r/CarHacking • u/Treypopj • 23h ago
Original Project Think I finally finished my android auto project in my OEM Chevy Sonic radio
I will provide details in the comments if you want.
r/CarHacking • u/Treypopj • 23h ago
I will provide details in the comments if you want.
r/CarHacking • u/Global-Might8676 • 12h ago
I've been building Cardashly, an Android car dashboard designed for mounted phones, tablets, and Android head units (Android 8.0+).
Core dashboard features are free to try, with an optional Pro upgrade for extra themes and customization.
If anyone here runs it on a mounted phone/tablet, an aftermarket head unit, or with an ELM327 adapter, I'd love feedback on what breaks or what OBD2 PIDs and dashboard cards you'd want added next.
Link: Cardashly on Google Play
r/CarHacking • u/chrismin13 • 13h ago
r/CarHacking • u/arneabin18 • 15h ago
Hey everyone,
I have a B8 A4 Concert 3 radio and I'm trying to get it to turn on outside the car. I can't find the CAN message that tells it the ignition is on.
Has anyone got a CAN capture from the radio's bus (infotainment CAN, 100 kbps) from the moment the ignition goes on? Even a few seconds of a log would help. Any B8 or B8.5 A4 or Q5 with a Concert or Symphony radio should do.
I'd also love to know if anyone has run one of these on the bench and what they sent it.
Happy to share whatever I find once I get it working. Thanks!
r/CarHacking • u/Duncansport • 15h ago
For a while now, I've been thinking about a way to adapt a starter generator to my old Mercedes as a way to help off the line acceleration and smoother, quieter starts. I see these units every day in my shop, and most of them have no problem starting modern direct-injected gas motors or diesels, so I know it's possible. Next up was finding one that would work. It's pretty close in size to the OM606 alternator. This one puts out 60 Newton meters at the pulley, so obviously, if you do the calculations, it'll be more than enough torque to turn the motor over.
It's taken a few days, and ultimately, some people on OpenInverter had some success and was able to use some of that information through Google Gemini and Argon and finally get it to speak to the CAN-USB. Once we were able to speak to it, I was able to suss out some of the CAN messages and what they were responsible for. At this point, I had a very rough dashboard that was working. At this point, I'm basically giving it full bus power, 12 volts, to turn it on and then basically limiting the maximum amount of torque that it can impart on the pulley because it'll just spin out of control without a motor on it.
So the next step is to adapt it to Baldur's DSL1 (this is what is running my OM606 now) using a CAN32 interpolator since his control unit, being open, can configure the CAN for a lot of great stuff. I'm near certain I can set this up to start the motor once it's warm, and also the motor can shut off at stoplights and proceed onward. So that's what I've been working on.
Apologies for the mumbling
r/CarHacking • u/_WalkTheEarth_ • 18h ago
r/CarHacking • u/ElDucan • 2h ago
Hi everyone! I have a Bosch KTS 540. I’m looking for a free license (cra*k) for ESI[tronic] or a similar free program that works with it and is as up to date as possible. Thanks in advance for any guidance!
r/CarHacking • u/Wooden_Exit_3651 • 8h ago
Hi everyone,
I am setting up an Arduino Nano + MCP2515 controller to run a 2013 Mazda 3 electric power steering pump (BFD1-32-600 / JTEKT 135201239, stamped 578M3423) to power a Toyota steering box in my 1950 Willys. The open-source Arduino sketch I planned on using (BBM4 / shifty35) leaves the pump in standby, so it looks like Mazda changed the CAN wake-up sequence on the 2012–2013 firmware.
Hardware & Wiring Setup (Verified Working):
Pump: 2013 Mazda 3 2.0L MZR (VIN JM1BL1TF0D1836705), 2-connector style:
+13.6V LiFePO4 battery), Thick Black (GND). CAN_H), White (CAN_L), Sky Blue (+12V switched ignition). 8 MHz crystal, 500 kbps, 120Ω J1 termination jumper installed, common ground tied to battery negative). What Is Currently Happening:
+13.6V connected to the heavy 2-pin power connector first, and +12V applied to the Sky Blue wake-up wire, the pump's internal logic powers up, ACKs 500 kbps CAN traffic cleanly, and continuously broadcasts 0x240: PUMP 0x240 -> 00 80 00 00 00 00 00 00 I have tried sending the standard 2010–2011 (BBM4 / shifty35) frames every 10ms:
0x201: {0x1F, 0x40, 0x00, 0x00, 0x27, 0x10, 0x00, 0x00} (2,000 RPM, 0 km/h) 0x082: {0x00, 0x32, 0x00, 0x00, 0x00, 0x00, delta, 0x00} (steering rate delta = 1..16) 0x240 stays latched at 0x80 and the motor remains off (Byte 0 = 0x00). Questions for Anyone Who Has Decoded the 2012–2013 Mazda Pump:
BFD1-32-600 pump require an additional HS-CAN frame (such as 0x420, 0x215, 0x090, or 0x202) or a rolling counter / checksum on 0x082 or 0x201 before it clears 0x80 and enables the motor? 0x240 Byte 1 = 0x80 with 0x201 + 0x082 active indicate a latched internal motor/FET fault on this unit? Any captured startup logs from a 2012–2013 Mazda 3, DBC snippets, or working Arduino examples would be hugely appreciated. Thanks!
r/CarHacking • u/marktimmons • 13h ago
Does anyone have the VX Manager 1.2.x (probably 1.2.0.0905 or similar) drivers executable installer you could share with me?
VXDiag no longer supplies this older version. I have a VXDiag VCX Nano USB version for JLR if that matters. Thank you.