r/3DScanning • • 6h ago

Scanned my Bosch tools with the Creality Pika and turned the scans into snug-fit Gridfinity bins – scan → script → verified print

Thumbnail
gallery
35 Upvotes

I've been wanting proper Gridfinity homes for my measuring tools for a while, but modeling contoured pockets by hand for oddly shaped devices is a pain. So I tried a scan-based workflow instead – first result is a bin for my Bosch GDH 1-17, more coming.

The workflow

  1. Scan – Scanned the device with the Creality Pika (Creality Scan software), exported as a watertight STL. The scan noise is still visible in the raw mesh, which is why step 3 matters.
  2. Align – A script auto-orients the scan: display face up, long axis along X, tilted slightly to get the lowest possible height (saved a few mm → one Gridfinity unit less).
  3. Generate the pocket – Instead of just booleaning the raw scan (which gives you every bit of scan noise and undercuts), the pocket is built from a height map of the underside:- vertical walls so the device lifts straight out (no undercuts)- 0.5 mm clearance all around- smoothing that is only allowed to *remove* material – the pocket can never get tighter than the scan, but the surfaces end up looking modeled instead of scanned- screw holes and small recesses in the device are bridged, so no little "noses" poking up
  4. Finger grips – straight-walled slots along the outer wall on both sides, deep enough to actually get your fingers under the device. Outer wall and stacking lip stay intact.
  5. Gridfinity body – standard base profile and stacking lip, smallest grid size that fits, device sitting as high as possible while the bin stays stackable.
  6. Verify before printing – the script checks:- overlap volume between scan and bin = 0, even with the device shifted 0.3 mm in every direction- base profile and stacking lip measured on the final STL against the Gridfinity reference dims (caught a bug in an early version where the 1.8 mm vertical section of the base was missing – glad I checked)

Full disclosure: I wrote the scripts together with an AI assistant (Claude). The scan, the design decisions and the test prints are mine, and the model is tagged accordingly on Printables.

Result: 6x2x8 bin, prints without supports, device drops in and comes out easily, display readable without taking it out.

Printables: https://www.printables.com/model/1925293-gridfinity-bin-for-bosch-gdh-1-17-contoured-insert

More bins coming over the next weeks – a Bosch GLM 50-27 laser distance meter is already designed and others will follow. Happy to hear which tools you'd want to see, and I'm also happy to answer questions about the workflow.


r/3DScanning • • 1h ago

best scanner for hands and faces

1 Upvotes

I'm just starting with 3D scanning and I bought a POP4 this summer.

It's good for colors but I can't get any skin details. I want to replicate faces and hands in 1:1 and I only care about the meshes/sculpt and not the colors.

Someone from the revopoint forum told me I would never get what I want with it and said to buy a MINI2 + range 3 and mix the scans. But online they said that MINI2 was not good for faces so I'm running in a circle.

It's black friday so a good time to buy.

Do anyone has some advices on what would be the best under budget (2000, less is better).


r/3DScanning • • 5h ago

Scans full of holes and noise? I built a free tool that cleans them up and exports solid STEP

2 Upvotes

A friend of mine has a 3DMakerPro scanner and kept asking me to help clean up his scans so he could print replacement parts or open them in SolidWorks. I'm a mechatronics engineer working in software, not really a 3D person, and I couldn't find an easy path. The STL opened as a graphics body, I couldn't get a proper part, and I couldn't even get the mesh closed without holes.

So I built a browser tool for him. You drop in a scan (STL, OBJ, PLY) and it:

- closes holes and removes floating junk

- smooths noise, with a protect brush for holes that should stay open

- snaps cylinder-ish areas to perfect cylinders and flat areas to real planes

- exports a solid STEP for SolidWorks / Fusion, plus STL and 3MF for printing

Free, no account, and it runs entirely in your browser, so your scans never get uploaded.

garbagetocad.com

I'd love to hear what scanners you use and which scans break it. Send the ugly ones my way, that's how I'll make it better.


r/3DScanning • • 8h ago

[Request - Tacoma, WA] Student looking for a local 3D scanning hobbyist to help scan a classic car for a woodshop project

2 Upvotes

I’m a high school student in the Tacoma, WA area working on a woodshop and CAD fabrication project. I’m designing and building a full-scale wooden body buck of a 1969 Shelby GT500 Convertible in Autodesk Fusion, and I need an accurate 3D mesh of the exterior to slice my cross-sections.

I am currently reaching out to local collector car owners to get permission to scan a car, and I’m looking for a local hobbyist or enthusiast with a large-object handheld scanner (like an Einstar, Revopoint Miraco, Creality Otter, etc.) who might be willing to help me capture it once I lock in a date and location.

A few important details:

  • 100% Contactless: Since this is a rare collector car, we cannot use adhesive tracking dots or scanning spray on the paint—so a markerless/feature-tracking infrared or structured-light scanner would be ideal.
  • Time & Location: Likely around Tacoma / Pierce County (or nearby South Sound), taking about 20–30 minutes depending on the owner's schedule.
  • What I need: Just a decent exterior surface mesh (.OBJ or .STL) with accurate overall proportions for slicing plywood stations in Fusion—it doesn't need sub-millimeter engineering tolerances.
  • What I can offer: A chance to scan a really cool classic Shelby, credit on my project, and I can also try to cover a small thank-you/gas stipend if needed.

If you're local to the South Sound / Tacoma area and interested in helping out (or have advice on tackling a glossy car markerless), please drop a comment or DM me!

Thanks!


r/3DScanning • • 19h ago

How to add thickness only to single-sided/non-manifold areas of a high-poly scan?

Thumbnail
gallery
4 Upvotes

Are there any tools that can add thickness only to those parts of a scan that currently lack it? The complex geometry of the skull includes both closed volumes and surfaces that have no thickness. Standard thickness modifiers—like those in Fusion 360 or the "Solidify" modifier in Blender—don't work in this case. I am unable to rebuild the model from scratch based on the scan, and performing a "remesh" in Blender isn't feasible due to the massive number of triangles.


r/3DScanning • • 16h ago

3D Scanner for plastic fenders

2 Upvotes

Hi guys, I have a side project I’m working on for a relative of mine for remaking some fenders for a Yamaha 225DX three-wheeler.

We have the original OEM fenders but are in subpar shape so our goal is to get them remade as a replacement to the original fenders. I currently work in the Additive Manufacturing industry and have experience with 3D printing and the post-processing of those components so I’ve been brainstorming ideas of ways I can incorporate the two together. I’m reaching out here because I’ve been considering the additive route to recreate these fenders but my main roadblock now seems to be an accurate way to create models to then have printed. I’m looking into using the 3D scanner route as an avenue into creating the most accurate models as possible as something like creating a mold seems to be a less accessible alternative for my current situation. Is there someone out there or a way to rent a higher-end scanner to have these parts scanned? Or is there another option that may be a better fit for what I’m looking to accomplish? I have more experience in the physical aspects and finishing process of the AM industry so I’d be interested to hear any opinions or other unique options you all may have!


r/3DScanning • • 22h ago

3D Scanning Comparison: Creality Raptor Pro vs. Ferret Pro

Thumbnail gallery
4 Upvotes

r/3DScanning • • 22h ago

Lenovo ThinkEdge Server

Thumbnail
gallery
4 Upvotes

After a week or so of experimenting, scanning in some old projects, some frustration with the new(to me) software, poking at and changing settings, I have gotten enough of a handle on the Metro Y to try a real client object.

The Lenovo ThinkEdge SE-100 is a 1U high but otherwise 1/4-sized version of one of Lenovo's standard Core i7 "pizza box" rackable servers.
Specs here for the curious: https://www.compsource.com/buy/7DGR1001NA/Lenovo-1223/Thinkedge-SE100-7DGR1001NA-Server

For us here, the important specs are that it's matte black metal casing where cooling fins and angular surface geometry are part of the case itself.
From the side, the profile looks like __/---__/---\.
Just to make it even more fun, there are a pair of fans are recessed deep inside the case itself.

I scanned on a dark table with markers placed around it(It covers the markers on the included turntable) and added a few to the edges of the server itself.
The settings were: CrossedLines scanning, Marker Mode, High Accuracy, Black Object.

I made 9 passes from different sides and angles as separate scans and used 6 of them. I did selective hole-filling vs. letting Metro auto-fill them because I was almost certain it would mess up the opening around the fans.

One additional thing I might try would be a scan of the tops side in single-line mode to see if that catches the space between the cooling fins better than cross-line model which left a lot of holes in those spaces between the cooling fins. For now the hole-detection & filling function did a good job patching them.

Overall, I'm actually quite happy. There's a lot of purchase validation wrapped up in those screenshots there.


r/3DScanning • • 1d ago

Formnext 2026 - The Year of the Tool Changers (+ Desktop Mills & 3D Scanners)

Thumbnail
youtu.be
6 Upvotes

I was at Formnext in Frankfurt this week and here is a short overview of the new products that interested me most. I focused on three topics: desktop mills, the flood of new tool changer 3D printers, and of course 3D scanners.

Desktop Mills: Infinimaker 5-axis mill with automatic tool changer (~$5,700, ships to companies only) and the public premiere of the Makera A1S (2,800 € base, 4,250 € with tool changer and flood cooling), compared to the Tooldance X1 I backed on Kickstarter.

Printers: This is the year of the tool changers. Creality K3 (850 €, flexible filament kit release in February), Axiloop with 8 nozzles, Co Print Quadro, Elegoo Centauri X Ultra and the Infitech MX. Plus CMYK color mixing prints, a metal printed turbine and the SnowX metal printer starting at roughly 5,000 €.

3D Scanners: 3DMakerPro Turtle and a laser scanner prototype, 3DeVok Pico Pro (~1,500 €), Creality Raptor Pro Max and P1S, Elegoo M1 Ultra and the Revopoint Miraco 2 with PMK kit.


r/3DScanning • • 1d ago

Where in Austin should I 3D scan next?

2 Upvotes

r/3DScanning • • 1d ago

3D scanning a DeWalt impact driver housing with the Revopoint MIRACO 2

Thumbnail
gallery
64 Upvotes

I recently used the Revopoint MIRACO 2 to scan a DeWalt impact driver housing for a reverse engineering project.

The part has quite complex geometry, with several internal and external features, deep cavities, structural ribs, clips and embossed lettering on both plastic and rubber surfaces.

The entire scanning process was carried out in standalone mode, without connecting the scanner to a PC.

I used Parallel-line Laser mode with Global Markers for tracking, the Generic object setting and a point distance of 0.15 mm.

To capture the entire housing, I performed two separate scans, rotating the part by 180° between acquisitions. The point clouds were fused at 0.1 mm directly on the scanner.

I then imported both scans into RevoScan 6, where I cleaned up the data and removed unwanted areas. I also trimmed the marginal regions that had not been captured properly before using the automatic alignment function to merge the two scans.

Finally, I generated the mesh at 0.1 mm resolution.

I was particularly impressed by how well the scanner captured the internal geometry, including the deep cavities, clips and small structural details. No matting spray or surface treatment was needed; I only cleaned the housing to remove the grease inside.

The resulting model provides a detailed reference for CAD reconstruction and the design of custom replacement parts.

I'm curious to hear what you think about the result and the workflow.

Have you used standalone scanners for similar reverse engineering projects?


r/3DScanning • • 1d ago

my scanner needs a pruchase verification which i don't have what to do?

1 Upvotes

so i got a 3d maker pro seal as a gift and won't automatically connect to my pc (for some unknown reason) the software makes me do it manually but to do so i need to send the device's label and proof of purchase, problem is, since it is a gift, i don't have a way to recover anything like an online order or anything with a purchase date like the website asks me is there any other way to do it?


r/3DScanning • • 1d ago

VW T-Roc Cabrio - Einscan Trak and Rigil combined

Thumbnail
gallery
14 Upvotes

Anther car scanned with my Einscan Trak for a project. Pattern continues: scanning itself takes roughly 30min, processing another 30min to get a fully aligned scan.
This scan was a bit more special since I also scanned the car interior with the Einscan Rigil in IR mode to quickly capture the whole interior. Scans were later merged within Quicksurface to get one final scan.

Scanning

Scanning was done at 1,5mm target point distance with four tracker positions. I attached a diagram showing the positions and the rough tracker FOV and overlap.
Lights were covered with scan spray to allow scanning them. All four scans combined took 30min. What I also noticed: When getting very close to the edges of the tracking area scanning starts to become slower, much like the WiFi signal drops out. But it actually is the border of the scanning area. Scan itself was at a constant 90FPS when placed within the tracking volume.
After scanning the car with roof closed I created another scan of only the roof section with the roof opened to capture the transition.
Rigil interior scan was done at 1,5mm target point distance and hybrid tracking in IR mode (features + texture) to quickly capture the whole interior.

Post-Processing

Trak doesn't require point cloud generation after scanning, you just pause the scan and either create a new scan or go on with processing. So I aligned the four scans using automatic feature alignment and then meshed them in default settings with semi-watertight settings. Same process applied to the Rigil but there was no alignment needed since it was only one scan.
Later exported into Quicksurface for postprocessing: I aligned the car scan to the global coordinate system and then used point picking and automatic fine alignment to fit the Rigil IR scan within the Trak scan.

Results

Overall scan result is quite impressive and well enough for my use application. Especially the texture result of the Rigil are very good, for merging with the Trak scan I didn't need the textures so omitted them.

PC Specs

Since a lot of people ask for it:

  • AMD Ryzen 7950X
  • 128GB DDR5 RAM
  • RTX 5070Ti Desktop
  • A few TB of NVME storage with PCIe Gen4 interface

r/3DScanning • • 1d ago

Feedback wanted: non-LiDAR room scanning app for architects & interior designers (iPhone/iPad beta)

Post image
1 Upvotes

Hi all, I'm the CTO & Co-Founder of Scanbrix, an iOS app for scanning interiors, and I'm looking for honest feedback from people who know scanning.

What's new: you no longer need a LiDAR device. The app reconstructs the room on-device from photos, so it works on non-Pro iPhones and iPads too.

Who it's for: architects and interior designers who need quick as-built captures of residential spaces.
Attached is a raw scan preview of a bedroom, captured on a non-LiDAR phone with no cleanup. You'll see holes and artifacts around reflective and occluded areas. That's exactly the kind of thing I want to improve.

What I'd love feedback on:
- Capture experience: was it clear how to scan?
- Mesh quality and texture vs. what you'd expect without LiDAR
- Measurement accuracy, if you can check against a tape
-What export formats or workflows you'd need

This is not live in the app available on App Store, you can download the beta (TestFlight) here: https://testflight.apple.com/join/kqFq7yea

Happy to answer questions about the pipeline. Thanks in advance!


r/3DScanning • • 2d ago

From a messy forearm scan to a cast-ready mesh: hole filling, denoising and wrist/finger reposing (demo)

18 Upvotes

Brazo, end to end: a raw scan of a hand and forearm goes in, a ventilated cast ready to 3D print comes out.

The holes get filled, the wrist gets straightened, the cast design is carried onto the arm and the pieces are laid out on build plates. No landmarks to place, no mesh to mend by hand.

I'm letting people in a few at a time. If you're an orthotist, hand therapist or clinician, or you run a 3D-printing service, join the waiting list:

https://brazo-waitlist.geometryweave.com/


r/3DScanning • • 1d ago

Iscanned my induction charger using the new Miraco 2 from Revopoint

Thumbnail
gallery
2 Upvotes

The results are excellent. I imported the stl file into my 3DSRE software to Export step.

Scanner: Miraco 2

Software: Revoscan 6

Reverse: 3DSRE (with Claude)

Scanner : Miraco 2 https://revo.ink/4eqAAYv

Software : Revoscan 6

Reverse : 3dser (with claude ) https://drive.google.com/.../1XRm2IAzRyK...? usp=drive_link

Don't forget our group discount for Revopoint and ATTBLIME in the guide section.


r/3DScanning • • 1d ago

Holiday Scanner Recommendation Request

2 Upvotes

Hello!

I am looking to get a 3d scanner for scanning people to do 3d prints of cosplays and will likely do some minor reverse engineering like scanning the 2" step into the kitchen to make a custom fitted ramp. I do also want the color scanning.

For reference I have a asus zenbook pro duo so a fairly beefy laptop

With this in mind i went to buy the revopoint range 3, but am now getting emails to send in my photo id and it feels suspicious.

First of all, it's this legit?

Second, should I just refund the order and go with av different scanner? Is there something else that would better fit my needs?


r/3DScanning • • 1d ago

ExStar Mobile finally available on iOS (with speed iPhone 16 speed test)

Thumbnail
gallery
2 Upvotes

Finally the ExStar Mobile app made it trough AppStore approval and is available for download (currently compatible with Einstar Rockit, Einstar 2 and Einstar EZ GO). App can be downloaded on iPhone and iPad. Since my "old" iPhone 16 already reaches the max possible scan speed the iPad with Apple Silicon chips may have the most advantage when post processing the scans.

Already did a quick first test with my iPhone 16 (keep this in mind: two years old, not pro model) and here are the speed results:

  • Laser mode (marker tracking): stable 60 FPS
  • Laser mode (markerless laser mode): stable 20 FPS
  • IR mode (hybrid tracking: geometry and texture): stable 20 FPS

Quite happy the app is finally released and that the hardware requirements are this low.


r/3DScanning • • 1d ago

3D scanner recommendations but focused more on software?

3 Upvotes

I've been researching and it seems like both the Creality and Revopoint software aren't well liked. I need to purchase a scanner and need good accuracy (Raptor Pro or better) but people don't seem impressed with either the Raptor Pro or the Metro Y when using them with their bundled software. I do a lot of reverse engineering so the addons from Revopoint seem appealing. What are your thoughts? Any other brands in the same ~$1,200 on sale category that do a good job with accuracy? That's the most important part, I can wait on slow processing. I'm fairly easy to please, I just want scans to not loose tracking (Creality?) or weird artifacts when merging scans (Revopoint?) or jagged edges on pillars, etc (Revopoint?). Accurate, easy scans that combine well into a full mesh is all I'm looking for.

Wireless would be nice but isn't a dealbreaker. Need single line mode. Don't need the marker-less modes as they aren't accurate enough for what I do anyway. (but wouldn't complain if it was available). Don't need an all-in-one, but again, wouldn't complain (but out of my price range without sacrificing accuracy?)

Thanks!


r/3DScanning • • 2d ago

Revopoint MIRACO 2 (Kickstarter)

2 Upvotes

Hi Folks

There's a new kid on the block coming - Revopoint Miraco 2, portable all-in-one 3D scanner brings blue laser scanning , infrared structured light, and photogrammetric metrology, for scanning and editing untethered or connected to a PC.

Some Specs:

  • blue laser scanning: 34 crossed blue lines, 15 blue parallel laser lines and  single-line mode
  • near-infrared full-field
  • VCSEL structured light
  •  single-frame accuracy of up to 0.02 mm in multi-line laser mode
  •  Accuracy Up to 0.02 mm + 0.05 mm × L (m)
  • for small to BIG minimum scan size of 10 × 10 × 10 mm up to 5 × 5 × 5 m
  • 2 MP near-range RGB camera with a 50 MP RGB camera

Scanning up to 120 fps, indoor and outdoor (up to 100 000 Lux), some advanced AI software features like "Revo Agents" for simplified 3D workflows with automated point cloud fusion and Scan-to-CAD conversion. 3D Gaussian Splatting**.**

For further Information you can check their kickstarer camapaign with some big discounts (starting from  $1,425) you may be interested in ! https://revo.ink/4eqAKPB

I am doing some beta testing and will be sharing some scans along the way.

Here a scan of an old GPU backside with small transistors. Scanned with parallel laser line mode, fused at 0.15, meshed at 0.19mm, no scanning spray used.

Another scan of a guitar as a rather mid-sized object. Usually rather difficult to scan, very reflective high glossy black body with polished chrome parts, I could scan it easily without using a 3d scanning spray with laser mode ( 34 cross lines and 15 parallel lines, didn't use single line mode for this one ).

Fused at 0.3mm, meshed at 0.46mm.

What do you think?

Anything you would like me to scan?

Cheers


r/3DScanning • • 2d ago

Laser brightness is why your scans are noisy or full of holes — here's how to set it

1 Upvotes

Kept seeing posts about noise and missing surface data, and in most cases it traces back to one parameter: laser line brightness. Too high and the stripes overexpose (lost edges, heavy noise); too low and the signal is too weak to register (large gaps).

The workflow we use: turn on Real-time Exposure in 3D_Matrix before scanning. Laser lines show as purple (too dark), red (overexposed) or green (just right) — adjust until most lines are green, then turn it off and scan as usual.

If you want a head start instead of fine-tuning from zero: white/light/transparent/matte surfaces reflect more light, so start low, around 10%–30% (≈20%). Black/dark, light-absorbing surfaces return weak signals, so go high, around 70%–90% (≈80%).

One more thing: if edge detail or noise suddenly gets worse mid-scan, you probably moved to a different area of the object and forgot to readjust.

What settings do you start with on tricky materials?


r/3DScanning • • 2d ago

Scanner selection

3 Upvotes

I’m looking for a scanner and could use some help. I’m mostly planning to scan automotive parts including chassis/engine bays.

I’m a mechanical engineer and have spent some time in the past messing around with scanect and another early software that used an Intel sensor that I can’t recall the name of, both were toys at best, largely due to tracking and frame rate limitations.

At this point the technology seems to have cone a very long way with much lower cost, so I think I’m ready to pull the trigger on a scanner. I’m between a few options but open to other suggestions as well.

My laptop is fairly old so I’m planning to upgrade that as well. Priorities are reliability and usability, based on my previous experience if it’s frustrating to use I won’t use it.

Option 1) Einstar Vega
Available from einstar in used like new condition for $1k, this may be the cheapest option given the chance my laptop is up to the task of post processing.

Option 2) Creality Raptor
Obviously requires computer upgrade, but used machine that meets specs is ~$500 locally. Slightly higher total cost than Vega but tighter resolution and lower cost if Vega still needs a PC upgrade.

Option 3) Einstar Rockit
Based on reviews this seems like the “buy once cry once” option with the best odds of working as expected.

I’d love some feedback from someone with experience with one or more of these, I’m having some analysis paralysis over here. I don’t want to spend more money than needed for features I don’t need for my use case, but I’m terrified of burning a grand or more on something that doesn’t work as intended.


r/3DScanning • • 2d ago

How to model parts out of a scan

Thumbnail
gallery
11 Upvotes

I just got a new einstar 2 and it works wonderfully. But I'm having a bad time wrapping my head around actually modeling the parts I need.

I'm working on a cover for my car fusebox as my first project. I already have years of experience modeling basic stuff in fusion but never out of 3d scans and such complex shapes.

The first image is the scan and the second one is the result I got so far by using fusion's form. It took me several hours to get to this point and I'm not happy with the results. The part is all bent and doesn't fit perfectly yet.

I also tried to use the mesh section and then create a sketch out of the contour which got me to image 3

How would you takle this kind of project? Is there a better tool for this kind of work?


r/3DScanning • • 2d ago

REPORT METROLOGICI VELOCI: Crea il tuo Template STL vs STP

Thumbnail
youtube.com
1 Upvotes