r/MechanicAdvice • • 17h ago

What is the Nut Splitter nut for?

Post image
288 Upvotes

I bought a set of nut splitters today.

And they came with a nut…

What is the nut for?


r/MechanicAdvice • • 12h ago

Can this be repaired?

Thumbnail
gallery
86 Upvotes

Hi I noticed this missing chunk of metal under my 1999 chevy silverado ck 1500, is there a way to repair this? Is this dangerous to ignore? I assume it is because debre and water can ruin the gears and components.

PS - im trying to address the oily mess too, my other post may be the cause, i am not sure yet.


r/MechanicAdvice • • 21h ago

Why does the serpentine belt keep slipping off?

163 Upvotes

Changed the serpentine belt on my Audi A4 (2012) as the old one was ripped and fell off. But I noticed no matter how I position the new one, after turning off the engine it seems to slack off.

Is this an issue with the tensioner? I’ll post a photo in the comments


r/MechanicAdvice • • 1h ago

What do I do 🫠

2 Upvotes

So I bought a Kia.. Im aware that was my first mistake. Its a 2023 kia sportage xpro prestige & quiet honestly I love the car. It has 55k miles on it my warranty runs out at 60k. I just had the engine light come on for a P0301 code that is going to the shop tuesday to fix. About 3 months ago I had an engine code P2181 that got fixed under warranty they replced the thermostat. My question is with both of these codes happening with low mileage should I just trade the car in before it is out of warranty? Or could these be just random issues. I am upside down on my loan so I would have to put down a significant down payment and honestly there isnt a car I like as much as mine. Even the new sportages arent the same.


r/MechanicAdvice • • 2h ago

Top strut mounts worn?

Thumbnail
gallery
2 Upvotes

2007 Honda Jazz (Fit)

Thunking noise, on extreme sharp turns, going into a steep driveway on am angle. Or slight elevation changes on one wheel.

Comes from both driver and passenger sides of the car, never at the same time however. Left side more than right. Not felt in the steering wheel. The noise is occasional ams does not happen when going over bumps on the road

12/6 and 9/3 test past with no noticeable play on both front wheels. Ball joints on the steering knuckle also have no play

Front shocks have been done previously about 100 thousand kilometers ago.

Noticed a tear on the top. Is this detrimental? No noticeable noise when steering.

I'm waiting on parts to do the control arms, sway bar bushings (what I think is causing the noise) and inner tie rods, wondering if I'll need to do the top mounts also or are these just the dust covers? If so is that a strut out job?

Thank you


r/MechanicAdvice • • 5h ago

Head gasket, or cylinder failure

Thumbnail
gallery
3 Upvotes

Hi, so my good old volvo had some leak of combustion gases into coolant, and it was needing a top up almost everyday. It was time to remove cylinder head, but I am not sure how to fix it now.

After taking off cylinder head i noticed discoloration of gasket on cylinder 4 in direction of cylinder 3. All other cylinders had yellowish color where cylinder sleeve touched gasket, and it was gone there.

On cylinder sleeve there was a carbon buildup there and after lots of cleaning there, there is very small scratch. Cannot put my fingernail on it, but zoomed in I can see it.

Overall cylinder 4 was very clean in comparison to others.

Is just new gasket going to do it for now, or this hair scratch needs tending?

Volvo xc70 2001 2.4t


r/MechanicAdvice • • 5m ago

Not sure if the turbo is going (Peugeot 3008, 2014 1.6 engine)

1 Upvotes

My car has had a lot of bother this year, she is a Peugeot 3007, 2014 with a 1.6 engine. The head gasket went and soon after being fixed the injector clamp went.

I also have a sort of metallic tinkling sound, I went to the mechanic three times over the same sound. It started after I had work done after my MOT. The first time they said they found a sound and fixed it but while doing that something else was loose and I had a new sound. The original sound I brought the car in for remained and was not fixed. I took it back to get the new sound sorted and then waited until I was paid before taking it back a third time over the same sound.

They have said they then the sound is the turbo. It occurs when I'm accelerating, usually when you hit 30 miles per hour and above and they said I might need a new car rather than fix it as it would mean a future with lots of oil issues apparently.

I'm currently saving for a new car as I've obviously spent my savings on fixing the car this year but now when I drive and stop the fan is very loud (similar to what happened before the head gasket went) and I am worried I'm about to have a repeat.

I've included a video of the ratling sound. It's loud when driving but surprisingly hard to capture on video. It's best heard around a corner, when accelerating etc.

I'm looking to get a second opinion on the rattle as a new car is a big expense but I'm now also quite worried about the fan.


r/MechanicAdvice • • 12m ago

is this sound normal?

1 Upvotes

2015 vw jetta


r/MechanicAdvice • • 15m ago

Nissan pathfinder r51 2.5dci 2008 cutting out .

Thumbnail reddit.com
1 Upvotes

r/MechanicAdvice • • 21m ago

2019 Honda civic sport (auto, 18,000 miles) strange noise coming from back, help!!

0 Upvotes

2019 Honda civic sport trim (around 18,000 miles), the noise comes from the back of the car and started after hitting some semi flat pothole/manhole covers. Which parts are wrong/broken please help me!!! Just a broke college student that doesn’t want to end up in the side of the road :( in the video I was driving local speed 20-25 mph (noise has not gone away it’s constant now)


r/MechanicAdvice • • 34m ago

Not been using my car much - battery dead or another issue?

1 Upvotes

About a year ago I changed job so not been commuting in my car anymore. About 6 months after stopping my car wouldn’t start and needed a jump - I then drove it for a bit then it lasted another few months. Now it seems to last less and less time - I took the battery out to charge it on a charger too which helped initially but then after sitting for a couple weeks it was dead again. Have I damaged the battery by letting it get so low that it can’t hold charge anymore? Unsure if I should buy a new one.

Car is a 2010 Skoda Fabia Mk2, 1.4 Petrol.


r/MechanicAdvice • • 34m ago

09 Town Car Cat Bell Ringing Sound

1 Upvotes

My car started doing this rhythmic ringing sound that sounds like a cat bell. I can’t tell if it’s coming from the engine itself or the pulley system. Any pointers would help


r/MechanicAdvice • • 6h ago

Is car engine moving excessively.

3 Upvotes

r/MechanicAdvice • • 1h ago

What can be the reason for this ??

1 Upvotes

My Ritz is 2013 Model. It's meter starts to blink when it's cold in early morning or in the night but this problem doesn't occur in daytime.

What could be the reason for this? How and where can I get it repaired??

I live in Indore and don't know any place.


r/MechanicAdvice • • 20h ago

Mechanic changed my oil but couldn't find a compatible oil filter. Is it safe to leave the car until Monday?

Post image
33 Upvotes

Hi everyone! I have a 2005 Mercedes-Benz A190 and I could really use some advice.

I went to a mechanic today (Saturday) to get my oil changed. However, he drained all the old oil before checking whether he had a compatible oil filter for my car.

After draining the oil, he told me he didn't have the correct filter for my Mercedes. He then put new oil in the engine and asked me to come back on Monday so he could install the new oil filter.

I live only about 2 minutes away from the mechanic, so I’m planning to leave the car parked until Monday and drive it straight back to his shop.

I also noticed that a few drops of oil leaked after the service.

My questions are:

  1. Could leaving the car in this condition until Monday cause any damage to the engine?
  2. Is it safe to drive those 2 minutes to the mechanic on Monday, or should I have the car towed?
  3. Could the few drops of leaking oil indicate a bigger problem?

I'm worried about damaging the engine. Any advice would be greatly appreciated. Thank you!


r/MechanicAdvice • • 1h ago

Boot leak in 2013 ford focus

Thumbnail gallery
1 Upvotes

r/MechanicAdvice • • 5h ago

2013 Audi A7 3.0T — White smoke (smells like burned oil) when warm + misfiring/jerking after engine swap & sitting ~2 years.

2 Upvotes

looking for some direction on my 2013 Audi A7 3.0T (Supercharged) because I’m getting conflicting answers from my mechanic and an exhaust shop, and I’m not sure what to tackle next.

Background & Timeline:
The car sat for nearly 2 years before I had a replacement engine put in.

It still had a full tank of ~2-year-old gas in it. I drove it down toward E, added Lucas fuel treatment/stabilizer, and refilled with fresh 91+ premium gas.

I recently had the center resonator deleted and replaced with a straight pipe connected to the stock mufflers.

Current Symptoms:

  1. White Smoke When Warm (Smells Like Burned Oil): On a cold start, there is no smoke for the first few minutes. Once the engine warms up to operating temperature, white/gray smoke starts coming from behind the engine (driver's side firewall/cat area) AND out of the exhaust tips (also leaving dark/sooty condensation droplets behind the tailpipes).
  2. Jerking / Hesitation / Misfires: When pulling out onto the road or randomly while driving/accelerating, the car stutters, jerks, or feels like it’s misfiring.

I haven't had a post-exhaust-shop tune-up or fresh code scan yet.

My Mechanic: Told me there is oil inside my catalytic converter and to "just drive the smoke out" (and drive the old gas all the way down).

Exhaust Shop: Checked it out and told me the smoke is coming from my engine, not the exhaust system.

Work Already Done on the Replacement Engine:
Engine mounts replacement
Valve cover gasket replacements
PCV / oil separator replacement
Rear main seal replacement
Engine oil filter housing replacement
Intake manifold / supercharger gasket replacement
Spark plug replacement
Thermostat, radiator, coolant tube, and heater pump replacement
Serpentine belt & supercharger belt replacement
Transmission full service (filter & gasket)

My Questions:

  1. Given that the valve cover gaskets, PCV, rear main seal, and spark plugs were already replaced, what could still be causing burned-oil smoke behind the engine and out the tailpipes ONLY once the car warms up? (Could a new valve cover gasket be pinched at the back corner, residual oil burning off the cat, or something internal on the swapped engine like valve stem seals/rings?)
  2. Could the random jerking/misfiring under load be weak ignition coils (since only plugs were replaced) or leftover contamination from the 2-year-old gas/injectors?
  3. Should I stop driving it immediately rather than trying to "drive the smoke out"?

Appreciate any insight from folks who know the A7 3.0T platform!


r/MechanicAdvice • • 1h ago

Peugeot 4007 2010 hdi, issue, no power, key wont turn it over, it does nothing, but wants to bump start, but can't get enough momentum, how to start it

1 Upvotes

r/MechanicAdvice • • 10h ago

2017 Mazda3 2.0L Completely turns on but can't crank.

5 Upvotes

TL:DR Car goes into ignition, all warning dash lights on, and refuses to crank

Important Details:

  • 2017 Mazda 3 2.0L Manual (Japan Made)
  • Blue Driver & Mechanic OB2 Reader both unable to connect to the car while ignition is on (Blue Driver lights up blue but is unable to connect, Mechanic's big ipad reader just fails to connect)
  • All the small and medium size fuses in the engine compartment fuse box were tested for voltage (one terminal on the negative battery and one on the fuse), or continuity and came back fine. As long as I did my diagnosis correctly there, no fuses were blown that would stop the car from cranking.
  • Attempted to jumpstart with another healthy vehicle (Ford F250)
  • Attempted to jumpstart with a battery pack.
  • Using key fob pressed up to push to start button (using both keys)
  • Battery is 1 year old Kirkland, and tested with a multi-meter (read 12.4V)
  • Alternator is original from 2017 (might be the issue, but I don't think it would stop it from cranking on a good battery and with jumpstart)
  • Engine was replaced with a 40,000km used engine from Japan (my car is made in Japan as well) in April 2026 after I broke the first engine (story in another post), so bad wiring could be an issue.

    • A similar situation happened in June 2026 where all the dash lights came on while driving, however I was able to pull over, plug in the BlueDriver and clear all the codes and continue driving until now.
  • Car was Krown coated 4 days ago and the engine bay was sprayed.

Context: I was driving for 50 minutes, when all of the sudden all of my dash lights suddenly came on and stayed on while driving, the speedometer, and revmeter both stopped working as well. The car drove fine for another 15 kilometers before arriving at my destination without issue. After turning my car off (bad idea), I tried to restart it, but then it just went to ignition with all the same warning dash lights still on, and would not crank at all .

I got the car towed home, and when putting it into ignition, the car security dash light flashes very fast for a minute, and then flashes slowly after that for a few more minutes, then stops flashing. (Seen in video)

If you have any insight or need any clarifying questions to help me out please comment and I will respond! Thanks for any help!


r/MechanicAdvice • • 1h ago

2014 Ford Focus 91,200 miles. Automatic transmission with the double clutch. Code p287A.

Thumbnail reddit.com
1 Upvotes

Hello mechanics, please help. I bought this 14 focus cash because it had documented proof of transmission rebuild 25k miles ago. Ran good on test drive. After purchase on the way home it started skipping gears and went i stopped and turned it off wouldn’t crank cause it couldn’t tell it was in reverse. Check engine line come on P287A. I took it to transmission shop and they put Dorman TCM. They test drove it and said it was fine. Nope, after 20 minutes of driving time the same thing happened. Check engine light back but have not checked it at O’Reily’s yet. Been dealing with this over a week and can’t use the vehicle for work as intended. Anything I can do to fix it myself? Not sure if they did a reprogram or relearn. Not sure if it’s the clutch b itself or not. Thanks everyone!


r/MechanicAdvice • • 2h ago

This valve seat is done, right? - Golf R Mk 7.5 EA888 Gen3 2018

Post image
1 Upvotes

r/MechanicAdvice • • 2h ago

Triumph spitfire, starter solenoid clunk

Thumbnail
gallery
1 Upvotes

Issue - 1973 triumph spitfire - Car was running then died, starter & solenoid replaced, just get a clunk when turning key from starter solenoid. no voltage running off the red/white wire from the starter to barrel, (ignition wire?) loose double white wire not connected to a terminal (may have pulled off when taking cover off) Don’t think I can get a voltage reading with the switch disconnected, (runs off the key being turned?)


r/MechanicAdvice • • 15h ago

Did my ball joint fail?

Thumbnail
gallery
10 Upvotes

Hey Mechanics,

So I had my control arms w/ ball joints replaced less than a month ago on the front of my 2011 Honda Pilot Touring, SOHC i-VTEC V6 engine, 170k miles. Today as I was driving home from work, I started to hear a thin metallic scrap/rattle from the front left driver side, consistent with rattling faster when speeding up and slower when slowing down. I got under the car when I got home, and see that there's bits of purple grease around the inside and on the ball joint. I also see that my dust shield is very rusted out, a thin piece was hanging off by the bottom and I twisted it off.

I can't tell if the ball joint failed and shot the grease out, potentially leading to the now scraping metallic noise of the dust shield? What do you guys think? Am I safe to drive this or do I need to call and Uber till I get it into a shop?

Thank you so much in advance for any advice, I am feeling a little defeated after recently paying for the control arms. Attached the best photos as I could. Posting a video below here too

https://imgur.com/a/NWqrbbd


r/MechanicAdvice • • 2h ago

What's this sound at lower rpm while releasing clutch in Mk1 Octavia 1.9 TDI

1 Upvotes