r/led • • 5h ago

Is this an issue with the light itself? And if so, is it a lost cause?

Post image
3 Upvotes

This is a hardwired outdoor porch light that has seen some water infiltration. Half the diodes are dim but not off. The other half of the diodes are brighter and flicker between full strength and half strength.

I’m not totally sure how water is getting in here as it’s caulked all around and has a rubber gasket.

Any tips or should I just get a new one?


r/led • • 14h ago

Fluorescent to LED conversion

Thumbnail gallery
3 Upvotes

I picked up a 20-pack of GE LED15ET8G4840 4' LED bulbs a couple of years ago on sale at Lowes. Was planning on converting a bunch of fluorescent lights to LED. Turns out these wouldn't work with the generic fixtures I had, so I shelved it until later. Well later arrived and I started playing with some of the ballast-bypass solutions online. I've tried applying 120v hot to one and both terminals on either end, with neutral to the other, as well as power and neutral to either pin on one end or the other, but no reaction. Tried the same with a 12v 18a Ryobi battery, but nothing. I figured there should at least be some type of resistance across pins, but nothing with any combination tried. I'm seeing some comments that a Type A ballast is needed, but I'm not sure which one. Would appreciate any suggestions as to which process I need to use, and what part is needed if necessary.


r/led • • 1d ago

Diffuser fill for my LED wizard’s staff

Thumbnail
gallery
16 Upvotes

I built a wizard's staff for our summer camp. I did not manage to finish it on time, but it was functional enough. The staff has a groove with a thin addressable LED strip that does all sorts of effects. One thing I did not manage to finish was sealing off the LED strip in the groove, and I have a problem with what I should use to seal it off.

My problem is that, if possible, I would like to achieve a diffused light strip, where the LED segments are not so visible. At the same time, since the groove is spiral, the filler needs to be dense enough not to run out of the groove when applying.

My main idea was to use hot glue, which I used for fixing the strip to the groove, and I tried a longer strip at the beginning of the groove, but I did not like the outcome (details of that are in one of the photos). Soooo now I am out of ideas and so I have decided to ask the internet people for advice. Any suggestions?


r/led • • 18h ago

Need new 12v power supply for cold weather - how do I replace?

1 Upvotes

I have kitchen LED strip lighting that is powered by a (cheap - see photo) 12V power supply. This has lasted about 5 years, but it's in the unheated garage attic, where it regularly sees very hot and very cold temperatures (Delaware). I've had a couple of other power supplies fail in this location, but this one's a little different - in those cases, I could access the wiring and just replace the whole thing.

I want to replace the power supply only - I need to use the existing low voltage wiring as it is inaccessible. So, a couple questions:

- First, very basic: Any problem to simply cut the low voltage cable from the defective supply and from a new supply and simply wire the new PS to the existing wiring? Can I use wire nuts or do I need to solder?

- Is there a recommendation for a higher quality power supply that can handle the temperature extremes? (I've attached a link to a possible product Power Supply because Reddit says I have to??)


r/led • • 1d ago

Prevent LEDs from getting so stinkin hot?

Thumbnail
gallery
9 Upvotes

Alright okay look. I KNOW there is something stupid and/or simple I'm missing here. I can feel it. But hey listen! I've never done anything like this before and also I went to art school. I ask for your patience in explaining to me like I am 5 and in return I owe you my life.

What it is: I am a dice maker. I am making small Navi (as in the fairy from The Legend of Zelda: Ocarina of Time game) D20 lamps. The D20's are 40mm. It has a holder that lights up and can hold the D20, which is removable to use for games. See Pic 1.

I did my best to 3D model the stand, printed it in PETG, and got these as the light source. See Pic 2.

Reddit would not let me make this post with the Amazon links. I apologize. When I asked to share a non-affiliate link it does not give my a non-shortened URL.

However, within the D20 are some glow

-in-the-dark bits that will need UV to be effective, so I also got these to add to the previous light source see Pic 3.

I am literally just using some wire amd solder to add the extra UV bulb to the center of that little board thing. See Pic 4. For a look at the whole stand, See pic 5.

My guy, this got so goddamn hot. So I got these heatsink star things and some thermal glue. See Pic 6.

But the issue was not solved. Would any of these be the solution?

Probably a very stupid question, but that star board thing IS a heatsink right??? Or is it just what you attach to an actual heatsink? Do I need to attach it to something like this? See Pic 7.

Would a resister like this one that is on the way to me help? See pic 8.

I have elongated the housing for the lighting below the D20. Should I add holes to the bottom as well for ventilation to help dissipate heat?

Any other suggestions?

I apologize ahead of time for my ignorance. These might be an item that are sold at craft fairs if I can figure this out, but I obviously can't do that if they are unsafe.

I deeply appreciate any suggestions and explanations.

Thank you and please save my sanity. 💖


r/led • • 1d ago

How an LED Lamp Works Light From Falling Electrons Animated

Thumbnail
youtube.com
1 Upvotes
How does an LED lamp make light without a hot wire? This animated cutaway shows what happens inside an LED chip: the P-N junction, electrons and holes, recombination, and the photons that become the light you see.

You will see:
• The parts of an LED lamp: dome, reflector cup, chip, bond wire, legs
• N-type and P-type semiconductor
• The depletion zone (the "wall") at the junction
• What happens when the battery is connected, and when it is reversed
• Why LEDs come in red, green and blue (the energy gap)
• How a blue chip and a yellow phosphor make white light
• LED vs filament bulb: where the energy goes

Chapters
0:00 A lamp with no hot wire
0:37 Inside the chip: N and P sides
1:25 The junction and its wall
1:52 Connect the battery
2:27 Recombination: an electron falls into a hole
3:10 Reverse the battery: no light
3:41 Why LEDs have different colors
4:05 White light: blue chip + phosphor
4:25 Dome and reflector cup
4:46 LED vs filament bulb
5:09 The whole story in 30 seconds

Hidden Mechanisms shows the inside of everyday objects as animated cutaways. Subscribe for the next one.

#LED #HowItWorks #Physics

r/led • • 1d ago

RGBCCT LED with Gledopto WLED controller

1 Upvotes

Hi everyone! I bought a BTF-lightning RGBCCT LED strip from Amazon because I wanted the warm and cool whites seperate, but now I found out they are analog and not addressable. Now I don't want to play with MOSFETs to make this work with WLED.

I found a Gledopto ESP32 PWM WLED LED controller (GL-C-211WL) on AliExpress and I wanted to ask if anyone used this and will I be able to power my analog RGBCCT strip with this using WLED? Will the warm and cool whites work? This is the controller:

https://a.aliexpress.com/_EyVOrWe

I dont want to buy another wrong controller so any help is appreciated!

Thanks!


r/led • • 1d ago

led light - to battery - to switch connection issue

Thumbnail reddit.com
1 Upvotes

r/led • • 2d ago

My company was going to throw this in the trash. The transformer blew up in it and they let me take it home. The transformer had a 42v secondary so it was prefect for two Milwaukee batteries in series. I used the center tap and each battery(with resistors) to run two 12v spdt relays for high(all of

Thumbnail
gallery
15 Upvotes

It's super bright and doesn't kill the batteries at all


r/led • • 2d ago

I made a candy cane with a 555 timer and some leds. It ran for 35 days off of one charge (18650 battery) before i turned it off.

20 Upvotes

r/led • • 1d ago

Looking for information on the 4-Pin interface sensors

1 Upvotes

Anyone know anything about this port? I'm familiar with sensors that connect to the 3 pin port but cannot find anything about the 4 port.

https://www.amazon.com/dp/B0DC9SB7KM


r/led • • 1d ago

Need Help Choosing a Compatible Replacement LED Driver for My Lamp

2 Upvotes

Hello, I have an LED lamp, and the driver just stopped working. I didn't know what to do at the time, so I recycled the old one, and I've been trying to buy another one ever since. I'm a newbie in this domain, so I would need some help.

The LED driver is directly on the plug.

THE OLD LED DRIVER

The first photo is of the old one. I tried to find a new one, but I cannot find the exact same specifications on the local market, and I don't know how much flexibility I have when looking for alternatives.

THE ONE I FOUND IN A LOCAL STORE

The second photo is of one that I found in a local store.

My questions:

  1. Does it fit?
  2. If not, what should I look for? Which specifications must be the same, and which ones are flexible?

Thank you!


r/led • • 2d ago

Open-source Artnet PIXEL LED controller now has 24 Universes!

Thumbnail gallery
4 Upvotes

r/led • • 1d ago

skydmo ambilight com defeito

Post image
1 Upvotes

Minha fita de led ambilight skydmo deu esse defeito da imagem.

Está acendendo somente uma zona de led que é a mais próxima do cabo.

Tem alguma solução para isso ou não tem reparo?


r/led • • 2d ago

How do I power this string of parallel LEDs ?

Post image
1 Upvotes

r/led • • 2d ago

Made a demo project with WS2812B-4020 & XIAO ESP32C3

Thumbnail
gallery
12 Upvotes

I've used WS2812B addressable LEDs in several projects, mostly the standard 5050 and 2020 packages.

Recently, I came across a less common variant with a right-aligned LED position inside the package (WS2812B-4020). I thought it would be interesting to experiment with it.

I designed a small flexible PCB, ordered it from JLCPCB, soldered a Seeed Studio XIAO onto it, and wrote some code to test the LEDs.

Just a small experiment to explore a different LED package.

Have you come across this variant before? What kind of projects or applications would you use it for?

I'd love to hear your ideas!

Find the LEDs link in the comments


r/led • • 2d ago

Homemade 100w 35v flashlight It's got a timer so the fan will stay on after i disconnect the power. Is powered through. The light is powered through a 300w constant current converter module which is powered thru a 12v sptd relay for low current switching. Etc...

Thumbnail gallery
6 Upvotes

r/led • • 2d ago

Are there fairy lights with LEDS each .5 inch to 1 inch apart?

Thumbnail
gallery
7 Upvotes

I need help finding some LEDS / Fairy Light strips for a project I'm doing. I'm trying to light 11 hollow, 3d-printed models with wall thickness of ~1mm. Right now they look very good with my Iphone 15 light illuminating them from the bottom. I've provided some more context for the project:

Current Problems:

- Iphone Light is not permanent, need a corded LED/Fairy Light I can plug into an outlet or a usb port.

- Single point of light from my Iphone is not sufficient enough to light the top of the models (many are tall and thin). I get a bright point at the bottom and the top remains dark.

My current idea is to wrap a string of fairy lights around a center pole to provide more evenly distributed lighting. I don't know which lights will be powerful enough to light the model without being overly bright or importantly too heavy (these are light models, thick led strips pushing the inside could knock them over).

I've added a picture of the type of lights I think might work but I'm afraid the LEDS are not close enough together / not bright enough.


r/led • • 2d ago

Baomain illuminated push button led color comparison

Thumbnail reddit.com
1 Upvotes

r/led • • 3d ago

Mr Christmas ferris wheel - brightness adjuster?

Thumbnail
gallery
2 Upvotes

As the title suggests, I am looking for ways to adjust the brightness on this Mr Christmas Ferris wheel that I have. I have no idea where to start or to which points I would need to connect a dimmer to.

So far I have purchased a pwm dimmer and hooked it up to the ground and vdd in line, looks like that did not work.

With a multimeter, I've tested the voltage between ground and vdd when it is on, and it's just under 3 volts. 2.97 to be exact.

Any help would be greatly appreciated.


r/led • • 2d ago

Teste dein Glück bei unserer täglichen Verlosung, die auf de.olight.com stattfindet. Jedes Mal, wenn du das Glücksrad drehst, kannst du einen Preis gewinnen. Jetzt teilnehmen!

Thumbnail de.olight.com
0 Upvotes

r/led • • 3d ago

Help, I got really excited when I unboxed my new grow light and saw 2 plugs that fit together and I plugged them in without plugging in the LED driver between them. Did I break my new light?

Thumbnail gallery
1 Upvotes

r/led • • 3d ago

Can only get orange with plastic remote not app on RGBW Neon strip?

1 Upvotes

So I bought and installed:

Yescom BiLume RGBW Neon Rope Light App & RF Control 120V Outdoor IP65 × 2 100ft

https://www.yescomusa.com/products/neon-rope-light-flexible-150ft-rgb-app-rf-control?variant=51854968586421

And with the remotes that came with them I can get orange/amber/yellow from the preset buttons, but on the lotus lantern app I'm unable to or am missing something?

On the App if I set:

R255/G0/B0 I get red

R0/G255/B0 I get green

R0/G0/B255 I get blue

So I think the pin setup is right. But if I try selecting any other red or orange or yellow I get varies shades of green.

I've tried selecting all sorts of combos of colors and CCT and W selections but can't figure out what I'm missing on why I can't get those colors via the app.

I'll use the remote if I have to, but would very much like to get the app to work if I can.