r/Optics • • 10h ago

BBO SPDC alignment: Unexpectedly high singles counts with an off-center 405 nm pump beam, but no confirmed coincidences

Thumbnail
gallery
15 Upvotes

Hi everyone!

I'm an undergraduate physics researcher working with a Thorlabs quantum optics kit to generate 810 nm photon pairs through spontaneous parametric down-conversion (SPDC) using a 405 nm pump laser and BBO crystal.

Today, I encountered something particularly confusing while troubleshooting our optical alignment.

When we follow the recommended alignment procedure and center the 405 nm pump beam, our detector counts typically remain in the hundreds of counts per second, and we haven't been able to establish a convincing coincidence signal.

However, after adjusting mirrors M1 and M2, the pump beam became visibly displaced from its intended path. Instead of passing through the center of the alignment aperture, it appeared to strike near the upper-left edge.

Despite this apparent misalignment, we began observing substantially higher singles counts.

Configuration 1: Beamsplitter installed

The following measurements were recorded simultaneously:

  • Detector A: Approximately 40,000 counts/s.
  • Detector B: Approximately 3,500 counts/s.
  • Detector T: Remained in the hundreds of counts/s.
  • Pump on/off test: Detector B showed sharp decreases in its count rate when we turned off the 405 nm pump.

Configuration 2: Beamsplitter removed

  • Detector A: Increased to approximately 80,000 counts/s.

Removing the beamsplitter approximately doubled Detector A's count rate. However, this does not necessarily establish that the detected light originated from SPDC.

Coincidence measurements: Despite these elevated singles rates, our exploratory T-A/T-B delay scans have not produced a convincing, repeatable coincidence peak.

These count rates are approximate readings recorded during the experiment, as our screenshots do not display numerical y-axis values.

Previous troubleshooting attempts

We've spent considerable time attempting to locate and collect the expected 810 nm photon pairs, including:

  • Centering the 405 nm pump beam using the alignment target and iris.
  • Adjusting the BBO crystal's orientation using its mounting knobs.
  • Aligning the crystal using the reflected alignment laser spot.
  • Repositioning the collection optics and adjusting the detector collection geometry.
  • Rotating and removing the 405 nm half-wave plate between M1 and M2.
  • Following the troubleshooting procedures in the Thorlabs documentation and instructional videos.

Interestingly, some of our more carefully aligned configurations have produced substantially lower count rates than the configuration in which the pump beam is visibly displaced.

My main question is: Why would an apparently misaligned 405 nm pump beam produce significantly higher singles counts than our nominally aligned configuration, without corresponding evidence of photon-pair coincidences?

I'm considering several possible explanations, including scattered pump light, fluorescence, or changes in spatial collection geometry. I'm also unsure why Detector A registers substantially more counts than Detector T when the beamsplitter is installed.

I recognize that high singles rates alone do not demonstrate successful SPDC, particularly without coincidence measurements.

For anyone experienced with SPDC, nonlinear optics, or single-photon detection:

  1. Could the displaced pump beam be introducing additional scattered light or fluorescence into the collection path?
  2. Could our nominal pump alignment be geometrically correct but poorly optimized for phase matching or collection of the down-converted photons?
  3. What would explain the substantial difference between Detectors A and T with the beamsplitter installed?
  4. What diagnostic tests would you prioritize to distinguish genuine 810 nm SPDC photons from optical background?

I've attached photographs showing the unusual pump beam position, the BBO crystal and alignment hardware, the detector singles measurements, and our exploratory coincidence scans.

I'd really appreciate any suggestions or insights. I'm still learning experimental quantum optics, and this has been a particularly interesting troubleshooting challenge!


r/Optics • • 11h ago

Using Transport of Intensity Equation (TIE) + PyTorch for single-camera micro-defect phase retrieval — practical for inline metrology?

0 Upvotes

Working on a computational metrology engine (ShivInterferentia) that reconstructs sub-micron surface height/phase variations on transparent glass and wafers using slight defocus stacks on standard intensity cameras—aiming to reduce reliance on vibration-sensitive physical interferometers.

For optical engineers working in QA/metrology:

Where do traditional phase-retrieval or interferometric setups break down most for you (vibration, speed, calibration drift, cost)?

Looking to test our solver on a few real-world sample stacks from interested teams before locking our v1 SDK specs.


r/Optics • • 11h ago

Optical Technician Job post Physics Bachelors looking for advice

3 Upvotes

decided to take a gap year inbetween my physics BA and further education(MA/Phd) I’m looking to stay in the optics industry so I was planning to work as an optical technician before starting an MA in Optical Engineering/optics ( gpa was no good for phds) looking for some advice and if this sounds like a good plan or if there might be better ones. I have a few years of instrumentation and optics research experience but my grades are just barely above a 3.0.


r/Optics • • 2d ago

Why your infrared “temperature measurement” keeps being off — it’s often the lens, not the sensor

0 Upvotes

A lot of thermal-measurement accuracy complaints get pinned on the detector or calibration, but in my experience the lens is a very common culprit.

The issue: observation lenses ≠ measurement lenses. Observation lenses are optimized for a clear, good-looking image. They typically have no hard constraint on:

- Full-field transmittance uniformity (corners pass less energy → temperature gradient artifacts)
- F-number consistency across the field (effective throughput varies with angle)
- Controlled stray-radiation behavior

For measurement, those matter directly: if the lens transmittance isn’t uniform and the F-number isn’t consistent, the same object at the same temperature reads differently depending on where it sits in the frame. You can calibrate the detector all day and still miss this.

So for a measurement-grade system, you want a lens accepted against specific indicators (transmittance uniformity, F-number consistency, plus the usual thermal/MTF checks) — not just “sharp enough.”

Anyone else debug a “wrong temperature” issue that turned out to be a lens problem rather than a sensor one? I’ll happily share the acceptance criteria I use if it’s useful.


r/Optics • • 2d ago

Zemax vs Code V (and other design tools) in 2026

9 Upvotes

What is everyone's opinions on these in 2026 for lens design?

I've used Zemax before and it is a trusted industry standard but I felt like it was quite buggy at times and annoying to work with.

I've never used Code V but I've seen it demoed and I like the scripting part of it and its tolerancing

I've gotten a offer for a license for code V that was twice the cost of the Zemax license, where the latter comes with a nonseq raytracer as well.

Then of course there is both Optiland and Quadoa.

Interested to hear your thoughts.


r/Optics • • 3d ago

Optical architectures in seaweeds, diatoms, and sea slugs are inspiring the creation of new coatings, pigments, and light-harvesting technologies.

Thumbnail spie.org
12 Upvotes

r/Optics • • 3d ago

Looking for ancient laps

Post image
5 Upvotes

Used in optical lab (eyeglasses) when lenses were made of glass.


r/Optics • • 3d ago

Real-time (video rate) Fourier analysis with PCS (for interest)

0 Upvotes

The linked video illustrates real-time Fourier processing with the PCS programming language at video rates together with the PCS graphics overly commands. All this in just a handful of lines of code. I thought it might be useful to bring to the attention of anyone here teaching Fourier optics. See the video description on YouTube for more details:

https://youtube.com/shorts/T4fNYLXd3kE

PCS (the PARDUS Command Script) is a free and open source cross-platform language which is part of the PARDUS robotics control and laboratory automation system with an emphasis on machine vision cybernetic control. I originally designed it for microscopy but it has turned into something quite general. I will be making more general and longer form videos about it soon on the PUMA microscope YouTube channel. The project is on Codeberg but this Fourier code is brand new so may not be up there at the time of posting. I will update the repository over the coming weeks.

PJT


r/Optics • • 4d ago

If You Could Start Over in Optics, Which Field Would You Choose?

19 Upvotes

I'm currently a college student majoring in Optoelectronic Information Science and Engineering, and it's time for me to choose a specific field in optics. Which one would you recommend? What are your thoughts based on your career experience? Which path do you think has a promising future?


r/Optics • • 4d ago

Intra-Pixel Binary Optical Control Layer (IBOCL): Comprehensive Monograph

Thumbnail
docs.google.com
0 Upvotes

​*"Working on an architectural monograph exploring an Intra-Pixel Binary Optical Control Layer (IBOCL)—looking at optical transfer models, diffraction constraints, dual-nibble logic, and a 24-channel telemetry verification framework. It's written as a formal engineering specification separating established wave-optics equations from open hypotheses. Feedback from optics/hardware folks welcome."*


r/Optics • • 4d ago

Feasibility of Newtonian-Reflector with Adaptive Optics at Home

9 Upvotes

Hi everybody, I've been looking into creating my own telescope as a personal project to work on after graduating (B.S. MechE) college. I was looking into challenging, yet rewarding, systems I could implement. One of those was a equatorial mount with harmonic drives, but I think I'm more interested in something with adaptive optics.

I understand that sodium lasers are illegal, so I'd most likely use an actual star for my reference point. I'd want the diameter of the aperture to be around 14-15 in. and maybe a secondary mirror around maybe 2.5-3 in. Would it be possible for under $600? I probably wouldn't go up to anything past defocus/astigmatism. Also, if anyone has anyone used DFTFringe or alternatives? What were your thoughts on the software you used?

Ideally, I'd be able to see the planets with decent clarity and hopefully other galaxies/stars/whatnot.

I'm pretty new to this, but I'm used to being new to things. Please lmk if anything I've said sounds unreasonable. I've been doing a ton of research into the literature and designs that are similar to what I have in mind. General perusing has told me that all the parts need might actually be in budget (as long as I avoid making a really expensive mount).


r/Optics • • 4d ago

How would you test a passive optical 4×4 matrix multiply in a stack of phase plates?

4 Upvotes

I’ve been thinking about a fixed optical compute module made from a stack of patterned glass layers. The idea is to encode the weights in the phase patterns, feed in a coherent optical signal, and read out the result on the other side. This is a concept at this point.

For a first experiment, I’d try a single 4×4 real matrix, including negative coefficients. I’d encode four inputs in four optical modes, have the stack mix those modes, and measure the four outputs. A camera measures intensity, so I’d use a coherent reference if I wanted to recover signed field amplitudes. I’d leave nonlinear activations to electronics for now.

Would you prototype the phase plates with a spatial light modulator first? What would you measure to tell whether the main error comes from the phase patterns, alignment, or readout? I’m particularly curious whether measuring the four basis inputs and then testing a few superpositions would be a good first check.

I wrote up the broader glass-cube idea and included an illustration here: https://lippi.hu/ai-az-uvegkockaban-en


r/Optics • • 5d ago

IR vs UV and the Sun

4 Upvotes

Hello Knowledgeable People. I am not a knowledgeable person, but I'm interested in the correlation between UV index and irradiance (strength of IR?) from the sun. I am asking as a photographer who wants to film the sun at sunrise with a long 600mm lens. Does a low UV index (will be zero until maybe 8AM, I film at 6:30AM) correlate with low amounts of Infrared Radiation? I don't want to burn my sensor using a big ol' magnifying glass of a lens. I purchased an IR cut/ND1000 filter to hopefully mitigate risk of damage. Thoughts?


r/Optics • • 6d ago

How to evaluate the 'aesthetics' of bokeh and the focus-to-blur transition of a lens using optical design softwares?

Post image
21 Upvotes

I've heard that the main tool for this is the Through-Focus Spot Diagram plot (like the one in the image), but how do you extract this information from it?


r/Optics • • 6d ago

Undergraduate project: measuring laser beam waists using the knife-edge method

33 Upvotes

Hi everyone!

I wanted to share a project I worked on as part of my undergraduate physics studies.

We were interested in measuring the beam waist of two lasers using the knife-edge method. As part of the project, we put together an automated measurement setup using a Thorlabs translation stage, an ESP32, an optical power meter, and some custom electronics.

We tested it with a diode laser and a HeNe laser. Our measured beam waist values were:

  • Diode laser: approximately 9.8 µm
  • HeNe laser: approximately 30.8 µm

I also wrote Python scripts for data acquisition, curve fitting, and beam propagation analysis. I've uploaded the code, experimental data, PCB designs, figures, and our lab report to GitHub.

Repository: https://github.com/turtushig22-blip/thorlabs-esp32-laser-beam-profiler

This was an undergraduate project, so I'm sure there are things that could be improved. I thought I'd share it in case anyone is working on something similar or is interested in the knife-edge measurement technique.

I'd genuinely appreciate any feedback, suggestions, or comments on the measurement approach and analysis.

Thanks for reading!


r/Optics • • 7d ago

Article: Triplet's go! The story of the Triplet lens

Thumbnail
gallery
54 Upvotes

I finally managed to finish yet another lengthy article. This time on a topic, which I wanted to write about for quite some time, since I've always been fascinated by these seemingly simple lenses.

It's called

TRIPLET'S GO!
The Story of the Triplet lens
https://www.simplejoy.at/articles/triplets-go

and is a deep dive into the history of the Taylor-Triplet, its predecessors, derivatives and the overall impact on optical design as a whole. In addition to that I've also tried to capture some of the characteristics of Triplet lenses, created an overview of all the Triplet lens names which I was able to come up with and also show a lot of sample images taken with Triplets I found interesting for a variety of reasons ranging from Agfa, Goerz, Taylor-Hobson, Zeiss, Emil Busch to Dallmeyer, Steinheil, Ernemann and many more.

It was a really vast but highly interesting topic to look into and I was truly surprised to find that quite a bit of the information seems barely documented online. I really hope that I've managed to change that a little bit.

I've included way more lens diagrams and details than anticipated, and since I'm not really knowledgeable in terms of optics, there might still be some errors or inconsistencies in there. If you happen to know more about any of the things mentioned, spot some missing or flawed information, please reach out and let me know! I'm always happy to learn.


r/Optics • • 8d ago

What optical detector/instrumentation front-end are you constantly fighting in your setup?

1 Upvotes

I build low-noise, discrete analog front-ends and electro-optical instruments. I’m investigating common hardware bottlenecks in experimental rigs—specifically where commercial off-the-shelf modules (Thorlabs, SRS, Newport, Femto) hit a wall.

Are you hitting limits with:

  • ​Laser relative intensity noise (RIN) swamping absorption signals?
  • ​Photoreceiver transimpedance amplifier (TIA) noise vs. bandwidth trade-offs?
  • ​Thermal drift in low-frequency/DC optical power measurements?
  • ​Common-mode ground loops between your detectors and data acquisition systems? If you've had to daisy-chain custom op-amp boxes, average data for hours, or discard scans because the detector front-end wasn't quiet or stable enough, what exact measurement were you trying to make?

r/Optics • • 8d ago

A 3D-printed sample stage: 9.77 nm microsteps on paper, micrometre motion in practice

7 Upvotes

A printable linear-axis module for the Arkin optical-tweezers project. A NEMA 11 stepper drives an M3 lead screw through printed 1:1 gears. The carriage runs on steel rods and balls, with elastic-cord preload.

Optical tests of one axis found useful incremental motion of approximately 2.5–4 µm. The calculated 9.77 nm microstep is a command increment, not achieved positioning resolution. The fine-motion tests included a take-up move before each measurement, so the result applies to preloaded motion.

Commanded and measured travel also differ substantially: an 80 µm command produced about 13 µm of movement in the tested setup. Longer moves still need calibration and mechanical improvements.

Disclosure: we're involved in this project through Precisometer. Arkin is funded through NLnet's NGI0 Commons Fund.

Edit: focused the wording on the measurements and direct source files, and clarified the test conditions.


r/Optics • • 8d ago

Open-source optical tweezers on an OpenFlexure microscope: build files and alignment guide

10 Upvotes

An optical-tweezers add-on for the OpenFlexure microscope, using a 1 mW red laser module, a high-NA objective and printed holders and alignment tools.

The photographed build guide covers the bill of materials, assembly and two-point beam alignment. Printable STL parts and editable CAD are available on GitLab; the guide also includes the laser-safety instructions.

The prototype demonstrates lateral trapping. Quantitative force measurements still need calibration. Fast Trap Tracker can record and track bead motion, with stiffness estimates requiring calibrated physical inputs.

Disclosure: we're involved in this project through Precisometer. Arkin is funded through NLnet's NGI0 Commons Fund.

Edit: revised the wording to focus on the technical build and added a direct link to the source files.


r/Optics • • 8d ago

Metasurface waveguides for all-day augmented reality glasses

Thumbnail
nature.com
5 Upvotes

r/Optics • • 8d ago

ISO 10110-7

0 Upvotes

I found an older version of this online: https://cdn.standards.iteh.ai/samples/18093/515e185ee90541409baea98855e76da3/ISO-10110-7-1996.pdf
looks like it has most of the content. Just wanted to check if the 2017 version or even the 2008 version added anything that I should know.


r/Optics • • 8d ago

Progress on the testglasses

Thumbnail
gallery
36 Upvotes

Thanks for the tips on the making of the proofglasses. I am now on to polishing and it is going well so far!

Might share more once they are done or when i move on to manufacturing the actual lenses for the loupe


r/Optics • • 9d ago

13 infrared lens selection mistakes I see over and over (and the checklist I use to avoid them)

11 Upvotes

I work on IR thermal imaging systems and see the same selection errors repeat across projects.
Here’s a distilled checklist that has saved me from expensive rework.

Detector-matching traps

• The lens’s max image-circle is smaller than the detector’s active-area diagonal → vignetting and edge shading with no room to fix it later. Always compute the diagonal from array resolution × pixel size first.

• IR back focal length is not interchangeable with visible-light BFL. Get this wrong and the image plane never lands on the focal plane.

Optical-parameter traps

• Don’t infer range from focal length alone. Real detection/recognition range needs pixel size, IFOV, target radiation and atmosphere.

• Never accept a spec that only lists diagonal FOV — demand HFOV and VFOV separately.

• Watch over-rated F-numbers. Verify with measured throughput and NETD, not the datasheet claim.

Athermalization traps

• Outdoor / vehicle / airborne (–40 to +60 °C) without athermalization WILL defocus with temperature. Indoor constant-temp benches don’t need it — don’t pay for it there.

• Optical athermalization = simplest & most reliable (no electronics). Electromechanical = flexible but adds SWaP, firmware and is vibration-sensitive. Pick by scenario, not by “tech level.”

• The #1 mistake: using an observation lens in a thermal-measurement system. Observation lenses have no constraint on full-field transmittance uniformity or F-number consistency → measurement drift and bad accuracy.

Happy to go deep on any of these — which one has tripped you up the most?


r/Optics • • 10d ago

I have Deuteranomaly - Color Blindness

4 Upvotes

I have 20-20 vision. My question is, can i still pursue Optics study for future career?