r/AskElectronics • u/Lucgamer • 15h ago
Which one of those pins is Pin 1 on a STM32H503?
There are two dots, I'm assuming that the little one indicates pin 1. But I'm not sure. Can someone confirm if that's indeed pin 1 or not, please?
r/AskElectronics • u/Lucgamer • 15h ago
There are two dots, I'm assuming that the little one indicates pin 1. But I'm not sure. Can someone confirm if that's indeed pin 1 or not, please?
r/AskElectronics • u/princepii • 11h ago
hello everyone,
i am about to buy my first pro dmm. in specific i need a handheld dmm for mobility, common household stuff, dead pcb's, smartphone, tablet and daily electronics repair.
do you have experience with one of these handheld multimeter and which one would you buy as a first professional handheld digital multimeter and why? is there something i have to have in mind when buying one?
are there maybe other better options for a first device?
i would appreciate your opinion. thank you in advance.
r/AskElectronics • u/SatanWasBathed • 1h ago
Total electronics noob here. I'm trying to repair this old Korg LP350 Grand Piano to give away in charity. The sound output has gradually decreased overtime, now I can barely hear it.
I suspect the volume slider ( a 10K Ohm sliding potentiometer, as suggested by Claude, and I checked online it looks same) , is broken, since the sound crackles when I slide it.
Question is, can I 'hotwire' the pins, the red and white ones, without damaging the circuit, so I can diagnose if this part is the problem. If yes, which wires should I be connecting? I can upload more data if needed
Thanks in Advance
r/AskElectronics • u/Fantastic_Win9332 • 1h ago
I am trying out logic gate ICs, this is 74LS-86. I tried to build the full circuit, it did not work, but ic was hot, so I stripped it down to this, and it is still overheating. I wonder why?
This is the kit
https://amzn.eu/d/02skJtuB
I tried 5V and 3.3V too, with the same result
r/AskElectronics • u/Dwtd6 • 4h ago
I opened up an onn 20 inch soundbar to take the drivers and use them on a different speaker enclosure but when i got everything open i saw the capacitor size and all the other components and don’t know if its safe to continue considering capacitors store energy even after the system is powered off (or so i heard). Theres 3 white clips total and to get them out id have to be close to all the components since the speakers top cant be removed and only the front gives access to everything. Capacitor says 68 uf and this is a wall outlet powered speaker
r/AskElectronics • u/Relevant_Pumpkin9190 • 14h ago
Connected 0.1 uf capacitor and Reverse polarity diode to block inductive kick.
r/AskElectronics • u/PearBlaze • 1h ago
Hi guys, I had a random thought and wanted to ask if it's possible.
With the power of emulation, you could get basically any game on a screen. You'd just need to get two screens and hook up all the buttons. And make the two screens foldable. I'd also want this whole thing to be pocket sized and portable. Is this something I can realistically learn to make with no experience?
r/AskElectronics • u/LouisXMartin • 1h ago
Hello,
I'm very new when it comes to electronics but I've some (little) skills regarding arduino.
I'm trying to create a toy to count to 10. The first idea was to use a arduino but I realized it might be done without it.
The main idea of the project is solving addition by only giving a part, such as "x + 1 = 10" or "1 + x = 10".
To make it visual for kids, I'll try to have to button sliding (like an elevator), one of the left, one the right. There will be wires for each pair that makes 10 (L1 -> R9, L2 -> R8, etc)
When the button is pressed, it lights a led. When the two (left and right) are in good position (see the pink wire), and pushed (simple on/off), it should light a third led to say "Left + Right = 10".
I tried to think on how to power this third led only when the sum is 10.
Here is little scheme (paint skill!) to explain the idea.
IA hinted me to use "NPN transistor", but I'm not good yet to understood clearly if it's a good solution or not.
Any help welcome
r/AskElectronics • u/HotelFirm3622 • 12h ago
Hi friends, I built an analog filter and I wanted to generate a 10mv 100khz signal to test my amplification and attenuation, is this possible with an ESP32, I dont have a testbench. Thanks!
r/AskElectronics • u/GlintFortuna • 17h ago
In terms of mechanical disturbances inducing electric noise, how bad is it if, for example, they are used to decouple an op amp in an audio circuit, or if they are outright in the audio circuit itself, for example coupling? I'd assume power supply rejection would do a lot to mitigate the noise in the first case, but what about the second?
Bonus question: if fairly high capacitance was needed for audio coupling (>100uF), and class 2 ceramics (for example, Samsung has 100uF for about 10 cents) were out of the question because of the noise, would electrolyrics be the only good pick in terms of cost for capacitance?
r/AskElectronics • u/Unpopular_Dialogue • 1d ago
I am working on a device/PCB right now and intend to use micro SD cards as a medium of storing the collected sensor data.
The long intervals between data collection (for analysis) and the remoteness of deployment mean that radio data links are impractical. I have left the capability for a radio link open/available if the use case changes but my employer does not want to use that option at this point.
The problem is that I cannot find SD cards of capacity smaller than 32GB to be readily available at scale. I am after about 200 or so 2GB cards; for the first batch. Anyone know any electronic component distributor or retailer that still sells them? Thanks.
r/AskElectronics • u/robertogl • 16h ago
Hi!
I'm buying my first power supply.
Is the Korad KA3305P good? I can find it for 200 euros in EU, I think the other choice would be the Siglent SPD3303C but it is 100 euros more expensive.
I don't plan to have the need for mV precision or high power usage.
Thanks!
r/AskElectronics • u/Silent-Warning9028 • 12h ago
r/AskElectronics • u/dw-luckeylux • 13h ago
I am a beginner, but i have made many such circuits before so i really don’t know what the problem could be.
The cap is 10uF and the resistor values are (top to bottom) 760ohm, 760oh, 270ohm.
I am powering it using ~5v from a battery
The potentiometer has continuity and i connected the wires to the pins properly.
The LEDs polarity is correct. The caps polarity is correct.
r/AskElectronics • u/Dabaduck • 13h ago
I have a Chinese Omron E6B2-CWZ6C NPN open-collector rotary encoder. Although the datasheet specifies a supply voltage range of 5–24 VDC, in reality, the encoder only starts working at around 5.5 V. So I uesed an external 5.5 V power supply connected to the brown (+) and blue (GND) wires, with pull-up resistors (2k Ohm) on the A (black), B (white), and Z (orange) signal outputs.
When measuring the signals with an oscilloscope (no arduino connected and manually rotating the encoder), I get a square wave ranging from 0 V to approximately 3.5 V (the probe/measurement points are indicated by the red circles in the tinkercad image near the resistence).
However, when I connected the outputs to Arduino pins D2 (A), D3 (B), and D4 (Z), I measured up to 10 V. I assumed the voltage was higher because the power supply and the Arduino did not share a common ground. I decided to connect the Arduino GND to the power supply GND, which ended up frying my Arduino ...
How can I interface the Omron encoder with an Arduino using an external power supply? And why did I fry my Arduino?
I'm a beginner any help would be greatly appreciated
r/AskElectronics • u/term1nalN00B • 14h ago
I just need to know if it's safe to clean my + terminal, which is a small brass pin that was glued onto a plastic cap (assuming a layer of glue is causing the problem), with isopropyl or not. Before, it worked fine when the batteries made contact with the poles, but now when testing it just emits small amounts of sparks.
r/AskElectronics • u/Pleasant_Grade • 21h ago
Hi everyone,
We’re developing a compact PCB-based controller that mounts directly onto a 24V solenoid valve using the DIN 43650 Form A interface.
We’re preparing a first production batch of 500 units and trying to solve a mechanical connector issue.
Currently, we’re using TE Connectivity 63969-1 FASTON receptacles soldered directly to the PCB.
The electrical connection works, but the insertion force is higher than we’d like, potentially stressing the PCB and solder joints.
The unusual part is the solenoid terminal geometry:
Approximately 5 mm wide
0.80 ± 0.03 mm sheet metal thickness
Folded U-shaped profile, rather than a conventional flat blade
Approximately 2 mm dimension at the folded section
Two contacts engage simultaneously
We’re considering low-insertion-force FASTON receptacles, open tuning-fork contacts, stamped spring contacts, or other PCB-mounted solutions.
My questions:
Does anyone know of a commercially available PCB-mounted female contact that could work better with this U-shaped terminal?
r/AskElectronics • u/adhamm111 • 19h ago
Will this work? qu1 and qu2 are p channel qb2 is n channel
Max input is 20v
r/AskElectronics • u/i38white • 16h ago
I ended up designing a filter for audio using filter design software and simulated with some variations of parasitics, but am a bit unsuccessful in finding info on choosing the inductor. I have a few questions:
Thanks in advance for any answers
r/AskElectronics • u/redneckerson_1951 • 20h ago
Is anyone aware of a manufacturer that makes Open Wire Line? I know about True Ladder Line and punch line seen at ham fests. What I am seeking is spaced conductors using bare copper wire, no insulation on the wire and 600 Ω.
r/AskElectronics • u/Frenchvanillabang • 17h ago
Idk if this is the right sub but I’m looking for some help with fixing this if possible for my kid. It came from a book that I had as a kid. When the button was pressed the red LEDs would flash and a groaning roaring noise would come from the speaker.
The battery terminal on left (negative side) is mia and the wire that connected it to the circuit board is gone.
Is it fixable, and if so, how?
Fyi:
I know almost nothing about circuits or small electronics like this.
r/AskElectronics • u/Waldvieh • 1d ago

I'm trying to build a small latch circuit for my project with a 1-button Switch ON and OFF logic. I came up with this latch circuit, but my gut is telling me that there might be simpler ways to do this with less components.
The logic is:
D4 is to block the harmful 5V to the uC
D3 is there so i can pull PWR_SW high and detect a Button Push (otherwise both button pins would be on AGND).
I know there are ICs to handle that, like LTC2954, but they are rather expensive and i need a low-cost solution.
Anyone got any ideas how to reduce the component count?
Much appreciated!
r/AskElectronics • u/Dry_Zookeepergame282 • 1d ago
It's a part of a set of flickering candles my mom has. My brother in law dropped it and it stopped working. I spent an hour trying to fix it, resoldered the led bulb to the two wires connecting it, and took a look inside and nothing appears wrong with the soldering. Included are some pictures.
r/AskElectronics • u/TrainerSad3274 • 1d ago
I have to ship out my older computers ddr4 ram to someone I had sold it to online, but I don’t own any anti static bags. I have this hdmi cable that came with my really expensive ASUS rog swift PG27AQDP monitor that looks like it might have came in an anti static bag which would be perfect to ship the ram in.
Let me know if anyone can point out and confirm if it is or isn’t. I don’t want to mess up these ram sticks.