r/recumbent • • 2d ago

What causes death wobble on a trike (other than the obvious)?

8 Upvotes

My wife has a Catrike Pocket. It's always been well behaved. We put it away when we started the process of moving and just started riding again this week. Somehow, in storage it developed a nasty habit! It has extreme steering wobble/shake after any perturbation, no matter how minor. It does not appear to be speed related, other than needing to be above about 8mph to have it happen at all. Without an impulse destabilizing it, it's perfectly well behaved all the way up to 40mph. Unfortunately, any sort of upset will send it into convulsions. Small crack, pothole, pebble on road, etc will send it shimmying so hard that the wheel is turning back and forth 4" each side of center. It does not easily die out once it gets going. Yesterday and today, my wife had to resort to jamming a thigh against the steering arm to be able to ride it. She's got bruises from it because it'll kick so hard.

I checked the normal stuff that I've seen come into the shop on customer trikes:

  • The headsets for both kingposts are tight enough there's no play
  • There's no play in the tie rod
  • The alignment is reasonable
  • The front wheels are true

So once you get past the obvious stuff, what can cause a death wobble this severe?


r/recumbent • • 3d ago

Hase Kettwiesel - make controls on steering bar higher?

3 Upvotes

Hase Kettwiesel (2015) has under-seat steering. A central horizontal rod is on a pivot, and connects to the steering rod which goes to front wheel. On both sides of that rod there are 22mm diameter L-shaped tubes. The L-shaped tubes can be moved in and out a few centimetres. The controls mount to the vertical part of these tubes.

On left there is a brake.
On right there is a brake (and parking brake lever), Shimano Nexus gear shift, Bafang motor control and display unit.

These controls are a bit too low for the rider - they can reach them, but cannot easily see the display etc.

Any idea on improving? I suppose I could get a kit provided to mount on bicycle handlebars which provides a short 100mm bar onto - typically used as a place which you can put lights, bike computer etc, and then shift the Bafang display to that.


r/recumbent • • 11d ago

Tips for a beginner?

Post image
31 Upvotes

Just got my first bike of this type. I am 34m and love riding bikes but never rode this one before. I rode a little bit today and loved it! Trying to get a hang of it. Having trouble with turning and hills. I found it with the sign free on someone's lawn. I used wd40 on the chain, checked all the nuts and bolts to make sure nothing was loose and it was good. What is some things I should know to continue using this bike. I love it so far and very happy to use it. Any advice helps :)


r/recumbent • • 11d ago

How do yall do work on your recumbent? Is there a stand made for flipping recumbents over to work on?

10 Upvotes

I am considering adding a rear hub motor to my early-2000s model Hurley bent bike.


r/recumbent • • 13d ago

❄️Winter is coming❄️ I'd like to bring my trike indoors for the winter and use it as an exercise bike. Has anyone done this? If so, how did you set it up?

11 Upvotes

I'm looking at stands and rollers at the moment, but open to all the options.


r/recumbent • • 12d ago

Hase Kettewiesel c.2015 User Manual wanted

1 Upvotes

Just acquired a second hand Hase Kettwiesel from about 2015. Looking for any documentation which is around.

Hase trikes are single wheel in front, two behind, sometimes called Deltas.

The pedals drive the rear right wheel only through a Shimano Nexus type 7 speed hub. (Later models have something like a differential, so both rear wheels are driven). Brakes are cable operated disks on both rear wheels, no front brake.

This model did not originally have electrical assistance - but that was added by the dealer - a Bafang motor on the front wheel.


r/recumbent • • 15d ago

My touring setup!

Post image
96 Upvotes

Just did the GAP/C&O trail on this setup. I’ve ridden that route a few times in the past, but not since my injury driven move to recumbents a few years ago. Performer Goalx 26, loaded for cold weather camping (carrying most of the gear for two here) My only mechanical issue the whole time was a broken chain tensioner spring which I discovered a few minutes after taking this picture. Stuck a spare spring in and kept going. Rohloff/SON hubs, with everything set up for one armed use. 26x2.1 tires, I’m the original builder of the wheels and had them on an upright bike for at least a decade before moving them to this bike


r/recumbent • • 15d ago

storage A rack for free space!

Thumbnail
gallery
58 Upvotes

hoping this may eventually move closer to the door versus the patio.. but I made a quick lumber recumbent rack. Wanted to share.


r/recumbent • • 14d ago

Broke my PR and set the fastest speed in a Strava Segment. 36.7 mph.

Thumbnail
gallery
5 Upvotes

r/recumbent • • 16d ago

Idler or jackshaft

1 Upvotes

So I am working on a ehpvc competetion and we are making a recumbent bike. So the problem is that is we have a difference of opinion on using a jackshaft or a idler. We have a requiment that the bike participates in a drag race and endurance race also. What is the best option a jack shaft or an idler ?????


r/recumbent • • 17d ago

Sanity Check Before I blow $100 on this upgrade

Thumbnail
gallery
7 Upvotes

I upgraded the front and rear idler sets on my TerraTrike Tour 2, and everything sounds less grindy than before, but I am considering getting the items shown in the first picture (my shopping cart at t-cycle.com) to make the rear set float, thus (hopefully) making it even quieter.

Currently, I have a bolt pushed through a non-threaded hole in the frame, then through an L-shaped chain keeper, a spacer, an idler, a spacer, an idler, a washer, and a nut.

The exposed part of the bolt is not long enough to give the idlers any lateral space to float -- there is barely enough length to screw the nut all the way on.

It seems that the components in my cart would position the idlers in a better spot (left to right), would give me a longer exposed bolt so the idlers could float, and would introduce nicer (quieter) chain keepers. Is that all correct?

Also: I am thinking I could do a cheap test of how much improvement floating would bring by just swapping in a longer 8mm bolt, omitting the chain keeper, and leaving everything else the same. What do you guys think?

Any other advice or insights for this inexperienced tricyclist? Thanks!!


r/recumbent • • 18d ago

Catrike Village Chain Tube optional?

7 Upvotes

So I snagged a used villager. Installed a longer beam for my tall self and proceeded to tune the bike that had been in storage for some time. The chain tube broke free and lodged in the idler gear and then twisted a link breaking the chain.

No big, two links out (because I always forget to leave the pin in on the first link) and removal of the tube results in being back on the road. Is this optional? It appears to protect the rider from chain contact. I will snag a new one from Utah, but between now and then it appears to ride just fine with only the idler and the bottom tube.


r/recumbent • • 19d ago

Riding in the rain

9 Upvotes

I live in the Pacific Northwest I would like to ride throughout the year but it gets really wet here. I'm relatively new to recumbent trike riding I was wondering what everyone uses for rain protection, is there after care for the trike when riding in the rain and lastly braking when it's wet what's the best combo to prevent a spin out or uncontrolled stop.


r/recumbent • • 20d ago

Sinner Demon

Thumbnail
gallery
64 Upvotes

About a month ago, I bought my first recumbent bike – a Sinner Demon.

The whole thing started with my neighbour, who's been riding a Challenge recumbent for years. He let me try it a few times, and I guess that was enough to get me hooked. Eventually, I spotted a good deal on a used Sinner Demon, grabbed it, did some repairs and adjustments, and hit the road.

One month later, I can honestly say I'm loving it.

It's lightweight, nimble, comfortable and demonically fast. I'm having a blast riding it, and I really can't imagine going back to a regular upright bike anytime soon.

But here's the funny part.

About 3 weeks after I bought mine, the same neighbour went out and bought a Sinner Demon too. Almost identical to mine – the differences are pretty much cosmetic.

So now, instead of one recumbent rider in the neighbourhood, we've got two nearly identical Demons cruising around Warsaw.

And honestly, seeing pedestrians' faces when the two of us ride together is priceless. I think we look less like cyclists and more like some kind of tiny recumbent cavalry squadron. 😂

Anyway, just wanted to share my first-month experience. If you're thinking about trying a recumbent, I'd say go for it!

Oh, and one more thing! If anyone happens to have a Sinner Demon owner's manual, technical documentation, specifications or any old brochures lying around, I'd be incredibly grateful if you could share them. I've been trying to find some documentation online, but with Sinner apparently no longer around, it's not that easy.

Any help would be awesome!

Demon squadron, assemble! 😈


r/recumbent • • 22d ago

I stopped this guy in Milano

Post image
74 Upvotes

r/recumbent • • 29d ago

Old Linear Limo Seatback Fix

Post image
12 Upvotes

The fiberglass spreader rod on my seatback finally died after 30+ years. The tips were splintering and the rod would not stay in place.

I stopped at my local hardware store to see if they could order a piece of solid, 1/4” fiberglass rod.

The store owner looked at my old piece and grabbed a driveway reflector stick. It is exactly what I needed.

I just cut it to length with a rotary tool. Fits perfectly!


r/recumbent • • 28d ago

I would like to discuss a recumbent tandem build

Thumbnail reddit.com
1 Upvotes

r/recumbent • • 28d ago

Can I can I put 20 inch rims on a 26 in high racer?

1 Upvotes

It has disc brakes.


r/recumbent • • 28d ago

Best recumbent exercise bike with moving handles in India

Thumbnail reddit.com
0 Upvotes

r/recumbent • • Oct 21 '26

How to attach a smartphone?

4 Upvotes

Good morning! I have a Catrike Villager and I am trying to find a good way to attach a large smartphone (Galaxy S23 Ultra). Any ideas on ways to do so or places to attach one? The smartphone holder I ordered from Utah Trikes wasn't big enough, sadly. Thanks!


r/recumbent • • Oct 20 '26

Maddog trike

0 Upvotes

I just got a maddog trike I want to change the rear rims I know I can change the bolt pattern with a hub adapter, but I wanna know if these dimensions will fit****
Wheel Size: 14x7
Center Bore: 72mm
PCD (Bolt Pattern): 4x101.6mm
Offset (ET): -25mm
Any help


r/recumbent • • Oct 18 '26

Cheap(er) DIY Trike Stand

Post image
50 Upvotes

Bought 2 sets of 3 ton jacks for about $60 total and a $7 can of plasti-dip spray. Sprayed the cradles with plasti-dip and now I've got a portable, easy stand that I can access with a mechanic stool on the ground or higher up on a table or platform. ​

There are some great DIY options but even the metal fence pole stand costs about $200 in materials. Meanwhile, I can even quickly pack these in the car if needed.


r/recumbent • • Oct 19 '26

Recumbent trike riding near Rydal,Georgia

Thumbnail reddit.com
1 Upvotes

r/recumbent • • Oct 17 '26

Speed on recumbent trike

12 Upvotes

I had a bad crash last week and I'll be off my bike for the balance of the year.

For a variety of reasons I'm considering moving to a recumbent trike because they're more stable.

But I also want to be able to ride around the same speeds/distances I did this year. So 20-25kph on a 45km ride and and 16-20kph for the 200km over two days ride I want to do in June.

To give you an idea of my riding style/capabilities I have a Cannondale aluminum Synapse 1 and my gravel bike is a Trek Crocket Disc 5. So I'm not bombing along with a carbon frame and matching wheels. My goal is outside of my big rides to do 100-150km a week.

Would a trike like a Catrike 559 work for me? Am I going to be able to keep up with riders doing 25kph on flat roads?

Obviously a trike is an investment so I need to get a good understanding before I put down money.

One note: we had a TerraTrike Rover and it was an interesting ride. I didn't hate it but I didn't love feeling like it was going to tip on corners and it was set up for my wife who's a foot shorter than me so I didn't use it too much.