r/diyelectronics • • 6h ago

Question How do you safely extract the lipo battery?

Post image
10 Upvotes

Picture not mine although I plan to open my own bluetooth headphones soon. I’m a beginner at anything electronics.

Do I just snip off the wires coming from the battery one by one while taping the ends with lots of duct tape to prevent shorting?


r/diyelectronics • • 16h ago

Question Alternatives to hard gold for an edge connector?

Post image
33 Upvotes

I'm tinkering around with a Sony minidisc remote protocol, and for that I've whipped up a tiny PCB to break out the connections. I had it produced in HASL lead free, but even with a few insertions its getting very tarnished and dented and such. I know the ideal would be hard gold, but even on such a tiny board that immediately shoots the price up to hundreds of dollars, instead of $10 for 5 of them. Is there something else I can do as a slightly more durable edge treatment, or some kind of harder component I can just solder on top of the pins? the pins are 1mm x 3mm, but I've only got between 0.2mm and 0.4mm to work with as extra space.

Should I just throw a fresh layer of solder over it every once in a while and call it good? Is there a more elegant solution that I'm missing?

Thanks ❤


r/diyelectronics • • 43m ago

Project HDMI Ambient Backlight 4k60

Post image
1 Upvotes

Another project that's been on my list for years. I know it's been done a bunch of times but I wanted to take a shot at my own version of an HDMI ambient light controller. With the price of Raspberry Pis these days, I didn't want to waste a whole Pi or wait for it to boot and run Linux.

The board uses a GSV2001 splitter, MS2130 capture card, ESP32-S31 controller so its all-in-one. HDMI in one side, HDMI and LEDs out the other. It's got a web interface with lots of controls.

Note that Fable 5.2 did basically all the work here with little prompting. It built firmware for those obscure chips, picked parts and designed the PCB, and did all the board bring-up. I ordered the PCBs mostly assembled from JLC without really looking at the design, and I'm super impressed that it works! This was mostly a test since they announced new models can do electronics and I had my doubts - turns out it does a really decent job. Looking at the PCB now, there are many routing decisions I'd change, but overall it has HDMI and USB lines on board and they all worked.

https://www.reddit.com/r/electronics/comments/uqv98g/electronic_catan_lcd_tiles/


r/diyelectronics • • 15h ago

Project Using an Ultrasonic HC-SR04 distance sensor without a microcontroller.

Post image
13 Upvotes

This was a curiosity project to see if it's possible to use the ubiquitous ultrasonic sensor without a microcontroller.

The 555 timer generates a pulse to the trigger pin of the sensor, and output from the sensor's echo pin is fed through an RC filter into an LM393 comparator with that output driving a motor with a simple BJT transistor.

Annoyingly it's not possible to upload a video; but this circuit uses the motor to pull an object towards the sensor before it reaches a pre-determined threshold and tells the motor to stop.

Full circuit diagram and video is available here


r/diyelectronics • • 19h ago

Question What are these silver things?

Post image
25 Upvotes

Never seen them before. To clarify im asking about the cylindrical components marked j1500, 2200, 3300.


r/diyelectronics • • 22h ago

Project Chasing down watchdog resets

Post image
23 Upvotes

The latest l0destar board tracks so fast that gaps in the telemetry are more noticeable and shouldn't ever happen because it's also now backed by a flash buffer. I'm currently chasing down an annoying issue where the system sometimes freezes completely in areas with weak signal and triggers a watchdog reset, resulting in a gap of 30-60s. Managed to reproduce it once on the bench with tin foil around the antenna to simulate a bad cell. Took 25mins though and I'm 30min into a second run without seeing the same thing.

Currently unknown if its a firmware issue or hardware, one theory is with the flash added the 3.3V rail might now be near its current limit and high-power sends could be marginally browning out. This is why I've got the scope on the rails set to trigger on drops below the minimum voltage the SIP needs. Non-volatile memory survives the reset though so not sure how plausible this is.

https://l0destar.com


r/diyelectronics • • 7h ago

Tools Looking for neat gozmos / tools

Thumbnail reddit.com
1 Upvotes

r/diyelectronics • • 9h ago

Question Remote Controlled Variable Resistor To Manage Fan Speed?

1 Upvotes

I have a pedestal fan which I can turn on and off remotely with a wifi-controlled switch.
What I can't do is change the fan speed because it's got an old-school mechanical rotary switch.
The brand does have remote controlled fans but not in the size I need. They also have DC fans with unlimited speed adjustment, as compared to their AC fans which have 3-4 preset speeds. Again, not in the fan size I need.

I was thinking I could add a wifi-controlled variable resistor into the circuit after the wifi switch and before the fan's inbuilt switch.
In theory I could leave the fan's controls set to maximum then manage the power & speed via the app for the wifi switch & resistor.

Would this work?
If so, how would I make a wifi-controlled variable resistor?

Edit - I've seen PWM mentioned a lot in the context of lights. Would that also work here?


r/diyelectronics • • 17h ago

Tools IC removal breadboard/socket

4 Upvotes

Does anyone have a nifty tool/methode for getting IC's out of a socket or breadboard? Now I'm seesawing them out with a screwdriver or by hand, but there's got to be a more conveniant way. Thank you in advance.


r/diyelectronics • • 1d ago

Project Mini digger conversion

Post image
8 Upvotes

Hi, I have a project in mind best represented by this image. How could I convert an existing fuel powered mini digger to an electric (mains power). Is this feasible? I would then want to limit its functionality (like in the image, cat tracks deactivated) and limited turning radius. Any ideas or if this isn't the right place any other subs that might be able to help?


r/diyelectronics • • 1d ago

Project Looking for advice for basic parts list - Audio localisation

2 Upvotes

Hello kind friends, im putting together a parts list for a project coming up , involving the localization,

my needs are : 192 k hz sampling rate at a minimum,

and a minimum of 4 channel input for the ADC , ( 4 microphones)

what i have put together is :

Behringer UMC404HD and 3 Superlux ECM999 microphones.

https://www.thomann.de/be/behringer_umc404hd.htm

https://www.muziker.si/superlux-ecm999

These are great and made to work together , but come in a bit pricey,

id prefer to use simpler Mems microphones, but looking for a pre built ADC for such frequency and 4 channel input , comes in at about 2x the price of the Behringer , making me question if its worth it.

The only option i know of is to build a custom pcb ,but thats not really what i want to do in this testing phase,

any advice welcome , this isnt really my field of engineering.


r/diyelectronics • • 23h ago

Project I wrote a free 8-lesson Arduino course for ages 11-14 that runs in Tinkercad, so kids don't need kits

Thumbnail reddit.com
1 Upvotes

r/diyelectronics • • 1d ago

Parts I need help with battery pack for portable air compressor

1 Upvotes

so bought those pos portable air compressors.

I could hardly inflate a tire from flat to 28psi before it dying. it just barely got me to a gas station.

would like to upgrade the battery pack on this to have it last

says VC18650 2000mah (BS!!) 7.4V 14.8wh

looks like this https://postimg.cc/gallery/YwdRCwp

it also has some plate on the back bridging the 2 batteries?


r/diyelectronics • • 1d ago

Question How do I (safely) remove this stripped screw?

Post image
5 Upvotes

I'm utterly unable to remove this stripped screw. I need help.

I ve even bought and tested a magnetic screwdriver set, to no avail.

I also tried all the basic or cheap tricks:

  1. Use the proper size screwdriver (00) -> still "clicks", but the screw was so tightly screwed, that it stripped anyway...
  2. Use a flat screw, or a star screw, a screw a degree above... -> nope! Bought a full magnetized set *just* for this one screwdriver, to no avail.
  3. Use a screw extraction drill -> I can't afford a drill right now, and it will stay that way for months.
  4. Use a rubber band -> did not work
  5. Use baking soda + superglue -> sounds unsafe as hell. How do i even protect the ssd from the heat and spillage?

The fifth one sounds like a disaster waiting to happen. I'm stuck. Any ideas here on how to deal with it?


r/diyelectronics • • 1d ago

Project Realised I can build test versions of my boards for current measurement

Post image
12 Upvotes

Every current path is broken out to a jumper so I can use a Nordic PPK2 to measure current and find out exactly where all the sleep current is going. It's only about 35uA but I'm obsessive!


r/diyelectronics • • 2d ago

Project Mesh network in ZYN packages

Post image
84 Upvotes

I found some parts I bought years ago and was bored the last few evenings, so I put them into ZYN packages.

It's an Arduino Nano, nRF24 modules, a temperature sensor, a vibration motor and a DIY touch button in the lid. Not sure what I'm going to do with it, but I might make a custom PCB with LiPo battery and charger for it and assemble one every time I finish a package.


r/diyelectronics • • 1d ago

Question How to make my own wear OS based smartwatch?

0 Upvotes

I do have an old watch shell (i.e. internals are empty), but I can't find a microprocessor small enough to actually fit inside it. And an lcd too.

If I'm sure, the diameter of my watch is 42mm.

Can anyone guide me how to build a smartwatch on my own? I'm genuinely excited for this project.

Thanks.

Edit- the watch shell is a Casio MTP 1314.

Edit 2- bruh


r/diyelectronics • • 1d ago

Question What do I need to make my custom mp3 player?

0 Upvotes

I'd assume I need a raspberry pie first, a screen, something with bluetooth and wifi so I can actually download spotify, sd card reader and also a port so I can use my wired earphone. Now here is the thing idk what model of components to use. Kindly suggest me some cheap modules so I don't face any compatibility issues. Also please let me know if I missed something. Thank you.


r/diyelectronics • • 1d ago

Question Newbie looking for assistance with supply list for automatic light

2 Upvotes

I just recently purchased Practical Electronics for Inventors and have really enjoyed just reading through it.

With that said, I've been a nurse for a decade and don't have any actual hands on experience with building electronics but have always been interested in learning.

I wanted to try my hand at a very simple project: a light that turns on automatically when I open my pantry door.

I imagine it will be battery powered and use a reed switch. Beyond that though, i have no idea what to get! I imagine it will use a small LED light. I also already have a soldering iron, for whatever that's worth.

If anyone could help me come up with a list of supplies to buy, that would be great! I will attempt to figure out the rest on my own and pop over to r/askelectronics when i get stumped. It's hard to just read about electronics without something physical to practice on.


r/diyelectronics • • 2d ago

Question I can’t find anything about this in the internet: Caterpillar : L4981 MA1-006M MCAT3 1147 T13 e1. Thank you

Post image
43 Upvotes

r/diyelectronics • • 1d ago

Need Ideas How do I power this string of parallel LEDs ?

Post image
4 Upvotes

I am repairing/renovating a small Christmas tree lighting string built into a larger Christmas mountain display. There is a string of 8 tiny LED's wired in parallel, terminating in two wires. I applied a test 3v and lit LEDs numbers 1,3,5,7 Then applied the 3v but reversed the polarity to make LED's 2,4,6,8 light up. So it needs some sort of switching IC or circuit?

The original PCB is toast, so can anyone help provide an answer on how to power the circuit? TKS.


r/diyelectronics • • 1d ago

Question Need recommendation on beginner kit

Thumbnail reddit.com
3 Upvotes

r/diyelectronics • • 2d ago

Project A Marx generator I made

Post image
9 Upvotes

Just wanted to share this. Works like a charm but I couldn't get a photo of it firing.