1d ago

Tech Question Kawasaki fj400

2 Upvotes

Came across a local marketplace deal for one of these engines. I did a bit of digging and found they are/used on an EZGO golf kart. With a few modifications, such as governor delete valve springs, if there even are upgrades available. Some gearing or torque convertor, would this be a good engine to use on a project. Will it have the speed, or is it built for low speed with higher torque?


r/minibikes • • 23h ago

Tech Question Massimo MB200 not starting

Thumbnail
gallery
1 Upvotes

Recently bought a Massimo MB200 from my place of employment and it’s not starting. New to minibikes and these are the settings I have it on. Any help is appreciated.


r/minibikes • • 1d ago

Tech Question Is this bike worth buying for $150?

13 Upvotes

Found this FRP GMB100 near me for $150 and the seller sent me this video, it doesn’t sound right at all. Anyone know what the knocking noise is?


r/minibikes • • 1d ago

Showing Off I revived this old barn find and love it

Thumbnail gallery
17 Upvotes

r/minibikes • • 2d ago

Showing Off Rebuilt

Thumbnail
gallery
27 Upvotes

Just wanted to show off my project here’s the before and after


r/minibikes • • 1d ago

Other whats is this worth ?

Thumbnail
gallery
11 Upvotes

r/minibikes • • 1d ago

Tech Question Not getting power to wheel.

2 Upvotes

I recently bought a 212 Tillotson Stage 1 from GPS. I have a 60T sprocket, 10T centrifugal clutch 3/4 bore (from GPS), and 19’ tires. My frame is a massimo mb200s. Whenever I give it throttle and let go the clutch just rattles making the chain rattle as well. Do I need a crankshaft key? Other than that everything is great this is my only issue. Sorry if this is a dumb question I feel like it will be a minor adjustment.


r/minibikes • • 1d ago

Tech Question should i re-bead this tire

0 Upvotes

Hey reddit, i had a bald ass tire so i put a new one on, to bead the tire i put some gas on it then then started pumping it got it pretty full then when i test ride it i started sliding out and now its leaking should i re bead if and if so what method should i do because the gas one didnt work very well


r/minibikes • • 2d ago

Showing Off Just ported this shredder, what do you guys think?

Thumbnail
gallery
28 Upvotes

r/minibikes • • 2d ago

Other Runs good hit 45

38 Upvotes

r/minibikes • • 2d ago

Showing Off First Bike

Post image
10 Upvotes

r/minibikes • • 2d ago

Tech Question Anyone tried a spring seat?

5 Upvotes

For mini bikes that don’t have rear suspension, is a spring seat the best option?


r/minibikes • • 2d ago

Showing Off Stretched and heavily modified

Thumbnail
gallery
74 Upvotes

Pretty sure my first post was deleted for some reason. Maybe this time it'll stay up in case anyone has questions about the build. This is my heavily modded doodlebug. My brother in law is big into modified minibikes and my neighbor gave me his sons old bike that had a brand new HF Predator on it. I spent a weekend with a sawzall, welding machine and about a grand in parts, and this is what I came up with. Went for a modern big wheel bagger style build.

-Stage 2 GPS Predator engine build kit

-GPS HD forks and tree

-GPS 46 tooth rear 2 piece sprocket and hub adapter

-GPS 12" front wheel w/dot tire

-Nibbi Carb and throttle kit

-Juggernaut TC

-Series 30 CVT

-Dewalt battery power supply mounted under seat w/working brake light and blinkers

Used an old Honda 50cc dirt bike aftermarket fuel tank and petcock. 90cc Tao Tao quad rear hydraulic brake kit. Nibbi grips. Some cheap flip up motorcycle seat off eBay with built in springs. Custom exhaust, chain tensioner, rear fender frame and mount setup, etc. Everything was just thrown together from stuff I had in my shop. I ride this bike almost every day I'm home from offshore, as it travels with me as my pitbike when I'm at different RV parks.