r/Jimny • u/Extra-Lack-9798 • 2h ago
outing JA11 Snow Wheeling
Took the Jimny out for some snowy pics βοΈ π
r/Jimny • u/Extra-Lack-9798 • 2h ago
Took the Jimny out for some snowy pics βοΈ π
r/Jimny • u/the_Medic_91 • 2h ago
r/Jimny • u/Electronic_Ad_3333 • 2h ago
Went to take a photo of this road towards Kibuneguchi station when perfectly a jimny drove into the shot
r/Jimny • u/Sea_Squash6323 • 12h ago
Took the little one out to the desert for the first time today! she did not disappoint ποΈπ
r/Jimny • u/The_Kneecapper • 11h ago
Tony is tinsel-ified and now a jolly Jimny! If I had a bullbar thereβd be ALOT more :D
r/Jimny • u/Redditalan17 • 21h ago
I'm lending my mom my Jimny these days because her car is in the workshop. Today she parked and this beautiful 5P Jimny of the same color parked right next to her. Considering that the parking belongs to the most popular shopping mall in my city (always busy) and it's huge, this person is definitely following the LAW!!
PS: It's not that the person had any other option really. The law is the law π.
r/Jimny • u/ThottinAndPlotting • 4h ago
Has anyone found a short shift kit for Gen4 Jimny? I know the gear throws will ever be as short and tight as a manual Mazda MX5, but would love to improve the feel (without hopefully voiding the warranty π)
r/Jimny • u/ThottinAndPlotting • 5h ago
Hi all. Just purchased a 2026 2 door Jimny. Which reasonably priced, yet rugged floor mats do you recommend? I only need floor mats for the front, since the backseat is such a joke π€£π€£ Should I look Amazon? eBay? I'm in Rutherford NSW Australia
r/Jimny • u/Own_Club_964 • 10h ago
Hello, new Jimny owner here.
Purchased a second hand 2017 jimny. Previous owner said the o2 sensor needed replacing, but some googling makes me believe it might be the catalytic converter.
Anyone had these codes or issues before?
New to cars so any advice would be appreciated if you understand any of these numbers π π
Thanks for your time!
we are looking into 1999 jimny for sale in sweden. 180kkm
is it ok or should run away?
r/Jimny • u/MeteorologyMan • 1d ago
Australian based - About to purchase a 2026 Jimny XL and I'm looking for a few options on a lightweight roof rack with either a wind deflector or one that doesn't vibrate like crazy.
Primarily looking to hold down surfboards/lightweight Kayaks, well aware a rooftop tent is too heavy for the advised limit...
Thanks in advance.
r/Jimny • u/Ok-Jello-2050 • 1d ago
I have an 01 jb23 kei and am striking out everywhere to get a minicon. Anyone have a source or any tricks?
r/Jimny • u/nail_hammer01 • 2d ago
hey, this is my jimny and i have been dizzy over what shock+springs kit to get. i have multiple choices: old man nitro gas, ironman nitro gas, mamba racing adjustable and profender's adjustable shocks.
i looked around for what would suit my needs which are a good ride off-road and more importantly a not extremely stiff ride on-road. my cousin has the ironman its a 2inch lift with the 0-200 medium springs and 235 70 15 at tyres and every time im in his car its annoying how bouncy it is . so when i researching it showed me that old man is a bit softer on the spring rate, with knowing that im not gonna put any more weight other that the camping stuff when i go out and the car being empty nearly all the time, i started learning more towards old man. and im going to put yokohama geolander a/t4 on my car
the rest of the options i have absolutely no idea of anyone talking about them, only profender's but its about them being harsh and needing time to loosen up + it was not on the jimny and they didn't go through that setup for more than 2 weeks.
this is my first post here and i hope its not gonna be my last since i love my car
r/Jimny • u/Winter-Party-3531 • 1d ago
May be a long shot! Anyone on here based around Suffolk/Norfolk, UK with a Suzuki Jimny?
Looking to meet other local owners for a drive/coffee!
r/Jimny • u/narcarsiss • 2d ago
2006 Suzuki Jimny JB43 | M15A Swapped | Haltech Elite 750 | Queensland, Australia
Thought I'd share my little Jimny project.
I bought what was clearly someone's dream build. The previous owner was a younger bloke with some pretty ambitious ideas, a decent collection of aftermarket parts and apparently enough confidence to start modifying just about everything.
Unfortunately, from what I've discovered, the workmanship didn't always match the ambition.
I'm not a mechanic myself. I'm an IT/network engineer. But I'm comfortable with electrical systems, troubleshooting, fault isolation and learning how complicated systems work.
So I figured, how hard could it be?
Famous last words.
What started as fixing a few problems turned into practically dissecting the entire vehicle, tracing wiring, discovering hidden damage, rebuilding systems and trying to turn someone else's unfinished project into something reliable.
The frustrating thing is that underneath all the problems, there's actually a pretty cool Jimny.
The dream is there. It just needs finishing properly.
---
The Mod List β What's Actually in It
Engine, Induction & Internals
- Suzuki M15A 1.5L engine swap
- Upgraded higher-lift camshafts
- M16A intake manifold
- M16A exhaust manifold/extractors
- Extractors wrapped in fibreglass heat-resistant cloth
- Cylinder head flow matching
- Bottom-end bearing upgrades
- Upgraded engine bolts
- Upgraded valve retainers and shims
- Haltech-controlled intake VVT
- Aftermarket pod filter in a custom airbox
- Raised air intake snorkel
- Haltech WB1 wideband oxygen sensor controller
- Professionally tuned engine management
Cooling & Thermal Management
- Upgraded full-alloy radiator
- Haltech-controlled electric thermo fan
- Custom thermo fan relay and power distribution
- Exhaust extractor heat wrapping
- Progressive engine-bay wiring relocation and heat protection
- Additional heat shielding around wiring exposed to exhaust and engine temperatures
I've been progressively cleaning up the engine bay, tucking wiring away properly and protecting everything from unnecessary heat exposure.
With the engine swap and aftermarket management, there's a fair amount of wiring that needs to be routed carefully.
I'm trying to make the engine bay look less like a collection of modifications and more like something that was designed to fit together.
Eventually, I'll also get an automotive air-conditioning specialist to properly insulate the A/C piping and tidy its routing wherever practical.
Drivetrain & 4WD
- Factory 5-speed manual gearbox
- Heavy-duty clutch
- Rebuilt transfer case DC shift motor
- JDM extended breather kit for the front differential, rear differential, gearbox and transfer case
Suspension & Steering
- Upgraded Dobinsons springs
- Upgraded Dobinsons shock absorbers
- Factory live axle arrangement
- Further suspension and steering upgrades under consideration
Brakes
- Rear disc brake conversion, replacing the factory rear drums
ECU & Engine Management
- Haltech Elite 750 standalone ECU
- Haltech HT-140604 Rev 1, 2.6 m Advanced Wiring Loom
- Haltech NSP software
- Full standalone engine management
- Engine sensors, actuators, VVT and primary fuel pump relay wired directly to the Haltech
- Original Suzuki ECU retained for remaining factory functions
Current Haltech output assignments:
- DPO1: Intake VVT cam control
- DPO2: Electric thermo fan
- DPO3: Auxiliary driving lights
- DPO4: Factory tachometer
- DPO5: Primary fuel pump relay control
- DPI1: Factory high-beam signal input
Electrical & Lighting
- Haltech PD16 power distribution setup
- Dedicated Haltech fuse/relay enclosure
- Dual-battery system with voltage-sensitive relay
- Narva auxiliary driving lights
- Narva 68000 lighting relay
- ECU-controlled high-beam activation
- Factory negative-switched headlight integration
- Custom fused accessory power distribution
- Reworked engine-bay and passenger-footwell wiring
- Relocated thermo fan and auxiliary lighting relays
- Re-routed wiring correctly into the engine-bay fusebox
- Repositioned and secured the wiring loom away from the steering column
- Ongoing wiring concealment, securing and thermal protection
Interior & Instrumentation β OEM+
- Factory JB43 instrument cluster retained
- Factory tachometer driven by the Haltech
- Factory Check Engine Light/MIL integrated with the Haltech
- Original dashboard appearance maintained
- Rear seat delete
- Two-seater touring/camping layout
---
The Things I've Found Wrong
The previous owner clearly put money and effort into the car, but some of the workmanship has been concerning.
The biggest warning sign was discovering that the accelerator cable had been damaged and the damage simply hidden.
That made me question what else had been overlooked.
So I started systematically inspecting and pulling apart the vehicle.
Some discoveries so far:
- Missing engine earth strap. An essential engine ground connection wasn't there.
- Knock sensor wiring melted together. Not ideal for an engine running aftermarket management.
- Thermo fan and lighting relays mounted in the splash zone. I've since relocated them into the Haltech fuse/relay enclosure.
- Holes drilled directly into the fusebox to run wiring. Rather than routing cables properly through the intended entry points, the previous owner had simply drilled holes and fed wires through.
- Wiring loom rubbing against the steering column. The loom had been routed close enough to contact the steering column, creating a potential chafing and electrical failure risk.
- Questionable wiring routes, connections and abandoned wiring throughout the car.
- Electrical backfeeding between the aftermarket ECU input and factory headlight circuit, now resolved.
- Various mechanical issues that weren't immediately obvious when I bought it.
What I've Done to Correct the Wiring
Rather than keep patching questionable wiring, I've been going through it systematically.
I've re-routed the wiring properly into the engine-bay fusebox, removing the need for the previous owner's improvised cable routing.
I've also lifted, repositioned and secured the wiring loom so it no longer rubs against the steering column.
That one particularly bothered me. A wiring loom contacting a moving steering component is exactly the sort of thing that can become a much bigger problem later.
I've also been progressively:
- Relocating relays away from water and splash exposure
- Tidying and securing engine-bay wiring
- Improving heat protection near the exhaust
- Removing unnecessary or abandoned wiring
- Tracing factory and aftermarket circuits
- Correcting ECU input and output wiring
- Making the electrical system easier to maintain and troubleshoot
My approach has become pretty simple:
Trace it. Understand it. Test it. Fix it. Document it.
Basically what I'd do with a troublesome network, except this one has oil leaks, moving mechanical parts and occasionally tries to shake itself apart.
---
The Mechanical Issues I'm Currently Worried About
Unfortunately, it's got the infamous death wobble.
The vehicle has upgraded Dobinsons springs and shocks, but that doesn't necessarily mean the steering and suspension are in good condition.
I'm planning to take it to a local 4WD suspension specialist in Queensland for a proper inspection.
I'd like them to assess the kingpin bearings, wheel bearings, bushes, steering components, suspension geometry, axle alignment and anything else that could be contributing.
Depending on what they find, I'll look at upgraded components or potentially a differential/axle swap.
This is one area where I don't have the specialist tools or experience, so I'd rather get it professionally assessed.
2. Previously Broken and Welded Rear Shock Mount
This one genuinely concerns me.
The right-hand rear shock absorber mount on the differential/axle housing has previously broken off and been welded back into position.
The repair isn't perfectly straight.
It's close, but visibly not quite aligned.
I don't know exactly how it originally broke, who repaired it or whether the repair was properly assessed afterwards.
Given the forces going through a shock absorber mount, I'm not comfortable assuming it's fine just because it's currently attached.
I'd like the suspension specialist to inspect the weld, mounting geometry, surrounding axle housing and shock alignment.
If it needs to be cut off and properly repositioned or replaced, that's something I'd rather have done correctly than risk another failure.
3. Slight Lean Towards the Left
I've also noticed the Jimny appears to sit slightly lower on the left-hand side.
It's subtle, and I haven't confirmed whether it's actually a suspension issue.
It could be something as simple as uneven tyre pressures or the surface it's parked on.
But given the history of the rear shock mount and the existing death wobble, I'd like to check the ride heights, spring seating, suspension bushes and axle positioning rather than just assume everything is fine.
4. Small Gearbox Oil Weep
There's a very small oil weep around what appears to be the rear gearbox output seal, where the driveline connects.
It's not pouring oil out, but there's enough moisture to notice.
I'm planning to confirm the exact source, then check the relevant seal, flange/yoke condition, driveline play and oil level.
Not necessarily a major problem, but definitely something I want addressed before relying on the vehicle for longer trips.
5. The 4WD System Constantly Flashes
The 4WD indicator constantly flashes, although I can hear a relay clicking in the footwell when operating the system.
Something is responding electrically, but the system doesn't appear to be completing or confirming its operation properly.
I still need to investigate the transfer case actuator, position feedback, wiring and associated 4WD controls.
6. Mystery Jackshaft Rattle
There's also an intermittent metallic rattling sound that appears to be coming from the jackshaft area.
I haven't isolated it yet.
Another one for the mechanical inspection list before any serious touring.
---
Electrical & Reliability Work Still Underway
The electrical system has already taken a fair bit of my time, and there's still more to do.
- Investigate main battery discharge/parasitic drain
- Diagnose slow passenger-side electric window
- Finalise thermo fan configuration and possible after-run
- Finish engine-bay wiring tuck and heat protection
- Secure and protect wiring around the exhaust and cooling system
- Have an A/C specialist insulate and tidy the air-conditioning piping
- Finish wiring tidy-up in the passenger footwell
- Remove abandoned aftermarket wiring
- Complete fuel system and engine-start checks
- Verify factory instrumentation and warning lights
- Finish rear work/reversing lighting
- Complete extended breather plumbing
- Inspect remaining previous-owner modifications
I've deliberately postponed starting the engine again until the outstanding checks are completed.
---
What I Eventually Want It to Become
I'm not trying to build the world's most extreme rock crawler.
I'd like a reliable, capable little touring and camping Jimny that retains its original character.
The eventual goal is:
- A properly sorted M15A engine
- Reliable standalone engine management
- Clean, documented and heat-protected electrical systems
- A tidy, serviceable engine bay
- A fully functioning 4WD system
- Correctly aligned and reliable suspension
- Steering that doesn't try to shake me off the road
- Properly repaired axle and shock mounting points
- Good brakes
- Reliable cooling with the upgraded alloy radiator
- Properly routed and insulated A/C plumbing
- Practical auxiliary lighting
- Soundproofing, vibration damping and heat shielding
- A simple, comfortable two-seat camping setup
- Sensible mechanical upgrades that improve reliability
Some of the expensive parts are already there.
Some need repairing.
Some probably need replacing entirely.
But I can see what this thing could become.
---
I'm an IT Engineer, Not a 4WD Mechanic
That's probably the biggest thing I want to be upfront about.
I'm confident with electrical diagnostics, wiring diagrams, ECUs, troubleshooting and learning new systems.
But I also know where my experience ends.
Suspension geometry, axle rebuilding, structural welding and certain drivetrain jobs aren't things I'm going to pretend I'm an expert at.
I'm happy to research, learn and tackle jobs within my abilities.
But I'm equally happy to pay someone with the right skills and equipment when the job calls for it.
There's a difference between being confident you can learn something and assuming you already know everything.
And this little Jimny has certainly been teaching me plenty.
---
Any Queensland Jimny or 4WD People Around?
One of the main reasons I'm posting is that I'd genuinely like to meet some local 4WD people.
I don't come from the 4WD community. My background is IT and engineering, so this has been a pretty steep learning curve.
It would be great to make a few mates who know their way around Jimnys, fabrication or just 4WDs in general.
I'm not looking for free labour or expecting anyone to fix my car.
I'd like to learn, share knowledge, get advice, lend a hand where I can and eventually get out on some tracks with people who know what they're doing.
The previous owner had a dream for this Jimny. The execution wasn't always great, but the potential is absolutely there.
Now I'm trying to give it the build quality and reliability it deserves.
It's been frustrating, time-consuming and occasionally makes me question my life choices.
But I still love the little bastard.
Any other M15A-swapped Jimny owners?
I'd particularly love to hear from anyone who's dealt with death wobble, rear axle shock mount repairs, Dobinsons suspension setups or similar Jimny builds.
r/Jimny • u/Crazy_Association570 • 3d ago
Well, about 95%
A few more little things to add, but itβs finally looking like a complete car.
- Offroad Animal bar
- Tough Dog 40mm lift
- Ultra LED spots
- Degraaf full stainless exhaust
- A-Line Indus rims with 215/75/15 Radar Renegade tyres
r/Jimny • u/MarshToyokan • 3d ago
I purchased the new Bridgestone IcePeak winter tyres!
r/Jimny • u/JBsupercool • 2d ago
I am attempting to do the alignment of Jimny myself. It's a two year old stock 5 door Jimny.
To give some background, during my second service, the service center guy pushed me to do a wheel alignment telling that it's a part of the second service. I agreed assuming that otherwise it might void the warranty. Then, they took it inside the garage. After that I don't know what exactly they have done, because the customers are not allowed inside the bay. All I can see from the entrance is the car lifted on a lift at the end of the garage and a few guys discussing each other and trying some thing. Eventually, it took around two hours to complete it. Then I took it for a test drive, where everything looked OK except the steering was lightly off center (NOT pulling to the sides). They took it inside once again, did some thing. After that the steering was properly centered.
Everything was fine until the next 4000km or so, I noticed the outer edge of the passenger side front wheel started wearing off heavily. The front wheels were also pointing outwards. It was clearly visible when the car is parked with the steering straight. So I take it back to the service center. They take it inside. This time it took only 30 minute or so. The steering was also centered properly. They told that the problem was too much toe out.
Now after 5000km, the passenger side tyre outer edge shows considerable wear, though not as bad as before. (No steering pull to the sides)
I don't want to take it to the service center again. So I am trying to do a wheel alignment myself.
Could someone else here give me the exact steps to do it, so that the steering angle sensor settings are not messed up. I don't have the software or OBD scanner for doing a sensor reset, and I don't want to as much as possible.
I have gone through the explanations in bigjimny and teamghettoracing regarding the alignment. But I am confused as to how to start. It tells you have to make sure the steering wheel is centered before you do the alignment.
But my question is: even if you center the steering wheel, when you turn the toe rod to make the alignment correct, the steering position will also get out of center, right? Or, is that OK and once you make the alignment correct, you adjust the drag link and center the steering? In that case, will the factory center marking position will change?
# Note: When I checked the steering box, there is no marking/painting which shows the center of the steering. No, it's not peeled off as it looks fairly new and I have never taken the car to off-road.
Also, is it required to disconnect the battery before alignment?
r/Jimny • u/Either-Ad350 • 2d ago
Had my jimny for almost a year now and driven it mostly on sand, I'm going on a trip to the mountains next month and will likely find ice and snow along with steep inclines and tight turns...
I did some practice on the wet mud yesterday and slided it a little and it seems tame at slow speeds even tough you can definitely feel it's top heavy when you go a bit faster.
The car will be loaded with 4 men plus some luggage a tools so I'm definitely worried about the possibility of loosing traction on ice inclines too.
Other than taking it slow is there anything I should know beforehand?
r/Jimny • u/Pretend_Village7627 • 3d ago
Scanned and printed custom dash for my 43.
Also some custom speaker pods. Good to finally tick this off my list of half finished projects.