r/raspberrypipico • • 14h ago

help-request Raspberry Pi Pico H Project Advice

0 Upvotes

Hi everyone! I'm a first-year, first-semester student, and I need some advice in choosing a project for my final assignment.

It's an individual project using a Raspberry Pi Pico H with MicroPython. The requirements are:

- At least 3 physical inputs (including 1 analogue ADC input and 1 digital priority input).

- At least 3 physical outputs (including 1 digital output and 1 PWM output).

- 3 operating behaviours: normal operation, priority event, and recovery.

- Implement and compare 2 software techniques using a baseline and an improved program.

- Demonstrate everything through both Wokwi simulation and actual hardware.

I'm currently in Week 9 out of 14, so I still have more topics to learn, but I've done searching and here are some ideas I've been considering:

  1. Wind monitoring system: Measures wind speed using a DIY anemometer (i already search how to make it in youtube) and gives a warning when wind conditions are too weak for wind turbines.
  2. Water leakage detection: Detects unusual water flow or household leaks and alerts users.
  3. Drain and flood monitoring: Monitors water levels and rainfall to provide flood warnings.
  4. GPS navigation device: Uses GPS to display location and provide basic navigation or emergency alerts.
  5. Face recognition access control for classroom attendance: Uses OpenCV on a computer to recognise faces and communicates with the Pico to control access.

I'd love to hear your opinions and advice, since i'm still a beginner in this field :)

- Which idea would you recommend for a first-year student? (based on the difficulty, efficiency, sustainability, cost)

- Are there any technical problems I should consider?

- Do you have other interesting ideas that might fit the requirements better?

I'm open to suggestions and improvements. Please do ask me if u need any details from the ideas i have. I'll try to answer them, thanks!


r/raspberrypipico • • 16h ago

RP2350 vs STM32, ESP32 & Arduino – Real Benchmarks | RP2350 #22

Thumbnail
youtube.com
0 Upvotes

r/raspberrypipico • • 21h ago

[Review Request] 4 layer RP2040 + USB-C board, 50 x 49 mm, KiCad 10

Thumbnail gallery
2 Upvotes

Hi friends, I would like a review before I order this. It is a small RP2040 board with USB-C, 7 LEDs, BOOT and RESET buttons and a push switch.

Gallery order: 1 top composite, 2 to 4 3D views, 5 to 8 copper layers L1 to L4, 9 full schematic, 10 to 14 schematic zoomed in sections, 15 stackup and impedance table.

Board

  • 4 layers, FR4 Isola 370HR, about 62 mil, 1 oz copper on all layers
  • L1 parts and USB pairs, L2 solid GND, L3 3.3 V plane, L4 other signals
  • 50 x 49 mm L outline, four M4 plated holes tied to GND, all parts on the top side
  • USB pairs: 5.0 mil trace, 4.0 mil gap, 90 ohm differential, on L1 over L2
  • 6 mil min track and space elsewhere, 8 mil min drill, 8 mil drill to copper, 12 mil tented through vias, IPC Class 2, 1 A max
  • KiCad DRC and ERC are clean
  • Layout was scripted and most non critical nets were autorouted, so it is not hand tidied

Questions

  1. USB pairs at 5/4 mil on L1. The fab table says 89.7 ohm, my field solver says about 94.5 ohm. Is that a yield risk?
  2. The stackup table shows 0.5 oz inner copper, but I am using 1 oz inner. Does that change the impedance enough to worry about?
  3. Five tented 12 mil ground vias in the RP2040 centre pad. OK, or should I move or fill them?
  4. The USB-C footprint is custom from the datasheet (0.40 mm holes, 5.5 mil annular ring, 0.60 mm shell slots). Anything wrong?
  5. 8 mil power neck downs at the RP2040 pads (16 mil elsewhere) with a 1 A max. Fine?
  6. L4 routing: return paths, anything crossing plane gaps, anything a fab would flag.
  7. One sided assembly with a through hole push switch and USB-C. Any assembly problems?

KiCad 10.0.8. I can share Gerbers or the project if that helps. Thanks!