r/ProjectHondas • u/ForLape • 11h ago
car pics My 88 Prelude in Australia
galleryWanted to share my build for those interested in learning the story behind it 🙏
r/ProjectHondas • u/ForLape • 11h ago
Wanted to share my build for those interested in learning the story behind it 🙏
r/ProjectHondas • u/cr4pm4n • 10h ago
r/ProjectHondas • u/racesomeday • 1h ago
Proper motorsport corner-weight scales are pretty expensive, so I decided to build my own for a fraction of the price!
The project is based on another guy's DIY scale design. He shared all the instructions, firmware and software for free, so huge thanks to him! You can find the link to his project in the video description.
I made a video showing the build process, the problems I ran into, and finally weighing my Civic EG.
The total cost was around €168 for all four scales!
r/ProjectHondas • u/No-Floor-7722 • 14h ago
Good evening all! I've been on quite a journey trying to solve a particular issue that has become pretty expensive and left me completely clueless.
I have a 1999 Honda CR-V RD1. Recently I've swapped in a USDM EJ cluster, and while it works, unfortunately due to a recent move I've found that I actually need something that works in metric. The issue I'm currently having is even finding either a CDM or JDM cluster that works, so I've just decided to be a bit crazy and make my own. Something I've noticed is that the EJ/EK/RD1/DC2/DC4 clusters all use the Nippon Seiki II New Sabina boards. I've been trying to determine what the jumper pins do to configure the board, since my running theory is that all of these boards use the same IC2 chip but have different slots jumped on the JA-JF connections. I have no way to test this without ruining my known mileage. I've also ordered a CDM cluster but unfortunately, that was destroyed, and it wasn't cheap. The easiest solution I can think of is to reference either a CDM/JDM/EDM daughter board on the back of a speedometer. Fortunately it easily comes off without any permanent damage. If anyone might have an image of said board so I can compare it to mine, or even documentation on the board itself, that would be greatly appreciated, so that I may reconfigure it to move the odometer barrel at the intended rate. I've uploaded pictures I've taken of my board.
r/ProjectHondas • u/MR-BISCUITS7884 • 15h ago
The car ran great until I parked it a few years ago and it sat, now it has a misfire or something. I assumed it was the gas, and I pumped all of the bad gas out and put new 93 in it, and it ran no better. The only other thing I can think of would be injectors or plugs, is there any way to tell which one it is specifically before I just start throwing parts at it? Thanks
r/ProjectHondas • u/Competitive-Top4743 • 19h ago
Finally got her moving under power again! Couple things I gotta work out but first mini me build is alive, moving and almost shifting haha.
r/ProjectHondas • u/Ok-Space-5466 • 1d ago
r/ProjectHondas • u/xostroke- • 22h ago
r/ProjectHondas • u/identihide • 1d ago
Got a valve job and a resurface. For better or for worse, everything but valve springs were reassembled by me. New timing belt, tensioner, and water pump. Refreshed the plastic/rubber of my original injectors. Did timing and valve lash.
I checked the valve lash before first start up, as well as (when cold) after driving and continuing to hear that sound on startup.
It’s significantly quieter when warmed up and I honestly can’t even hear it in the cabin. Car drives better than it did still imo —but I’ve only ever owned the car in its worn out condition.
That all being said, I didn’t reinstall the inner timing belt cover. I just realized way too far into reassembly that I need it before the head or the cams. I don’t know if that’s what that sound is.
No check engine light. All stock / stock-spec. I didn’t touch the block internals at all other than cleaning the top of the pistons.
My suspicion is the tensioner but adjusting it again didn’t change much imo.
Any insight would be appreciated! Thank you in advance.
r/ProjectHondas • u/SpecialAd6301 • 1d ago
Hey all, I've found a set of 15x7 wheels i'm thinking of buying but before I buy them I'd like to ask if the +12.5 offset will cause issues. Thanks.
r/ProjectHondas • u/Ok_Salamander_8505 • 1d ago
r/ProjectHondas • u/sportfit-project • 2d ago
I have a 100% stock 08 orange fit sport and I have absolutely zero car knowledge aside from basic maintenance like oil and tires but I kinda want to start modding my car. Nothing crazy I’m not worried about power atleast rn but I want to make it like a street jdm car ment for spirited drives any tips on what to do where to start and where to look and stuff would be appreciated.
r/ProjectHondas • u/chrisjooo • 3d ago
Hello, I was hoping to get some help figuring out what these wires are, where they go, and if the car needs them or if I can just take them out. I #’ed the pictures for the wires I found together, anything I can do to better help with pictures and etc I will do and any advice and help will be much appreciated. All wires are from under the dash thanks again. It’s a 1996 Honda civic hatchback dx.
Pic1: I found under the steering column
Pic2: I’m not sure what this plug is (maybe alarm?) but the wires run to a relay I believe.
Pic3: I’m also not sure what these wires plug into or where the connector goes.
Pic4: the two red and brown wires were connected before I untied them, one of the wires is grounded (believe it’s the black and red one) but they do connect to the mess in pic #5.
Pic5: also don’t know too much about these wires but some aren’t connected like the blue/red, and black/white, and if anyone can help identify the white wire with a blue connector pls.
Ps, I know it’s a bucket and a headache but I got nothing else to do on this floating rock and learning about this stuff intrigues me (it’s also my new project/baby), so again any advice and help is greatly appreciated. Thank you and again any way I can help with anything just lmk :).
r/ProjectHondas • u/Sh4dowStrik3 • 3d ago
i have a (mostly complete) CARB compliant greddy turbo kit for the B18B
I have:
greddy log turbo manifold
greddy td05h-18G turbo
intercooler piping (one with carb sticker)
hks (sqv i think) blow off valve
greddy blow off valve
turbo elbow
front mount intercooler
manual boost controller
it would still need tuning, downpipe made, and injectors/fuel system
I live in CA but wanted to know what i could realistically sell the kit for as i know they are discontinued
r/ProjectHondas • u/CumCrocodile • 3d ago
The rust under the MC makes me think there might be something wrong with it. Its on my parts car (dc2 gsr), want to use it on my EG (280mm front brake setup with rear disc conversion)
Is it fixable and what could be the cause of the rust? Or maybe its just from spilling brake fluid? I cant test it as I bought this shell with no calipers attached
Cheers
r/ProjectHondas • u/Anonymous_Crankshaft • 3d ago
I have to do a thread repair on my D15B, D/S engine side bracket bosses, I bought a M12x1.75 time sert kit with 24mm, I know that is not the OEM bolt size but last owner did a janky job with a DIY repair, so i have to oversize it, I have enough material to resize, but when i measured the depth again it was ~23.86mm, I am rounding it up to 24mm.
The thing is that Time sert advises an extra 6mm than the insert for proper install, and my question is can i get away with drilling an extra 6mm into the bosses or should just get a shorter insert?
r/ProjectHondas • u/Long-Mud-1783 • 3d ago
I have a 2000 Honda Civic EX with a D16A engine on there I replaced the whole VTEC solenoid and I’m getting good voltage on the VTEC solenoid and the oil pressure for the VTEC i’m getting kind of concerned because I don’t know if it’s ECU related or what’s going on should I bypass it?? where there be any cons to it?
r/ProjectHondas • u/mainaltacount • 4d ago
I have a slight suspicion it's not installed correctly as I need zip ties to prevent the clutch cable from slipping off
r/ProjectHondas • u/EasePuzzleheaded3202 • 4d ago
r/ProjectHondas • u/killacrossova08 • 5d ago
With the car sitting under a cover in my garage, I forget this is a fully functional car. Out of sight, out of mind kind of deal. It felt good to drive her again. So much has changed since I first got her.