r/askanelectrician • • 15m ago

What is wrong?

1 Upvotes

Installing new outlet today and after installing the outlet doesn’t work. The microwave next to this outlet is not working and I can’t reset the breaker? I noticed after I installed if it has red and black wires you’re supposed to cut the middle brass piece? I did not do it before the install… nothing happened when I turned the power on but I tried needle nose pliers on the brass piece to break it off but still nothing. Do I have to call an electrician now, I feel defeated…


r/askanelectrician • • 2h ago

Garage sub panel has a neutral and ground together

Post image
1 Upvotes

r/askanelectrician • • 2h ago

Both of these use non-American style plugs. Would I only need a voltage converter for the 240 amp (and just an adapter for the 120v)?

Post image
1 Upvotes

r/askanelectrician • • 2h ago

How to protect/hide NMb wire with short exposed run

Thumbnail
gallery
1 Upvotes

Hi there, I am completing a renovation in my basement. I have already been helped in this remodel by reviewing the answers you all have given other home owners.

Here is my situation: I removed a drop ceiling and I plan to paint the exposed ceiling black to get some extra height for a gym space. In doing so, I have found this NMB or Rolex wire hanging from the ceiling. It goes down this piece of wood before going through it into the next room where it terminates in an outlet for the basement freezer (picture 3).

My question is, how can I hide this wire to protect it and to match paint with the rest of the wall? I initially was going to use a plastic raceway, but was alerted that they are not usually rated for NMB. I am planning to just get it to the ceiling where it would be tacked to the joist where it is less exposed and could be painted with the rest of the wires.

What options do I have for the wire if I do not want to build a whole little wall which would get in the way of the space I need. Thank you!


r/askanelectrician • • 3h ago

Lost half of my upstairs

Thumbnail reddit.com
1 Upvotes

r/askanelectrician • • 4h ago

Lost half of my upstairs

Thumbnail reddit.com
1 Upvotes

r/askanelectrician • • 4h ago

Lost half of my upstairs

1 Upvotes

I live in a cape cod style house. Replaced a GFCI breaker in the main floor bath. Tested outlet and it's wired correctly. Tested downstream outlet and it is also wired correctly. Installed GFCI back into electrical box. Tested again and still good. 10 seconds later, noticed green light on GFI went out. Checked with circuit tester... no power to outlet. Removed GFI, and have no power coming to outlet or downstream. Kids said the power went out in the upstairs bathroom as well as the power to the ceiling fan in the common area upstairs and stairwell chandelier. I checked the GFI in the upstairs bathroom, and have no power going to that outlet either. Used a multimeter and checked all the breakers in the main panel and have 123 volts leaving all the breakers. Now, I'm lost. Any ideas?


r/askanelectrician • • 5h ago

Outlet help

Thumbnail gallery
1 Upvotes

r/askanelectrician • • 5h ago

Making An Outlet Half Hot

Thumbnail
gallery
1 Upvotes

Hello,

I have an duplex outlet that is pre wired to a switch with only a ground, neutral, hot.

I have seen videos where folks break off the tab on the hot side of the outlet to disrupt the connection between the two screws so that one is hot and one connected to the switch.

I do not have a red wire in the box nor is it in series so not sure how I could do this without running more wire (which is not an option.

the switch has three cables coming into the box, and not sure exactly what's going on with the hot wires.

If it's impossible so be it.

Any advice is appreciated!


r/askanelectrician • • 12h ago

Outlets not working?

2 Upvotes

Recently moved into a new apartment suite Bachelor studio thing and all the outlets work fine but there's 2 separate others that don't. They are the kitchen area ones. I reset the breaker but nothing. I was thinking for a bit that I have to get someone in here over this obviously it's internal but then I remembered that it was BOTH outlets not just 1. Any help?


r/askanelectrician • • 19h ago

Fluorescent to LED conversion

Thumbnail
gallery
2 Upvotes

I picked up a 20-pack of GE LED15ET8G4840 4' LED bulbs a couple of years ago on sale at Lowes. Was planning on converting a bunch of fluorescent lights to LED. Turns out these wouldn't work with the generic fixtures I had, so I shelved it until later. Well later arrived and I started playing with some of the ballast-bypass solutions online. I've tried applying 120v hot to one and both terminals on either end, with neutral to the other, as well as power and neutral to either pin on one end or the other, but no reaction. Tried the same with a 12v 18a Ryobi battery, but nothing. I figured there should at least be some type of resistance across pins, but nothing with any combination tried. I'm seeing some comments that a Type A ballast is needed, but I'm not sure which one. Would appreciate any suggestions as to which process I need to use, and what part is needed if necessary.


r/askanelectrician • • 17h ago

Lights flicker when washer is running

1 Upvotes

Hello!

As the title says, when the washer is running, my kitchen lights flicker.

- The flickering happens only during the agitation part of the cycle.

- You can hear/see that the flickering is in sync with the agitator moving back and forth

- The lights and washer are on different circuits, but they are on the same side of the breaker panel

- The laundry room is adjacent to the kitchen - the cables likely take the same path to the breaker panel (I haven't checked)

- We haven't noticed it with any other lights

- The light fixture probably uses LED bulbs (I'm not 100% sure if I've switched that one to LED yet, but I'm pretty sure I did. I can check, if it matters)

Any advice? It drives my wife nuts!

Thanks!


r/askanelectrician • • 18h ago

AFCI tripping while gaming

Thumbnail reddit.com
1 Upvotes

r/askanelectrician • • 1d ago

How to wire a ceiling fan?

Thumbnail gallery
2 Upvotes

r/askanelectrician • • 21h ago

Installed A/C disconnect, I have a grounding question

1 Upvotes

I installed a disconnect, the previous disconnect was a breaker and it had to be flipped on and of several times in order to get 240v to the contactor. I noticed that the last time I was cleaning the unit and shut off the breaker (at the disconnect) to shut power down to the outside unit.

The new AC disconnect install went smooth for the most part, the only issue I had was the 1/2 knockout in the bottom right as you can see in the pic. I had to run to the store to get a 1" to 1/2" reducing washer.

https://i.imgur.com/kbkzA9S.jpeg

When I completed connecting the wires, I turned the breaker on at the panel. 120v from L1 to ground (used the threaded mc connector for ground), 120v from L2 to ground (used the threaded mc connector for ground) and 240v when touching L1 and L2.

When testing for voltage, I also tried L1 to the box, I did not get 120v. I am almost certain I also tried L1 to the green ground screw and I did get 120v. Is the box being painted the reason I didn't get 120v during my testing? Same with L2 to the ground screw, I am almost certain I got 120v there, as well.

Normally when I'm testing from hot to the box/conduit (In Illinois many circuits are full conduit and dedicated ground wires were not ran back in the day, but I believe many electricians are now including grounds in conduit in case of conduit break, also, it might be code (now), not 100% sure on the code part.

Do I need to revisit this and make sure I get 120v when I touch L1 or L2 with one lead and the other lead on the box? I want to make sure the box is grounded.

I will go back to confirm that I get 120v from L1 to the green screw since I am not second guessing myself.

Thanks.

Update

I went back to test some more, I think the paint on the metal case is the issue.

Here is everything I tested

  • L1 to L2 = 240v
  • L1 to ground block = 120v
  • L2 to ground block = 120v
  • L1 to reducing washer = 120v
  • L2 to reducing washer = 120v
  • L1 to mc threads = 120v
  • L2 to mc threads = 120v
  • L1 to the notch on bottom of case = 120v
  • L2 to the notch on bottom of case = 120v
  • L1 to case = 0v
  • L2 to case = 0v

The notch is where the plastic cover fits in to which covers all the wires.

I think if I buy the 1/2 ground bushing it isn't going to do anything because the case paint is still not going to give me a good reading.

For these two tests, the only thing touching the metal box is the screw that holds the block down which means the screw is getting its ground from the box, the part that is not painted. The fact that I'm getting 120v reading confirms to me that the ground on the metal case is good.

  • L1 to ground block = 120v
  • L2 to ground block = 120v

Does this install like fine as is or am I missing something here?

Thanks.


r/askanelectrician • • 1d ago

Question concerning wiring a shed in quebec

Thumbnail reddit.com
1 Upvotes

r/askanelectrician • • 1d ago

How do I adapt a 3 wire air compressor to 4 wire outlet?

Post image
1 Upvotes

I have an old reliable 220V Coleman air compressor that I want to wire into my new house. I’m hoping to use my existing clothes dryer outlet (temporarily) until I get an electrician to add an outlet to my garage.

The air compressor only has 3 wires, Black/White to the switch, green to compressor body.

The dryer outlet is 4 wires, red/black, white, green to body of dryer.

Can I buy a 4 wire dryer cord and use that on the compressor? What’s the orientation of wiring?

Pictured is the switch housing on the compressor. Power comes in from the right side of the photo.


r/askanelectrician • • 1d ago

Dimmer switch acting weird

1 Upvotes

I installed a 3 way dimmer switch these in a 3 switch circuit, replacing a traditional switch. It controls a pendant fixture with 6 LED dimmable 35 watt bulbs.

Most of the time it works fine, switch turns the lights on and off, the slider adjusts the brightness, just as expected. The other two (normal) switches also work fine.

Sometimes, however, it acts weird. The brightest setting is in the middle of the slider range, it goes from no light to bright and then to dim. Sometimes, the lights take a second or two to light up. And then it goes back to normal.

Ideas?


r/askanelectrician • • 1d ago

Thoughts on This

Post image
1 Upvotes

The switch on the left switches overhead lights and one outlet. I need the outlet to be always hot, not switched. The black wire going into the yellow nut from the right conduit is hot, the others are not.


r/askanelectrician • • 1d ago

Do I need to move/remove this outlet?

Post image
2 Upvotes

We are installing a gas fireplace on a blank wall. The contractor has built out the rough-in. There is an outlet right in the middle of the rough-in. Obviously we need power for the fireplace, and will be running it for the TV above. Can I just tap off this box (removing the duplex outlet) and run from there, or will I need to fully remove any junction (then junction in the basement) and run new power up through the rough-in?

EDIT: The gas fireplace will be permenantly installed into the opening.


r/askanelectrician • • 1d ago

Fan replacement install, breaker tripping

Thumbnail gallery
2 Upvotes

Looking for help replacing a fan at my father-in-law’s place when I hook up the whites coming into the box and to the fan and the blacks coming into the box to the fan, the breaker keeps tripping.

When the breaker isn’t tripped but the switch is off. The longer black and longer white are hot. When I turn the switch to the fan on the only wire that is hot is the short black wire.


r/askanelectrician • • 1d ago

How would you replace a old lighting junction box with 5 cables?

Thumbnail gallery
1 Upvotes