If your MOZA setup isn’t working correctly in Forza Horizon 6, here’s a quick guide that should help resolve the most common issues:
1. Game Installation
It can be installed via official channels such as Steam. If you have performed a custom installation, you will need to specify the directory for Forza Horizon 6 in the Pit House game list.
2.Force Feedback Settings
All the MOZA Racing Wheelbases support Force Feedback.
3. Telemetry Configuration
After entering the game, click ‘Settings’.
After entering the settings, click on ‘HUD & Gameplay’, turn to the bottom.
Set ‘Data Out’ to ‘On’
Set the ‘Data Out IP Address’ to ‘127.0.0.1’.
Set the ‘Data Out IP Port’ to ‘20066’.
Once you have completed the above steps, you will be able to obtain telemetry data via the steering wheel speed indicator and the instrument panel.
4. Device Control Mapping
You will need to configure the control mapping when you launch the game for the first time.
To enter the game, first click on 【Settings】to enter the Settings page.
After entering the Settings page, click on 【Controls】, and Select 【Change Input Mapping】
Note: Buttons displaying a yellow exclamation mark in the game interface UI must be bound; control presets will only be maintained once binding is complete.
▼ Why is there no force feedback in Forza Horizon 6? Other games work fine.
If there is no force feedback when using the MOZA Base in “Forza Horizon 6”, you can troubleshoot in the following way:
1.Firstly, keep the steering wheelbase connected to the computer
Please disconnect the handbrake, shifter, pedals, third-party steering wheel and other peripherals first, leaving the MOZA base for the first binding.
2.Set the preferred device in Windows
Open the Windows Game Controller Settings, set MOZA Base as the preferred device, and then re-enter the game to bind the steering wheel.
3.Confirm that the MOZA Base in the game is “Device 1”
The Horizon series typically outputs force feedback to “Device 1”, and it is necessary to confirm the binding in the game control.
4.After completing the Base binding, connect the other devices one by one.
The suggested sequence is: first, binding the base → confirm the force feedback → then connect the handbrake/shifter and other accessories → rebind one by one.
You can also check the full official setup guide here:
My R9 v2 died a couple of days ago, out of warranty decided to open it up.
Was dead, nothing at all when turned on, and pc didnt saw it. Tested the power supply and it was good. Noticed when i pressed power that led would turn on.
Decided to risk it by buying a board from support and let me tell you, that was fast and easy.
They would reply early in the morning of the next day, every time, with clear and easy instructions. After a few messages and photos they asked for to make sure they send the right board.
Took 16 days from chine to portugal, arrived very well packaged and fixed my problem right away. you can see where the old one burned.
People usually only report negative feedback, wanted to leave this here. May help someone fix their out of warranty base.
I'm currently running a Moza R5 bundle with the stock SR-P Lite pedals. They're currently going back under warranty (accelerator not registering in Moza Pit house), so I'm thinking about upgrading instead of just getting them replaced.
My main issue besides the fault is the noise. It produces loud clunks when the pedal gets released abruptly and hits the end stop. I’ve tried putting soft pads on the metal parts that make contact, but it didn’t do much and the clunk is still there.
So my question is : are load cell pedals noticeably quieter in practice? I'd expect elastomers and a shorter brake travel to help, but I'd love to hear from people who actually own LC and/or made the switch.
I'm considering selling the srp lite for a SRP2 (or CRP2) + clutch
If you own any of these, how loud are they? Do the throttle or clutch also clunk when you release them quickly? And if somehow, someone found a good fix for the SR-P Lite noise, I'm all ears.
I have no force feedback on assetto corsa, when i start playing about 2 weeks ago it happened but a simple restart of the game would fix the problem and now even restarting the games multiple times it wont work.
It entirely depends on luck sometimes from what my experience, and i tried disconnecting and reconnecting the wheel in game still don't work.
Also does anyone have the same problem on ACC i am planning to buy because of the sale, if you guys experience the same problem on ACC maybe i won't buy.
On the 20th I got my r3 in the mail and the night i got it i set it all up and i wanted to play farming simulator 25 with the soft limit set to 900, 450 on each side. How do i enable it after it worked for the first night and it hasn't worked at all since Friday night and I have tried almost everything it my first ever wheel base from moza.
last update on moza pithouse cause r5 base disconnect and reset shortly after use, no way to use wheel. try rolle back last three firmware ubdate but no diference they reset all the time.
The only thing I didn’t like about my KS Pro was the plastic used for the knobs. So, I found some aluminum replacements online and have tried various configurations. I like using the smaller 21mm knobs on the numbered rotaries to show the full LEDs. I’d seen this kind of look on BavarianSimTec wheels and wanted to try it on the KS Pro.
The anodized aluminum knobs and funky switches feel so much nicer.
I also added some thin foam pads on the shifter paddle magnets to shorten the travel a little bit and make it require less force to shift. Also makes them quieter.
Between mods and customizing advanced dashes with Azom, you can really make this wheel exactly how you want.
I purchased the knobs from SimRaceMods, buy any knobs made for 6mm D shaft potentiometers will work for the rotaries.
I am probably going to pick up some of the new haptic pedal modules so I can feel some of the road and tell when I actually lock up the breaks in dirt rally 2 but I dont know anyone who have actually used them on a rally game. Anyone have experience and can tell me whether they think its worth it or not?
I recently purchased the R3 bundle to see if I would enjoy sim racing/driving as I am a school bus driver for my day job and absolutely love it. I've driven many air brake and mechanical brake busses, as well as driving multiple cars regularly. The brake pedal that comes with the R3 bundle is the most stiff and hard-to-use pedal I have used in my entire life; requiring more force to fully press down than an air brake pedal. This has left me demotivated to use the brake at all.
I keep looking this issue up online and have found no solutions of any kind, as well as very few people with this complaint. Instead, I find band-aid fixes like "change the max distance in pit house" which doesn't address the fact that any distance on the pedal is very hard to achieve as it has the same stiffness all the way through. I also see people say it will break in, but nobody says it magically feels soft and usable after it breaks in, and instead I see people claim that it's normal that it's this difficult to use. The biggest issue with breaking it in is that I feel demotivated to use the brake at all due to how hard it is to use in any capacity.
I see some people saying to use the performance kit, but there isn't one available on the moza website for these pedals -- with the only kit being for the Lite2 pedals. Is there something I'm not understanding about these pedals? I've seen a comment from a GT driver (don't remember which post) who had also claimed the pedal is a bit too stiff and doesn't represent the real thing, but sadly I'm yet to drive in an actual race car so I do not have my own personal experience in one. From what I read about them, it seems most are just slightly harder to brake than a road car, but nothing like this. I would like to return this bundle and get the R5 bundle so I can try using the SR-P Lite2 pedals with the performance kit, but I don't believe I am eligible for a return according to their policy since I already opened and used it (it has not been 14 days, and sadly I ordered directly from moza).
I knew I wasn't getting a brand-new product, so I was prepared for some cosmetic damage. That's perfectly fine. What I wasn't expecting was the absolutely terrible packaging and missing parts.
Apparently, nobody thought it was worth checking whether the box actually contained everything. I'm missing screws and the tool needed to tighten them. Great quality control, MOZA!
I'll try to find some screws and something to mount the wheel with. Hopefully, the thing actually works. I'll update this post once I've tested it.
So I got the R16 Ultra as soon as it was released and I’d like to know if anybody is having the same experience or at least has a fix action. I only play iracing so I really have no idea if this is a game only issue but if it is then I’d like to know how to fix it in iracing. So far, the R16 Ultra has just never really seemed right. While racing or practicing or doing whatever I’m doing on iRacing, I’m getting a constant “notchiness” or like a “clicky” feeling with the FFB. Mostly on turns but also while going over some road details. It doesn’t do it normally or without FFB so I don’t believe it’s a hardware issue. I’ve tried to change so many different settings and force effect recommendations and the feeling just never goes away. I used to have the R12 which was super smooth and felt amazing so I know this isn’t a normal feeling to have. I’ve even gone into the iracing game files and tried to turn off the 360hz setting which made it way worse somehow. I’m just super frustrated because the wheelbase obviously wasn’t cheap and I really don’t want to do the whole mail-in process for a hardware fix if that isn’t even the issue. So, if anyone has any advice then I’d love to hear it.
EDIT: before people ask, no I don’t have a video of what it’s doing because it’s not something you can see visually
UPDATE: so it’s still not fixed completely, I think the rest is up to a firmware update as long as I’m not the only one experiencing this. However, I was able to get it as comfortably close as I remember the R12 being. The golden setting that helped it was actually turning off the hands-off protection. I also turned up the interpolation a little so that might also be part of it, but it didn’t really get “fixed” until the hands protection was disabled.
Ordered the refurbished r5 and arrived on 11/3. Filed a ticket on 11/6 because it has no force feedback. After sending the error file, they said the power supply is broken, so they said they’re shipping one to me on 11/9. As of today 11/20 (not even at my local usps office yet), I still don’t have a working r5. Because apparently, they ship their parts from China. You would think they’ve tested every refurbished product before shipping them. But no, a simple plug in and testing would’ve noticed it was broken. This must’ve been an ongoing issue within their QA (if there even is one), I’ve seen so many people talking about a non working refurbished product after encountering the issue of mine. I don’t expect a brand new product buying a refurbished, but the item was randomly placed inside the box I guess from the previous customer when it arrived with a few bolts still screwed in and a non-working product.