r/openwrt • • 4h ago

Need help with vlan on openwrt

Post image
5 Upvotes

Hi!

My setup is as you see in the picture.

ISP router - Tp-Link Archer BE3600

Main router - mikrotik RB750Gr3

Managed switch - Tp-Link TL-SG2210P V5

AP - Tp-Link Archer C6 with Openwrt

I turned AP into a dumb AP, by disabling DHCP, NAT, etc

So this is what I want it to do

I have vlan 30 for main wireless and 40 for guest wireless. I intend to bind vlan30 to 5ghz ssid(main), vlan40 to 2.4ghz ssid(guest).

the firmware version and the hardware has no DSA, so only legacy method.

I have configured the port to the switch, to be trunk(30,40,99), as well as on the switch side. I also have bind the desire vlan on ssid

but it's not working, I don't know why

I have setup the AP's IP to be of vlan 99.


r/openwrt • • 5h ago

Ubiquiti UAP-AC-M with UMA-D external antenna on OpenWrt: Does it work immediately or need special settings?

Thumbnail gallery
2 Upvotes

I have a Ubiquiti UAP-AC-M paired with the external UMA-D directional antenna.

On the stock UniFi firmware, simply attaching the UMA-D to the RP-SMA connectors isn't enough, you have to explicitly enable the UMA-D antenna option in the controller settings, otherwise it behaves as if only the default small antennas are connected.

I'm planning to install OpenWrt on this UAP-AC-M, and I want to make sure before proceeding:

  1. Once OpenWrt is installed, does the UMA-D antenna work immediately through the RP-SMA ports without any special switch?
  2. Is there any specific configuration needed in OpenWrt (such as setting the Antenna Gain for 2.4GHz and 5GHz) to get proper TX power and full performance from the UMA-D?
  3. Has anyone here actually run a UAP-AC-M + UMA-D setup on OpenWrt? Any issues with signal or stability?

Thanks in advance!


r/openwrt • • 10h ago

Having trouble with network config changes not applying properly - moving ports to another bridge via luci disables them?

2 Upvotes

As per title, I'm having difficulties with openwrt/luci not applying config changes properly :-

I configured a second bridge via LUCI and added WiFi APs and some LAN ports to it, but openwrt doesn't bring the LAN ports up or add them to the bridge after applying changes or rebooting - I have to ssh in and do that manually each time.

It also doesn't apply the gateway setting to the bridge's routing table and I have to do that manually too.

I've poked around in /etc/config/network but I didn't spot any obvious (to me) issues :-

root@OpenWrt:~# cat /etc/config/network
# [… irrelevant entries trimmed …]

config device
		option name 'br-lan'
		option type 'bridge'
		list ports 'lan1'
		option bridge_empty '1'

config interface 'lan'
		option device 'br-lan'
		option proto 'static'
		option ip6assign '60'
		option multipath 'off'
		list ipaddr '192.168.4.1/24'

# [… br-lan and lan1 work fine …]

config interface 'vpn'
		option proto 'static'
		option ipaddr '192.168.5.1'
		option netmask '255.255.255.0'
		option multipath 'off'
		option gateway '192.168.4.112'
		option ip4table 'vpn2lan'
		option type 'bridge'
		list dns '192.168.4.112'
		option device 'br-vpn'

config route
		option interface 'vpn'
		option target '0.0.0.0/0'
		option gateway '192.168.4.112'
		option table 'vpn2lan'

# [… default gateway is not added to vpn2lan table …]

config rule
		option in 'vpn'
		option lookup 'vpn2lan'

config device
		option type 'bridge'
		option name 'br-vpn'
		option bridge_empty '1'
		option ipv6 '0'
		list ports 'lan2'
		list ports 'lan3'
		list ports 'lan4'
		list ports 'lan5'

# [… lan2-5 are not brought up, and not added to br-vpn …]

(config generated by luci web interface, I haven't edited it manually)

and I can't find those LAN ports mentioned anywhere else in /etc other than the board definition/BSP :-

root@OpenWrt:~# grep -R 'lan[15]' /etc 2>/dev/null | grep -v board
/etc/config/network:    list ports 'lan1'
/etc/config/network:    list ports 'lan5'

After router reboot or applying any configuration changes, I need to manually ssh in and brctl addif br-vpn lan2..5; ip link set lan2..5 up; ip route add table vpn2lan default via 192.168.4.112 because openwrt's systems apparently don't do these steps even though as far as I can tell they should.

I'm familiar with linux networking in general (hence ability to manually fix misconfigurations), but not with how OpenWRT goes about doing things (thus unable to make the changes actually stick and be applied properly)

Where else should I be checking for relevant settings?
Is there somewhere I can temporarily put the commands to fix things that'll automatically get run after network config changes while poking at openwrt's system to do it properly?

Am I encountering some sort of bug here? It seems odd that moving ports to another bridge via web interface disables them, and there's no option in luci web interface to re-enable them…

Are any of these issues fixed in 25.12.6, making an upgrade likely to fix stuff? I didn't see anything relevant in the release notes or changelog

Model: GL.iNet GL-MT6000 Firmware Version: OpenWrt 25.12.5 r33051-f5dae5ece4 / LuCI (HEAD detached at 128a7812) branch 26.180.75667~128a781


r/openwrt • • 1d ago

How do regulatory updates work in openwrt?

8 Upvotes

Hi

Say this recently, and it got me thinking, how do any regulatory updates to allowed WiFi bands work on an open source project like this.

This time it's a loosening of the rules, but it's perfectly possible that they could get tightened, leaving users as criminals :)

I wouldn't mind the extra bands as well

https://www.ofcom.org.uk/spectrum/innovative-use-of-spectrum/consultation-expanding-access-to-the-6-ghz-band-for-commercial-mobile-and-wi-fi-services?utm_source=chatgpt.com


r/openwrt • • 1d ago

My IDU 6401 OpenWrt setup – wireless backhaul, performance tweaks, watchdog scripts and a lot of experimentation.

1 Upvotes

Hey everyone,

I've been spending quite some time experimenting with OpenWrt and trying to get the most out of a multi-AP wireless setup.

The idea was to improve Wi-Fi stability, make the wireless backhaul more reliable, optimise performance and automate as many routine tasks as possible.

I've made quite a few changes along the way, so I thought I'd share what I've been working on.

Some of the things I've configured:

Wi-Fi and connectivity

\- Unified SSID across access points.

\- Separate 2.4 GHz channels to minimise interference.

\- 5 GHz wireless backhaul.

\- Wi-Fi client monitoring and recovery.

\- Automatic recovery of wireless interfaces.

\- Dynamic TX power management.

Networking

\- relayd wireless pseudo-bridge.

\- Single LAN subnet.

\- Centralised DHCP and DNS.

\- Backhaul connectivity watchdog.

\- Automatic recovery if the wireless link goes down.

Performance tweaks

\- Hardware flow offloading.

\- PPE/NSS acceleration (where supported).

\- TCP buffer tuning.

\- Conntrack optimisation.

\- Network backlog adjustments.

\- BPF JIT.

\- Memory and CPU governor tuning.

Custom scripts and automation

I've also put together a few shell scripts to handle things automatically:

\- "wifi_client_guard.sh" – monitors Wi-Fi health.

\- "wifi_eco_mode.sh" – manages night-time TX power.

\- "router_maintenance.sh" – handles scheduled maintenance.

\- "backhaul_watchdog.sh" – monitors and recovers the wireless backhaul.

\- "usb-rebind.sh" – attempts to recover dropped USB tethering.

\- "wake.sh" – Wake-on-LAN utility.

\- "led-manager.sh" – manages router LEDs.

Other tweaks

\- DNS redirection and local adblocking.

\- BanIP integration.

\- USB tethering support.

\- USB 2.0 mode configuration where supported.

\- TTL/Hop Limit rules for tethering interfaces.

\- Automated recovery and maintenance tasks.

I'm still experimenting with some of these settings and don't consider every tweak universally beneficial.

I'd especially like to hear from people who have experience with OpenWrt on different chipsets.

A few things I'm curious about:

  1. Is relayd reliable enough for a long-term wireless backhaul?
  2. Which hardware offloading implementations actually make a noticeable difference?
  3. Are there any sysctl settings you'd recommend changing or avoiding?
  4. What's your approach to maintaining stable wireless connectivity?
  5. Any recommendations for better watchdog implementations?

Would love to hear your suggestions, improvements or even criticism. Always interested in learning something new about OpenWrt.

Thanks!


r/openwrt • • 2d ago

Flint 2 vs deco be65 with pi-hole

4 Upvotes

Im going to invest in a router for the first time. It is fibre 1000/1000 internet, 2 floor wooden structure house.

I found openwrt to be interesting but I lack knowledge. Maybe flint 2 with mt-3000 beryl's connected only by wifi to create a mesh or just flint 2 to start to see if it covers full house

Or

Use Raspberry pi 4 and do the pi-hole thing with deco be65 (black friday deal) and use 2 pack and second device would be connected to the pc because it does not have its own wifi receiver.

I just like linux and all the control and features. I hate when companies stop update products. Probably not big on vpn but maybe.

Is flint 2 worth it investing in 2027, is pi-hole good enough? Is deco a bad brand? Any input would be helpful!


r/openwrt • • 1d ago

Who are all those packages for?

0 Upvotes

I can't understand why anyone would need 99% of the packages, are they mostly for security hardening or what is their purpose? I looked through a lot of them and ended up installing like 5 that had obvious benefits but I don't get the other ones. If you use niche packages, what do you use them for? Are there any packages that you feel like people are missing out on?


r/openwrt • • 2d ago

Adguard home on a R6900 v2?

3 Upvotes

So I read that it uses alot of storage and can wear out the router memory if I try to squeeze it onto the onboard.

The router has a usb 3.0 port on it.
Should I figure out about using a usb for it, use an old Patriot Torq 2 64 gb usb 3 adapter ( It's in the parts drawer I know it's bad by today standards 😂 or should I just try out the lite ad block ?

I live in a mobile home and so would be work to try and mount and actual hard drive to the usb port.


r/openwrt • • 3d ago

I missed my Fritz!Box DECT integration so I patched it back

31 Upvotes

Disclaimer #1: I'm an actual developer, with ~20 years experience.

Disclaimer #2: yeah, I made it with an agentic coding enabled IDE, I actually work this way from something more than a year. It's not AI Slop, I know what it is doing, creating, writing, I can read and correct the output, I could have done without it but I did not care enough and not had this amount of spare time, so I never did it before.

Full story.

I have two Fritz!Fon DECT C5 phones. I love them, they are beautiful, have a snappy interface, large screen, and always worked better than my Grandstream cheap DECTs.

I have a full OpenWRT based network, 1x Banana Pi BpiR3 main router, 1x Fritz 7530, 1x Archer C7, 1x Zyxel AX3000. I felt the 7530 wasted after converting it to OpenWRT (mainly a dumb AP for DAWN).

So I fired a Claude Code chat and started looking around for decompilation projects for Fritz routers. I quickly come across to Rockstein2/FRITZ.Box_7530-08.25-kernel-4.4.271-telephony-re/ that sped up the initial process and starting from it I slowly added back more and more DECT functions to my 7530.

I set the path for the coding agent to use non invasive loading (no reflashing), LUCI meta package for big resources already available (like Asterisk) and slowly walked the path up that hill.

  • Currently working: DECT pairing, contacts, call history, outgoing SIP calls with audio, DTMF, router thermometer, English/Italian LuCI. Voicemail and C5 settings pass automated tests.
  • Not implemented: Fax, transfers/conferences, email forwarding, Internet apps, USB recording storage, DECT Eco and RF telemetry.
  • TODO: Physical verification of voicemail, C5 settings and alarms; real incoming SIP test; remaining advanced options.
  • Missing: Analog telephony (won't look into it, not interested actually), firmware flashing, Git repo (using proprietary AVM components ATM, will look into reverse engineering them in the future)

r/openwrt • • 3d ago

OpenWrt switch performance

11 Upvotes

Hi gang,

Just want to see how switching performance & stability compares to vendor firmwares. Looking to soon buy a PoE switch, primarily looking at D-Link switches, but also open to suggestions.

Thanks in advance


r/openwrt • • 2d ago

Help Me Flash JDU 6J11 In Pune.

1 Upvotes

Hello Experts ,

I have two Jio routers with firmware updated to November 2025 or later. Because of this, the restore option is unavailable, preventing me from flashing OpenWrt using SSH mode or the password trick.

It seems the only remaining option is using UART, which I am unable to perform myself.

I would appreciate your assistance with the following:

  • Local Help: Is there anyone in Pune who can assist with hardware/UART flashing?
  • Alternative Solutions: Are there any alternative software workarounds available for this firmware version?

My intended use cases for these routers are:

  • Wi-Fi Extender
  • Ad Blocking
  • Basic NAS
  • Mobile Tethering

Please let me know if you have any suggestions or if you can help


r/openwrt • • 2d ago

DHCP not responding on one interface - I need another pair of eyes

1 Upvotes

OK, I have a setup with 4 interfaces:

lan - 4 hardware ports - managed by DHCP for IP addresses

wifiap - one wifi interface that serves as an AP - managed by DHCP for IP addresses

cell - (Wan on most other routers) this has a cell modem attached

trm_wwan - Wifi interface managed by Travelmate

Cell and trm_wwan are also monitored by mwan3 for routing.

Everything works fine except that lan will not respond to DHCP requests. I can see them coming with tcpdump but dnsmasq never responds. The config for wifiap is identical, and it hands out addresses just fine.

I've looked through everything and I know I'm missing something simple but for the life of me I don't see it.

root@RosyBelle:/etc/config# cat network

config interface 'loopback'
option device 'lo'
option proto 'static'
list ipaddr '127.0.0.1/8'

config globals 'globals'
option dhcp_default_duid '0004806d06fcd0364a509f052b9c66b5dcbf'
option ula_prefix 'fd09:8e28:1df::/48'
option packet_steering '1'

config device
option name 'phy2-ap0'
option mtu '1500'

config device
option name 'phy1-sta0'
option mtu '1500'

config device
option name 'br-lan'
option type 'bridge'
list ports 'lan1'
list ports 'lan2'
list ports 'lan3'
list ports 'lan4'

config interface 'lan'
option device 'br-lan'
option proto 'static'
option ipaddr '192.168.116.1'
option ip6assign '60'
option multipath 'off'
option netmask '255.255.255.0'
option gateway '192.168.116.1'
option dns '192.168.116.1'

config interface 'wifiap'
option device 'phy2-ap0'
option proto 'static'
option ipaddr '192.168.173.1'
option ip6assign '60'
option multipath 'off'
option netmask '255.255.255.0'
option gateway '192.168.173.1'
option dns '192.168.173.1'

config interface 'cell'
option proto 'dhcp'
option device 'wan'
option sendclientid 'auto'
option multipath 'off'
option metric '200'

config device
option name 'phy0-sta0'
option mtu '1500'

config interface 'trm_wwan'
option proto 'dhcp'
option metric '100'
option sendclientid 'auto'
option multipath 'off'

config interface 'trm_wwan6'
option device '@trm_wwan'
option proto 'dhcpv6'
option reqaddress 'try'
option reqprefix 'auto'
option norelease '1'
option sendclientid 'auto'
option multipath 'off'
option metric '150'

root@RosyBelle:/etc/config# cat dhcp

config dnsmasq
option domainneeded '1'
option boguspriv '1'
option filterwin2k '0'
option localise_queries '1'
option rebind_protection '1'
option rebind_localhost '1'
option local '/lan/'
option domain 'lan'
option expandhosts '1'
option nonegcache '0'
option cachesize '1000'
option authoritative '1'
option readethers '1'
option leasefile '/tmp/dhcp.leases'
option resolvfile '/tmp/resolv.conf.d/resolv.conf.auto'
option localservice '1'
option ednspacket_max '1232'
option filter_aaaa '0'
option filter_a '0'
list interface 'wifiap'

config odhcpd 'odhcpd'
option leasefile '/tmp/odhcpd.leases'
option leasetrigger '/usr/sbin/odhcpd-update'
option loglevel '4'
option piodir '/tmp/odhcpd-piodir'
option hostsdir '/tmp/hosts'

config dhcp 'lan'
option interface 'lan'
option start '100'
option limit '150'
option leasetime '12h'
option dhcpv4 'server'

config dhcp 'cell'
option interface 'cell'
option start '100'
option limit '150'
option leasetime '12h'
option dhcpv4 'server'
option ignore '1'

config dhcp 'wifiap'
option interface 'wifiap'
option start '100'
option limit '150'
option leasetime '12h'
option dhcpv4 'server'

config domain
option name 'rosybelle.lan'
option ip '192.168.116.1'

config dhcp 'trm_wwan'
option interface 'trm_wwan'
option ignore '1'

config dhcp 'trm_wwan6'
option interface 'trm_wwan6'
option ignore '1'

root@RosyBelle:/etc/config# cat firewall

config defaults
option input 'ACCEPT'
option output 'ACCEPT'
option forward 'ACCEPT'
option synflood_protect '1'
option drop_invalid '1'

config zone
option name 'lan'
option input 'ACCEPT'
option output 'ACCEPT'
option forward 'ACCEPT'
list network 'lan'

config zone
option name 'wifiap'
option input 'ACCEPT'
option output 'ACCEPT'
option forward 'ACCEPT'
list network 'wifiap'

config zone
option name 'outside'
option input 'ACCPET'
option output 'ACCEPT'
option forward 'ACCEPT'
option masq '1'
list network 'cell'
list network 'wifi4'
list network 'wifi6'
list network 'trm_wwan'
list network 'trm_wwan6'

root@RosyBelle:/etc/config# cat mwan3

config interface 'trm_wwan'
option enabled '1'
list track_ip '8.8.8.8'
list track_ip '8.8.4.4'
option reliability '1'
option count '5'
option timeout '5'
option interval '10'
option down '5'
option up '1'
option initial_state 'online'
option family 'ipv4'
option track_method 'ping'
option size '56'
option max_ttl '60'
option failure_interval '20'
option recovery_interval '5'

config interface 'cell'
option enabled '1'
list track_ip '8.8.8.8'
list track_ip '8.8.4.4'
option reliability '1'
option count '3'
option timeout '5'
option interval '10'
option down '5'
option up '1'
option initial_state 'online'
option family 'ipv4'
option track_method 'ping'
option size '56'
option max_ttl '60'
option failure_interval '20'
option recovery_interval '5'

config member 'primary'
option interface 'trm_wwan'
option metric '1'

config member 'backup'
option interface 'cell'
option metric '2'

config policy 'failover'
list use_member 'primary'
list use_member 'backup'

config rule 'default'
option dest_ip '0.0.0.0/0'
option use_policy 'failover'

config globals 'globals'
option local_source 'none'


r/openwrt • • 3d ago

I’m desperately looking for GL-AR300M (128MB NAND version

2 Upvotes

High there! I’m desperately looking for GL-AR300M (128MB NAND version), which is not available any morr. GL-AR300M16-Ext is has only 16MB NOR storage and it’s not enough for my use case. Does anyone know where I might get one, or have one still around looking to sell it? I’d really appreciate it. I’m based in Poland.


r/openwrt • • 3d ago

Looking for new wired router

2 Upvotes

Hello

Just had a qotom router fail, and im looking for a new wired router. The optical cable from my ISP goes directly into the router. Im looking at 2 paths here:

  • a router with 1 normal SFP port, and 5 x 2,5gb ethernet ports
  • a managed switch with VLANs and at least 1 SFP port, 8 x 2,5 gb ethernet ports, take the optical into the switch and out to a separate router with 2 ethernet ports, then back to the switch on a different VLAN.

Any recommendations for hardware here?

edit: my internet is only 300mbps, and i use wireguard for VPN. im looking for 2,5gbps because my server and computer is 2,5gb


r/openwrt • • 3d ago

I need help openwrt doesnt wanna dawload A1300

1 Upvotes

I'm trying to install OpenWrt on my GL.iNet GL-A1300 router using the official U-Boot recovery method and the official firmware from your website. However, I keep getting an error, even though I'm following the instructions on your website step by step.

I've also tried updating the firmware through LuCI, but that doesn't work either. All my software and firmware are already up to date.

I've tried multiple times, using the official files and following the recommended procedure, but nothing seems to work.

Could someone please help me figure out what I'm doing wrong or why the installation keeps failing?


r/openwrt • • 4d ago

bridged access point? [eli5, noob]

Thumbnail openwrt.org
2 Upvotes

I've used these instructions to configure a second router (B), to connect to a existing wifi (A).

What I want is for (B) to be isolated from (A), so that devices connected to (A) cannot see or use devices connected to (B). Almost as if (A) was the guest network, unable to use printers or NAS in network (B).

Is this a suitable way to do that? How could I test if (B) is properly isolated?


r/openwrt • • 4d ago

Cudy WR3000P (SN 2624) – WAN port dead / not recognized on OpenWrt, forcing LAN fallback. Any fixes for newer hardware revisions?

2 Upvotes

Hi everyone,

I recently installed OpenWrt on my Cudy WR3000P v1 (EU version), specifically unit with serial number starting around 2624.

As known from some other Cudy/MediaTek devices, the 2.5G WAN port (which also handles PoE-in) is giving me a hard time. On a fresh OpenWrt installation (25.12.5), the WAN port remains completely dead—no link, no reaction to the cable, and dmesg | grep -i eth shows no eth interfaces at all (only the internal switch and wireless interfaces).

Right now, I am forced to use a workaround by using LAN 1 as a fallback WAN port, which works fine for data. However, since the WR3000P supports PoE, I really want to get rid of the separate power cable and use the actual WAN port to power and feed the device cleanly.

  • What I've checked:

    • dmesg shows no signs of the 2.5G PHY being initialized properly (likely a Clause 45 / Realtek PHY / MediaTek bridge initialization issue similar to other RTL8221B / MT7981 reports).
    • Given the newer serial number (2624), it seems like a silent hardware revision update from Cudy where the device tree might need an update.

Questions:

  1. Has anyone with a newer Cudy WR3000P revision managed to get the 2.5G WAN port working?
  2. Are there any specific patches, custom DTS tweaks, or kernel flags required for these newer board revisions?
  3. Would jumping to a very recent master snapshot fix this, or is it a known pending issue?

Any advice or pointers would be greatly appreciated!
Thanks in advance.


r/openwrt • • 4d ago

Old-school install clarification

6 Upvotes

I just picked up a WRT54G V2.0 for like, nothing. Yes yes I know this is ancient and considered EOL in latest releases, but I only plan to use it as an extra 802.11G network and I had a lot of success with these devices some years ago and it's not like they've broken in the meantime.

The wiki seems to have gotten a little confusing on these older devices -- it says the latest installable version is 19.07.10 but then starts veering into discussion of 10.03.1 in the actual install instructions, while sort of having multiple edits debating the correct procedure in the article text...and a mention of having to install a 2.4-kernel based image before upgrading to brcm47xx which I'm not sure whether really applies or not...it all just seems to have bit-rotted a tad, does anyone still mess with these devices to clear things up?

https://openwrt.org/toh/linksys/wrt54g?s%5B%5D=page


r/openwrt • • 5d ago

I got my OpenWrt APs to show up as UniFi APs in the controller. It mostly works, and I need help testing it on hardware I don't own

60 Upvotes

Hey all,

So I have a UniFi gateway at home (UCG Ultra) but I didn't want to buy UniFi APs when I already had perfectly good routers running OpenWrt. I found jonasevcik's openUF project, started poking at it, and over the last few months it turned into my own version that I now run on both APs in my house.

Repo: https://github.com/yesrab/openUF

What it does right now: the controller adopts the OpenWrt box like it's a U6 In-Wall, pushes my SSIDs, VLANs and radio settings to it, and shows clients, signal and traffic like it would for a real AP. Fast roaming, band steering, min RSSI, speed limits, and client block/unblock work for me. There's also a small LuCI app and an installer script.

What I'm honestly not sure about, and where I need help:>

- I've only really lived with it on JioRouter AX6000 (mediatek filogic) and tested on a couple of old TP-Links (Archer C5 v1, WDR3500). If you have something else and an afternoon, I'd love to know if it even adopts.

- I don't own a single real UniFi AP. Roaming between openUF and genuine UniFi APs is done through d-malinowski's plugin and I'm trusting his testing, not mine. If you have a mixed setup, you're exactly who I need.

- Guest portal, rollback when a config push breaks wifi, encrypted syslog to the controller, and device SSH login were added recently and have only run in a VM. They're off by default for that reason.

- It needs about 16 MB flash. 8 MB devices don't fit the crypto library. If someone knows a clean way around that I'm all ears.

I'm not a networking pro, so if you look at the code and think "why on earth did he do it like that", please tell me. Issues, PRs, or just "it broke on my X" are all welcome. A lot of what's in there came from other people already (jonasevcik's original, d-malinowski's roaming work, and antoniocosta's unifi-openwrt, which was posted here recently and does the same thing in Go).

Not affiliated with Ubiquiti, it never flashes their firmware, and it's GPL.

Thanks for reading. Happy to answer anything.


r/openwrt • • 5d ago

The current Mbed TLS developers are looking for new maintainers to succeed them. Otherwise, they'll abandon their TLS and X.509 libraries in April 2027.

Thumbnail lists.openwrt.org
88 Upvotes

r/openwrt • • 6d ago

Where can I read about how to set up a LUCI statistics plugin definition?

5 Upvotes

This page has some information that I believe got me pointed in the right direction for making the data readable by RRDtool, but now I think I have to figure out how to tell RRDtool what graphs I want, and I can't find any actual documentation on how to do that. I know I need to put something at /www/luci-static/resources/statistics/rrdtool/definitions/exec.js and there are other examples in there that give me the general shape of the file, but I can't figure out how it works just from reading the examples.


r/openwrt • • 7d ago

Meraki MX100 opnwrt router

8 Upvotes

I found a cheap Cisco Meraki MX100 on Facebook should I buy this and install openwrt. On website it says it’s a generic installation how hard is this installation I assume it’s easy.


r/openwrt • • 7d ago

Change the WAN-Ports Mac-Address

2 Upvotes

With my Fritz!Box 7530 AX running the default firmware, I was able to get a new public IP address after a reconnect. This no longer works with my Fritz!Box 7520 running OpenWrt, and in Network > Interfaces I see a CGNAT IP. I found out that this might be caused by the router's MAC address, so I want to change it to the MAC address of my old Fritz!Box.

When I click 'Edit' on the WAN interface, under 'General Settings', there is an option called 'MAC Address'. When I enter the MAC address there and restart the WAN device, the connection drops and won't come back up. There is no other field to change the MAC address. How can I fix this?


r/openwrt • • 7d ago

[Part 2] Rescued my Soft-Bricked my ZTE ZXHN F670L - Just to fall into another rabbit hole

Thumbnail gallery
35 Upvotes

Hey Guys,

Surprise Surprise, Now I'm porting openwrt to ZTE F670L.

[Short Summary]

I was able to rescue my soft bricked router using TFTP upgrade method. But soon found out that changing anything in rootfs causes crc error and bricks the device.

So, I'm adding this device's support in openwrt and use for my usecase, which was to share mobile internet using Eth Tethering.

Current Progress?

  • Flashing using TFTP
  • System Boots
  • Both 2.4 and 5 Ghz WLAN work
  • Able to access the LuCi Dash

[Long Story]

  • After getting the UART serial reader, I tried many combinations but was getting gibberish data, similar to what other people have seen with ZTE routers.
  • I was able to read the Serial logs by using USB metal housing as GND.
  • Could not two way communication to work, but from the logs and tinkering with the reset switch, I got to know about TFTP upgrade mode.
  • Luckily found "V1.1.20P3N6B" firmware and unbricked the device
  • Upon customizing again, I found that changing anything in rootfs causes CRC check error and bricks the device.

This caused me to abandon the stock firmware and try porting openwrt for this.

Why openwrt? Idk, I'm new into this and I knly know about this rn.

As of now, I am able to

  • Successfully flash and boot into openwrt firmware.
  • Start both 2.4 and 5 Ghz Wlan
  • Started with a custom html page served using httpd but now Luci dashboard is being served correctly.

Current target is to get LAN to work. Post which my usecase can be achieved.

I'm mostly vibe-coding my way through this, so I'm not sure I'll be able to answer any question, if someone asks. Pls expect a AI paraphrased response.

I'll also add the Agent's work summary in comments.