r/paint • u/AssPainting • 22h ago
Advice Wanted Any tips or tricks to getting between two door casings in a corner that has less than an inch of space at the widest point? They're not plumb.
r/paint • u/AssPainting • 22h ago
r/paint • u/traildoginthedesert • 21h ago
We hired a licensed contractor to repaint our home’s exterior in Phoenix for $5,500. Our contract specifically states Dunn-Edwards SPARTASHIELD eggshell, but they used ACRI-HUES instead. They left behind partially used 5-gallon ACRI-HUES buckets.
I was clear about wanting quality paint that could withstand the Arizona sun. I even had 12 gallons of Sherwin-Williams SuperPaint and specifically requested something equivalent.
The job is finished and paid for. I’m leaving the state for three months, so having it repainted isn’t practical.
I’m not trying to cause problems, but I do expect to get what I paid for.
How significant is the difference between these paints, and what would be reasonable compensation?
r/paint • u/psychonautalot • 16h ago
I own a painting business and keep running in to some big daddy projects, this being the largest (not really because its just the trim/eaves/sills) but its still a massive 8k sq ft home. I've got all my numbers for the labor, just looking for some options for breathable, vapor-permeable 100% acrylic exterior coatings and maybe some people with experience coating EIFS Dryvit. I know dryvit makes their own coatings, but sourcing them in North Idaho is next to impossible apart from freight shipping it or driving 5 hours. Looking for some alternative options. Ty in advance painters!
r/paint • u/guptashubham123 • 20h ago
We have a 3D wave feature wall made of 3 panels of green moisture-resistant MDF (HDHMR) with 2 vertical joints as shown in photo. There is a split AC right above it and an LED strip along the bottom edge.
What was done so far:
1st attempt: Putty → primer → texture paint. Cracks appeared along both joints.
2nd attempt: Opened the joints, sealed them with black M-Seal (rigid 2-part epoxy putty), then applied primer → putty → primer → texture paint.
Two issues showing up after \\\~1 month (see photos):
What is the best way to permanently fix both the joints and the blistering without tearing down the wall? Any suggestions are appreciated.
r/paint • u/Interr0gate • 23h ago
I want to color match this grate to my new floor but it's pretty cruddy, dirty, paint flaking, etc. what is the best way I can refinish this for paint? I called a couple sandblasting and painting places and it's about 80-100$ to refinish it with sandblasting and powder coating. I could get a brand new one for 90$ but it would be dark brown, so I'd have to paint it still anyways. I think it's not worth it for me to do that for this (not that their skills are too expensive, just not worth it for me). Can I like dunk this in a solution or something to strip everything? Or maybe I can just try to get someone to sandblast it cheap then paint it myself?
HI all,
Other than replacing the trim, how can I address a crack like this at a baseboard joint?
This one was filled with a Bondo-style wood filler when the grain on the trim was filled prior to paint. It was done in the summer, and now that winter's setting in, the crack has started to form again.
Trim has been in place for 15+ years. I believe this is a butt-style joint.
Should I try to re-fill and re-paint during the dryest part of the winter? Caulk doesn't seem appropriate at this type of joint, but I could try that too.
Thanks!

r/paint • u/khartwel • 14h ago
I recently patched where my mantel used to be to place another mantel. Did the patch 3 coats with new drywall and tape on the big holes then primed, and painted 2 coats. Looked perfect. I then put the mantel in and there was a significant gap between the wall and mantel. I didn’t want to use caulk because it would look weird painted that far onto where the mantel started so I used wood filler. Sanded it smooth but the sanding unfortunately left divots in the drywall where the wood filler met the wall so I repatched the divots. 2 coats of mud, sanded, applied primer, then 2 coats of paint. Well once the paint dried the edges where the paint met the wood filler was peeling so now I’m stuck with this. My plan is to rerepatch, sand, prime, and paint. I really don’t want to go through this again if it’s just going to be the same result. What am I doing wrong? My only thought is that I either didn’t let the primer properly cure (waited at least 15 hours before the first coat of paint) or I didn’t get the primer low enough where the wood filler and patch meet. Help please amateur here.
r/paint • u/notslim-justshady • 17h ago
Hi everyone just wanted to come one and ask for some advice as a first time home owner who’s trying to do repairs. About a year ago when I first moved in I had to patch up a few holes in the walls, sand it down, texture spray it, then prime and paint and it was alot of work for just one room so I had been procrastinating painting other areas of the house. However, I decided to start the living room make over recently so I’m at the texture spraying part prior to painting, and I didn’t have a mask on hand so I tried to make it quick, I did a quick makeshift mask using my shirt and held my hand over my mouth and nose and quickly went around the room spraying and quickly went outside and left the front door open to help with ventilation. About 15-20 minutes later I went back in trying to start cleaning up, I tried using my industrial vacuum (with the fine particle filter) but it didn’t seem to work well so I decided to just use a wet rag along the baseboards to clean up any of the bigger particles that fell to the floor (still using my makeshift shirt mask and hand) I got a bit tired and out of breath so I tried to keep it quick and I didn’t want to go back inside to wash my hands so I used the water hose outside when I got a dry cough attack. I took a few breathes and eventually it kinda got better it started turning into like a wetter cough? and I felt the need to clear my throat you know?? anyways I decided to go in turn the fans on and open the windows and leave the house for a few hours, I’ve been breathing fine but I feel mild throat irritation and I’m worried about sleeping back at my house. I think tomorrow I’ll be getting a mask to continue working but I’m curious is there any symptoms I should look out for? How do I know if I’m actually okay following potential exposure? As you can tell I’m a bit of a newbie and a slight hypochondriac so just wanted to see if anyone can offer some reassurance or any advice, thanks in advance!
r/paint • u/notie547 • 2h ago
Best/easiest way to fix these gouges? scrape flat, mud, prime, paint?
I'm not a pro painter and it doesnt need to be perfect.
What would be a good paint color for my walls? I have a tan velvet headboard and I would like my bedding to be olive green or have green accents. the floors are gray. The room is east facing but doesn’t get much natural light. I’m not very adventurous so would like a neutral color
r/paint • u/Decent-Educator7881 • 12h ago
My bathroom has very old paint that obviously wasn’t meant for a bathroom (like that when we bought the house). I want to paint over it but it’s very crack, some paint is even coming up at the dry wall. I’ve read some places that I’ll need to totally strip the old paint, but someone suggested I just put a thin layer of something called mud plaster on the walls to seal the cracks (and spackle the bad parts) and just paint over that. That sounds way easier to me than stripping all the paint. Is that possible? Or do I need to totally strip the paint?
r/paint • u/bro4klyn_syz • 13h ago
r/paint • u/AbilityComfortable58 • 13h ago
It’s such a hassle and pain to deal with
r/paint • u/Wonderful-Gazelle-68 • 16h ago
Long story short, used W-D 40 on a storm door hinge & now need to prep for new paint color . Any tips would be appreciated.
r/paint • u/negulous_shorts2 • 19h ago
Planning to paint my moldy bathroom ceiling, what do you think about my plan?
The wooden ceiling has moldy spots. I clean it regularly but after a month or so the mold starts to bloom. It's clearly not going to be possible to get all the mold off this ceiling permanently no matter how clean and dry I am able to keep it, the mold is in the wood. Fortunately it's nice and dry above this ceiling. I would take the wood down and replace with sheet rock but given the way the ceiling is constructed it would be a nightmare.
My thought was to clean the wood thoroughly with vinegar, paint with a mold-killing primer and then a mold-killing bathroom paint. Am I missing anything here? Anything else I should be aware of?
Thanks!
r/paint • u/absentori • 19h ago
Recently got our bathroom halfway redone (new tile, shower + vanity install). Open to any colors, just don't want to wash out the tile or vanity. We can't decide on anything!
r/paint • u/Impossible-Drop23 • 21h ago
Hi paint experts! I need some help. This is a Sherwin Williams Emerald rain refresh new exterior paint job. I noticed some of this odd sort of crackly appearance in spots and some drippy discoloration . Do you know what could cause this? Is this a repaint situation? Thanks for your help!!
r/paint • u/Brevvvv17 • 3h ago
Me and my mom have been trying to get a beige color to paint my room, but all the beige we've tried always turns out slightly pink or to a hue of it