r/printers • • Dec 19 '24 Bravo

Discussion The truth about printer subscription programs and many misconceptions about them

155 Upvotes

Dear all,

I work in the printer industry. For a very well-known consumer products manufacturer that gets discussed on this sub a lot.  I will not disclose which manufacturer I work for, nor will I disclose any manufacturer I do not work for (since the industry is relatively small eliminating 1 or 2 will make it generally too obvious as to which I do work for) as I am not officially speaking on behalf of the company. But, I want to set the record straight on subscription programs because some of you are drastically misinformed and it is very frustrating to see as someone who understands these programs as well as basic logic.

There are two types of subscription programs. Each of the major consumer manufacturers offers at least 1 of these programs, some offer both.

The first type of program is an auto-reordering program. The printer can tell (via various ways depending on each manufacturer) when the ink / toner is low and when it hits a certain point that will trigger an order of the ink/toner that device uses. Most manufactures that offer this will first send you an email letting you know that an order has been triggered and it will allow you to skip the delivery of the consumable and thus not get charged. If you allow the order to go through you are purchasing that consumable. That consumable is yours, you own it, just as if you walked into a Staples, Office Depot, Best Buy, or bought it on Amazon… You can cancel the “subscription” the next day and continue to use that consumable until it is empty.

The second type of program is a true subscription program. **THIS** is what many of you are vastly misinformed and / or are irrational about. In this program *you are not purchasing a consumable* at all. You are paying the manufacturer for X number of pages per month. The manufacturer will send you a consumable to use because the printer needs ink / toner to work but, that is not what you are paying for. You are paying the manufacturer $Y per month to print up to X pages per month.. that’s it. Of course you can print over that X number and pay an overage (just like years ago with cell phones).. and of course, you can print under that X number and some pages will roll-over to future months (just like years ago with cell phones). The owner of the consumable is the manufacturer. You never bought it, you never owned it. Therefore, it is not yours to use after you end the subscription! The only reason most manufactures do not ask for it back is because they don’t want to pay for shipping it back to them. But, they still own it… not you.  You can think of this like renting an apartment. You are paying a landlord $X per month to live in their building. The landlord is providing the building for you to live in while you are paying rent. You do not own the building. and when you stop paying rent you are no longer allowed to continue living in the building. Just like your Netflix subscription, Apple TV subscription and Disney+ subscription.. when you stop paying for the subscription, you stop getting to use the service. Just because while you were paying you had access to the content does not mean you at any time owned that content and get to continue watching it once you stop paying the subscription.

I truly hope this helps clarify somethings for some of you. Others I understand are lost causes but, I will do my best to answer any questions I can.


r/printers • • 16h ago Popcorn

Other Interesting?

Post image
97 Upvotes

r/printers • • 5h ago

Troubleshooting Troubles with my thermal printer

Post image
3 Upvotes

I recently posted about my thermal printer only printing slightly (check previous post for pics) but now after reading people’s suggestions, I have kind have made something work. In the picture down below is what it looks like with a lower print size. I have checked that everything was 4x6 but lowering it down seems to be working better than I would have imagined. The best I could get was the 4x1, anything after that was resulting in the same problem. If you guys think of anything please let me know!


r/printers • • 14h ago

Rant I have six 3D printers, no issues. But “normal” printers…

Post image
15 Upvotes

This Epson hit my limit. Then hit the floor.

Never buying another Epson or HP printer. HP was even worse.

I went with a Brother laser since that’s what I’ve had in my office for years without any issues. Had it up and running within 5 minutes.

I hate all of the bells and whistles they force onto you. Especially in the software. I don’t want any cloud services, a firmware update every other day, five different applications on my computer.

Just print the damn thing.


r/printers • • 1h ago

Troubleshooting Brother inkjet error message “the printer couldn’t print the _PrepartoryJob____”.

1 Upvotes

I have had a Brother MFC-J995DW INKvestment Tank Color Inkjet for about 8 years now and have LOVED it. I used to do a lot of graphic printing and the colors have always been so vibrant - not so much in the last year. Recently, I’ve been getting an error message saying “the printer couldn’t print the _PrepartoryJob____”. However, after a short delay, it will print, but output quality is lessened, even though I have all the settings set for best quality. I’m not sure of exactly when this started to happen, but I have had both a brother firmware update and a windows (11) update during this time. Could either of those updates caused this problem? I would also like to note that the ink I’m using is more than a year old. I will happily purchase more ink if I was sure that the old ink is the problem, but I am reluctant to spend that money if its not the real issue. Has anyone else had this message and solved the problem? Thanks.


r/printers • • 16h ago

Other Tired of ink-wasting 'power clean' cycles on tank printers, I built Nozzle Guardian: an open-source driverless anti-clog daemon

17 Upvotes

Hey everyone,

I bought a tank printer (EcoTank) specifically to stop being extorted by expensive ink cartridges. But if you own an Epson EcoTank, Canon MegaTank, or HP Smart Tank, you know the unspoken curse: go on vacation for a week, and one of your color nozzles clogs.

When this happened to me, the printer's only built-in solution was a "Power Cleaning" cycle. It ran for 15 minutes, made a racket, drained nearly a third of all my ink tanks straight into the waste maintenance box, and threatened to brick the printer when the waste sponge filled up. All of that just to clear *one single dried nozzle*.

I decided that was absurd, so I built **Nozzle Guardian** — a lightweight, completely autonomous daemon designed to keep printheads permanently fresh with surgical efficiency.

### What makes it different from standard test pages:

  1. **Zero Wasted Paper (The 3mm Micro-Stripe):** Instead of spitting out a full-page color pattern, it prints a tiny 3 mm micro-line at the absolute top margin of the page. You can literally keep the *exact same piece of scrap paper* sitting in the rear feed tray and reuse it 50+ times.
  2. **Channel-Decoupled Purges:** If you print black-and-white documents every day, your Black channel never dries out. Nozzle Guardian tracks dormancy per color channel. If only Cyan/Magenta/Yellow have been idle for 6 days, it purges *only* CMY in pure color pass. It never wastes ink creating composite black, and never flushes channels that are already healthy.
  3. **Driverless & Zero-Bloat (Pure IPP):** It speaks raw Internet Printing Protocol (RFC 8011) and PWG-Raster directly over your Wi-Fi/LAN. You don't need CUPS, proprietary vendor drivers, or bloated desktop print suites running.
  4. **Home Assistant Native:** Comes with ready-to-use MQTT/REST sensors and 1-tap actionable mobile notifications ("Color nozzles dormant for 7 days. Tap to run 3mm purge").

The project is 100% open-source under the MIT license:

👉 **GitHub:** https://github.com/umbette/nozzle-guardian

We also set up an automated community compatibility tracker in the repo — if you have a tank printer (Epson, Canon, HP, Brother) and try it out, please let us know how your model behaves!


r/printers • • 1h ago

Troubleshooting Horizontal double lines on my Pixma Pro 200S

Post image
1 Upvotes

I’m getting very faint horizontal double lines on the black ink and photo magenta, always in the same spots across nozzle checks.

I’ve tried aligning the print head both auto and manually, running a deep clean, running a regular clean and the ink is genuine

Is this a print head problem? Is this something that can be fixed?


r/printers • • 1h ago

Discussion Small Business Budget Friendly Laser Printers Black Friday Shopping

1 Upvotes

What would you like to accomplish?

I'm looking for a laser color printer without carriages. I also have had TERRIBLE luck with canon printers locking me out of them using 3rd party ink. I have bought 2 canon printers in 5 years and do not intend to buy another. I have not heard good things about HP and online reviews are poor.

I am needing a printer for business cards, photo printing, and stickers.

I want to find a printer where the refillable ink or its alternatives are also affordable and not subscription-based.

Are there any models you are currently looking at?

Epson & Brother

More Details:

QuestionsAnswers
Budget:Max $200
Country:U.S.
Color or black and white:Color
Laser or ink printer:Laser
New or used:New
Multi-function:not necessary
Home or business:Small business at home office
Printing content:Documents, cardstock, photos, stickers
Printing frequency:50 pages/mo
Pages per minute :don't care
Page size:Letter
Device printing from:PC
Connection type:wifi

r/printers • • 2h ago

Troubleshooting Help with 150 Laser and Wifi

1 Upvotes

Hello,

I was wondering if anyone can help me with a printer I am ready to throw against a wall.

I have a 150nw laser, it’s actually quite good, except for one problem. Whenever something is unplugged or if there is a power cut, it loses any sort of connection and reconnecting is a pain in the ass.

There was a power cut a few weeks ago, it only lasted for a few minutes and I can’t get the printer back online.

The printer itself works, I can print a test page. When I try to connect to a Windows laptop via USB, windows recognises the printer but says there is an error… unfortunately it doesn’t say what the error is. I haven’t tried on a mac yet.
Whenever I try connecting via my routers WPS button, nothing happens.
The next thing I am trying is to connect to the printers own wifi network ‘DIRECT-E2-HP Laser 150nw’. I can connect, but it asks for a password I don’t have. Apparently it is supposed to be on the test page but I can’t find it (I can see wps pin and network key, but both passwords are invalid).


r/printers • • 6h ago

Discussion Canon Poxma: Holes in photo paper - fixable with better paper?

Post image
1 Upvotes

Hello, I have a canon Pixma G7050. I'm printing photos for the first time, on a cheaper photo paper. The printer makes these holes for transporting the paper through the printer.

When I buy the good, canon photo paper, will they be there, too, or is this a paper issue?

Thanks a lot in advance!


r/printers • • 6h ago

Troubleshooting Printing artifacts and missing elements when using PDF-XChange with a Ricoh IM CW2200 – compatibility issue?

0 Upvotes

Hi everyone,

I’m experiencing a serious and rather strange printing issue with a Ricoh IM CW2200 plotter when printing architectural drawings from PDF-XChange.

With certain architectural PDF plans, the printed output contains additional hatching, shading, or other graphic artifacts that are not present in the original PDF. These artifacts appear only in the printed output and can make parts of the drawing look completely different from the original.

Even more concerning, on some printing attempts, certain text elements and dimension lines (cotes) have completely disappeared from the printed output, although they are clearly present in the original PDF.

I have already tested both an older and a newer version of PDF-XChange, but the issue still occurs.

As a temporary workaround, I tried printing the exact same PDF files using Adobe Acrobat, and in that case the artifacts and missing elements do not appear. The drawings are printed correctly.

This makes me wonder whether the problem could be related to:

- PDF-XChange's PDF rendering/printing engine;

- the Ricoh printer/plotter driver;

- the plotter's PDF processing/RIP software;

- compatibility between PDF-XChange and the Ricoh's printing workflow;

- certain PDF elements such as transparency, clipping paths, vector objects, layers, hatches, fonts, or complex architectural linework.

Has anyone experienced a similar issue with a Ricoh IM CW2200, especially when printing architectural/technical PDFs?

I would really like to find the underlying cause and a stable, long-term solution. I need to be able to rely on the plotter to reproduce all the information contained in a PDF accurately, including text, dimensions, hatches, vectors, layers, etc.

I am not looking for a workaround that simply flattens or rasterizes the PDF/image, as this can reduce the quality of architectural drawings and is not an ideal solution for technical documentation. I would prefer a solution that preserves the original vector information and print quality.

At this point, I would also appreciate recommendations for a reliable PDF viewer/printing application for architectural and technical drawings, if PDF-XChange is known to have compatibility issues with this type of plotter.

Does anyone know if there is a specific PDF-XChange setting, Ricoh driver setting, RIP/plotter configuration, or PDF processing option that could solve this permanently?

Adobe Acrobat currently works correctly with the same files, so I suspect there may be a difference in how the two applications process/render the PDFs before sending them to the plotter.

Any suggestions, technical explanations, or similar experiences would be greatly appreciated.

Thank you!


r/printers • • 7h ago

Discussion Fucked up a printer, don't want to do it again with the next one

1 Upvotes

Hello I had been a user of a Brother DCP T720dw for at least 2 years, using it as a small business, it worked like a charm, no problems aside from few paper jams until i broke it, I was making 1000 presentation cards( I know don't tell at me) and after finishing the job my printer never worked the same again, the alignment was off and then I didn't print anymore; I didn't took proper care of it by not letting it cold down and the thermostat broke(at least that's what my technician told me I don't know if it had something else but I believe it) it was a hefty chunk to get it repaired so I just had to wait to get the moment to buy another one and I will be getting the Brother DCP T730dw and I really don't want this to happen again to my new printer, so I ask, what's you guys advice to keep a healthy printer if you are using it for a stationary business or something alike? I see many people using similar printers for the same thing but they dont seem to have issues even after printing lots of stuff, what's the limit of pages per day you print (full color) and what the cooling period ? This might seem very stupid to ask but I don't want to waste my money again with such expensive equipment:(


r/printers • • 10h ago

Troubleshooting Hp officejet pro 6968

Thumbnail gallery
1 Upvotes

r/printers • • 10h ago

Troubleshooting Help! Canon Pixma ix6820 potential nozzle or print head clog!

Thumbnail gallery
1 Upvotes

I got this printer about a year and a half ago and I print stuff about twice a month - mostly stickers on glossy sticker paper.

Recently (<2 months) I have noticed that my prints come out with white streaks on them and my print quality is worse when I set the print quality as ”best”. Best quality is giving me very faded colors and normal gives me more accurate colors but white streaks. My prints are no where as vibrant as they used to be before (photos attached).

I have done 2 nozzle cleans and one deep nozzle clean and the print checks are getting worse instead of better! I am currently waiting 24 hours before running another deep nozzle clean. I also notice some ink splotches sometimes. Please help!

Note - I run my prints using the same settings as always using the system dialog. I use third party ink but I have had successful results with them for more than a year.


r/printers • • 14h ago

Other Canon Selphy Photo Collage Tool

Post image
1 Upvotes

Made a tool today that takes photos and arranges them on a grid, so that 4x6 printers can print wallet photos etc for photo journaling. Pretty handy to choose photos from my phone, arrange / zoom / crop in a 4x6 preview that accommodates the 4x6 selphy perforations, and print right from iOS. Shows dates like early digital cameras too.

Likely could be nice for 4x6 printing at Wallgreens or on other home 4x6 printers as well! Figured I'd post so that "Selphy" might return this as a search result.

Website: https://bmitchinson.github.io/photo-grid-creation-tool/
Source Code: bmitchinson.github.io/photo-grid-creation-tool/


r/printers • • 14h ago

Troubleshooting Printer not recieving any power after cleaning.

1 Upvotes

Good day guys, ion really ask for help on here, but here goes. I had my epson et-15000. I disassembled, and clean it. Where I then proceeded to connect back the cable, and screw back up all the parts in the respective correct order. However, when I put in the printer into the power outlet, and proceed to turn it, I'm not receiving any power at all. Any solutions I can try, also I live in a third world country, so I'd like to bot go to a repair shop, which would be expensive.


r/printers • • 15h ago

Purchasing A3 or A4 Laser Printer Recommendations

1 Upvotes

I'm looking to upgrade my Samsung CLX-6260 colour laser multifunction printer and would appreciate some real-world feedback from people who have used any of the models below.

I've been researching both A3 and A4 printers, including some inkjet options, but I'm leaning towards staying with laser unless there's a compelling reason to switch.

My requirements:

  • Maximum available shelf depth: 620mm.
  • Colour multifunction printer (print, scan and copy).
  • Primarily printing documents, presentations, charts, graphics and the occasional photo.
  • Print quality is a major priority, particularly sharp text, clean graphics and accurate, consistent colour reproduction.
  • Home use, generally under 500 pages per month.
  • Looking for something that offers a noticeable improvement in print quality over my current Samsung CLX-6260.

Models I'm currently considering:

PrinterFormatTechnology
Brother MFC-J6975DWA3Inkjet
Epson EcoTank ET-16600A3Inkjet
Canon MF667CdwA4Colour laser
Brother MFC-L8930CDWA4Colour laser
Canon MF754Cdw IIA4Colour laser
Fujifilm Apeos C2450SA3Colour laser
Kyocera ECOSYS M8124cidnA3Colour laser
Kyocera ECOSYS M8130cidnA3Colour laser

I'm particularly interested in the Fujifilm Apeos C2450S, as I've read good things about Fujifilm's image-processing technology, but I'm unsure how its actual print quality compares with the other manufacturers.

A few questions:

  1. Has anyone owned or used any of these models? What has your experience been with print quality?
  2. Which manufacturer produces the best colour output for presentations, charts and graphics?
  3. Are there any other A3 or A4 colour laser multifunction printers I should be considering that have a depth of no more than 620mm?

I'm not particularly concerned about print speed. I'd much rather have excellent print quality, reliability and reasonable running costs.

I'd appreciate feedback from anyone with hands-on experience, particularly comparisons of actual printed output rather than just specifications.

Thanks!


r/printers • • 21h ago

Purchasing Office Printer

3 Upvotes

I was asked to make a list of "commercial" printers for my boss to consider. We don't do enough printing and scanning to need a $3k printer, though. We currently have an OfficeJet Pro 8720 and 7740, which work okay. Some team members with MacBooks don't like that they can't scan to their computers using the touchscreen.

Most of our documents have our logo and branding colors. I want it to support duplex printing and duplex scanning. We have been buying HP ink cartridges, so it's okay if the printer has to use OEM toner.

HP LaserJet Pro 4301fdw, Canon ImageClass MF753CDW II, and Brother MFC-L8930CDW have come up in my searches. Most everyone recommends or says Brother is always the answer. I bought my church an MFC-L8930CDW last year. I don't like iPrint & Scan software for our scanning process, and often scanned documents have a line on them.

Staying with HP would be easier because everyone has the software installed, and Best Buy includes HP products in its Recycle & Save program. I've only run across negative reviews on the 4301, which makes me hesitant to recommend my boss ordering one.


r/printers • • 15h ago

Troubleshooting Canon TS6400 color misalignment on nozzle check

Post image
1 Upvotes

I ran a nozzle check on my Canon TS6400 and i can’t fix the color misalignment, please help!


r/printers • • 1d ago

Purchasing Looking for laser printer

5 Upvotes

Hello! I’m looking for a compact laser printer that doesn’t have pricey toner, monochrome is fine, duplex printing isn’t necessary but a plus, I only print about 10 sheets per month so laser is necessary:) I would also like to be able to print wireless. Any suggestions are greatly appreciated. I’d like to avoid any printer that requires an ink subscription. Thank you! Would prefer not to spend more than $150 and am hoping to find a deal for Black Friday. I was looking at:

Brother HL-L2405W
Brother HL-L2460DW


r/printers • • 18h ago

Purchasing Looking for a home color printer - recommendations?

1 Upvotes

Hi, so I am looking to buy a home color printer. Have a couple young kids, we do not print frequently (have not had a printer for years and just go to in-laws to print occasionally) but kids are now getting to age where we want to print out our own worksheets to practice HW.

While doing research, it seems like laser is the way to go. Yes?

Also, no real need to scan things, but I could see rarely wanting to scan some old photos. Though it sounds like a dedicated separated scanner for ~$100 or so would be better that we can put away when not in use?

What are people's recommendations?

- how is the Brother HL-L3280CDW?

- should I choose Canon equivalent? Something else?

Thanks!


r/printers • • 18h ago

Purchasing Purchase - The best card laser printer to get that isnt absurdly expensive?

1 Upvotes

Ive been making my own playing cards for a while now
(mtg proxys specifically for those who know what that is)
including fancy stuff like foils.

However the whole process is kinda annoying since my current laser printer (HP color laser mfp 178nwg) cant print on anything above 160gsm so i have to manually glue them on a proper backside after and it can't properly print on foil sheets at all.
(the workaround i found was to print on transparent sticker sheets and then stick those on top the foil but it'd be much easier to just print on the sheet directly)
And despite saying it prints at 600dpi i cant notice the difference between an A4 thats printed at the maximum dimensions that an A4 at 600dpi goes up to (5k x 7k pixels) and one thats shrunken down to half that size (it is set to "best" already and i couldn't find any other settings after ALOT of trying) which needless to say makes me pretty suspicious of the printers actual quality so thats another reason i wanna switch.

Ive looked at some models but none of them had any images or videos of them actually doing the printing or the resulting cards so they might as well all be as good as each other for all I'm concerned.

Minimum Requirements:

- Budget: Since the models I've looked at are hella expensive i probably just want to go with whatever is the cheapest that fulfills my requirements and save up for that. I'm more concerned about the price of the toner, if i have to re-buy toner for each color at like 50 bucks individually thats not realistic for me (off brand stuff is fine if its available for a printer this specialized) I suppose the first say 5 toner refills (of all the colors collectively) should also be considered in the price, a more expensive printer with cheaper toner would be less expensive in the long run given that i print alotta cards.

- Country: Germany.

- Color or black and white: Color. Would be rly cool for foils if it also had white toner as an option but i know thats probably a pipe dream.

- Laser or ink printer: Laser (hell, maybe even UV if thats a thing for cards i dont know much about them tho).

- New or used: dont rly care, if it works it works.

- Multi-function: As long as it can do the one thing I'm buying it for its fine.

- Duplex Printing: Would be cool but not needed by any means.

- Home or business: Home.

- Printing content: Detailed card images (600dpi at minimum).

- Printing frequency: Printing for boosters or a deck or some other project usually comes in bursts so one week I'm not printing anything the next I'm printing like 200 cards (ergo 23-ish pages since 9 cards fit on one page) overall i would guess I'm printing about 100-600 cards per month depending on if i have some project going i need them for but with a new printer like this making it easier that number prolly goes up a bit.

- Pages per minute: dont rly care.

- Card size: 63x88mm exactly.

- Device printing from: PC.

- Connection type: Id prefer smth i can actually plug in to my PC but if i have to do it with wifi thats hardly a deal breaker.

- Paper: Needs to be able to handle high gsm card stock (like somewhere between 300-400 gsm)

Lastly it needs to actually print on the entire card, no left over white edges.
If i have to manually cut them out after printing anyway i may as well use my current printer.
Blank card in, finished card out, thats the goal.

I wish there was more info about printers like these out there like even just a video of one printing or smth cuz at the moment i have no idea weather these expectations are unreasonable or not.
If there is no printer that fits these but you know of another option that seems at least adjacent to what I'm looking for do tell I'm all ears!

Ive for a long time made my own card game cards with my laser printer but id rly like to upgrade to a printer with which i dont have to cut/glue cards out after printing. It would be rly nice if i could just fill it up with the blank cards and just whenever be like "yep print this card image" and out comes the finished card


r/printers • • 19h ago

Purchasing Looking to purchase a simple printer with scanning capability for at home zine making.

1 Upvotes

I would like a printer for my art studio to make zines.

  • Budget: $150
  • Country: USA
  • Color or black and white: b&w (but ability for color could be nice)
  • Laser or ink printer: leaning towards laser, not quite sure
  • New or used: new
  • Multi-function: yes
  • Duplex Printing: yes
  • Home or business: home
  • Printing content: text, scanned images, drawings, and small photos for zine making
  • Printing frequency: a few pages a week
  • Pages per minute: n/a
  • Page size: 8.5x11
  • Device printing from: laptop & phone
  • Connection type: wifi for laptop and phone, and laptop usb

extra details:

I would like to be able to scan photos and drawings, and experiment with the scanner itself for fun effects. I wouldn't need to scan anything larger than 8.5x11. I would prefer something low maintenance and not have to download an app or something in order to use the printer.


r/printers • • 20h ago

Troubleshooting Canon pro 300 nozzles

Thumbnail gallery
1 Upvotes

Hi, I had bought the Canon pro 300 off of eBay (I know, I have my regrets). At first when I did a nozzle print test, only 2 colors printed. I did 2 cleanings and a few more colors showed up. The first image is after 2 cleanings and a deep cleaning. However, during each cleaning it cuts short with the error message from the second image. Are my nozzles clogged after the printer was unused for who knows how long? What should I do about the error message? Thanks so much.


r/printers • • 20h ago

Troubleshooting Epson ET 8500 lines

Thumbnail gallery
1 Upvotes

Hello! I bought an Epson ET 8500 off facebook marketplace ab a week ago, it wasn’t printing anything at first so I ran it through some print head cleanings, then eventually a power clean, then a print head alignment. (Extra info, it’s level, has right paper settings, and printing on right side of paper, paper is sublimation paper)

The only problem I’ve having seems to be with the black. I’ve tried doing some head cleanings to just see if that might help, but there’s been 0 change between cleanings. Anyone have something else for me to try..?