r/Construction • • 14m ago

Humor 🤣 Fuck it

Thumbnail
gallery
2 Upvotes

On a walk this afternoon and found a fire hydrant where they just said fuck it, It’s already at the right height just pour around it. Second picture for reference on how it should look.


r/Construction • • 25m ago

Tools šŸ›  What kind of bag is this?

Post image
3 Upvotes

What do you all know this as? I’ve never heard an actual name for this style of bag outside of hearing an old timer refer to them as saddle bags. And who makes some nice ones?


r/Construction • • 3h ago

Informative 🧠 How to seal between two worm/rpe liners

1 Upvotes

Here is the photo of two liner between bog and pond area. The water is seeping into underneath the pond liner. How do I seal the area between that. Water can flow from bog, it can flow from rain or waterfall leakages

It’s too late to take out the liner. I am thinking to use any sealant to put in which is Epdm/RPE FRIENDLY and can fill the gaps in between


r/Construction • • 5h ago

Tools šŸ›  Hair protection

Post image
3 Upvotes

Does anyone have any recommendations for silk liners for hair protection from hardhats similar to this, i would be buying this one if it wasn’t sold out, I’ve gotten sick of hairline damage and damage in general from wearing a hardhat


r/Construction • • 5h ago

Picture Thanks for y'all's anchor advice. Got the project wrapped up last week.

Thumbnail
gallery
90 Upvotes

Fire treated lumber and high-impact rated drywall went into it. Did finishing work with red oak countertops and maple baseboards painted the same color as the lobby tile. Anchors less than every 2' into the ground with a SST post anchor on the short wall.


r/Construction • • 6h ago

Careers šŸ’µ Business majors, especially finance or information systems, do you have any regrets? Would you do something else now?

0 Upvotes

I’m planning on transferring to the University of Florida for either finance or information systems. I already like what they do, so my main goal is pay. My ultimate goal is to reach 150k after 8-10 years of experience, without working 60+ hrs every week, so no IB/PE. I know it’s not what most people earn, but I know it’s achievable. I’m also a bit worried about AI, so I’ve been thinking about construction management too. What do you recommend?
For reference, I’m 19, have a 4.0 GPA,
and work as a supervisor at a pharmacy


r/Construction • • 11h ago

Careers šŸ’µ Moving from Bid Management into Pre-Construction – is it a smart career move?

1 Upvotes

UK-Based Hey everyone, I made this account solely for the purpose of getting advice from all of you, so whatever thoughts you'd have would be greatly appreciated!!

(Sorry for the essay you're gonna read below🤣🤣)

I've been working in the Construction industry for two years and in Bids for a little over a year now. I'm currently working in bids and tender coordination, as an Assistant Bid Manager, with experience supporting the preparation and submission of PQQs, ITTs and wider tender documentation.

I'm considering an opportunity to move into a Pre-Construction Coordinator role and would really appreciate some insight from people working in pre-construction, particularly those with experience in both areas.

A few things I'd be interested to hear your thoughts on:

Career progression:

Given my existing experience in bids, would moving into pre-construction be a good way to broaden my industry knowledge and develop my career?

Or could it potentially take me away from a more traditional bid management pathway?

Role differences:

How would you describe the main differences between bid management and pre-construction?

Where do the responsibilities overlap, and what additional knowledge or skills does pre-construction require?

Future opportunities:

What career paths can opening up experience in pre-construction lead to?

Could it provide a route into roles such as Pre-Construction Manager, Estimator, Bid Manager or wider project/commercial management?

Technical and mathematical skills:

How much maths is involved in pre-construction on a day-to-day basis?

Is it generally basic calculations, measurements, quantities and cost-related spreadsheets, or does it involve more advanced mathematical/technical knowledge?

Ultimately, I'm trying to establish whether this would be a worthwhile move for someone with a background in bids who wants to develop a broader understanding of the construction industry and keep their future career options open.

I'd appreciate any honest advice, experiences or things you wish you'd known when starting out. Thanks!


r/Construction • • 12h ago

Picture Old foam can burst on a rainy day, finally got all the stains off this panel

Thumbnail
gallery
20 Upvotes

had two conduits going through a sandwich panel wall on a rainy day. grabbed an old can of spray foam to seal the penetrations and it suddenly burst out everywhere across the siding.

cured PU foam on grooved metal panels is a pain to get off without scratching the paint. took way longer than the actual conduit work, but finally got every trace off and put the caps on.

not naming the cleaner I used so it doesnt look like an ad.


r/Construction • • 16h ago

Other Electrician apprenticeship or Safety job while still in school for a bachelor’s in CM

4 Upvotes

Wassup guys. I basically have 3 and a half years left of my 4 year CM degree before I graduate. I’ve been looking to either start an apprenticeship as an electrician or get numerous certifications to start a safety job in construction while still in school. My girl and I just moved into a pretty nice apartment that costs some money so I was wondering if it’s worth it in the end to start an apprenticeship with the low amount of money that’s offered or to start with decent money working safety in construction. I’m in Georgia btw. Lmk what you guys think ! I would say I need to make at least $23 a hour but I’ve been seeing $17-$20 for apprenticeships. I’m about to turn 27 btw so I have grown man bills versus a teen or early 20 year old starting college.


r/Construction • • 18h ago

Other JCJ METAL FABRICATION AND CONSTRUCTION SERVICES

0 Upvotes

Hi po! Our home at Ovialand in San Pablo City, Laguna, was recently turned over, and we’re looking for a reliable contractor to build our fence and work on our kitchen.
Has anyone here hired JCJ METAL FABRICATION AND CONSTRUCTION SERVICES? We’ve spoken with them, but I haven’t found any photos of their completed kitchen projects with client reviews online. If you’ve worked with them, I’d appreciate hearing how it went. We already talked to a few contractors Theyve estimate of around ₱680,000 for the fence and kitchen, so we’d like to compare quotes. If you can recommend a contractor in San Pablo whom you’ve personally hired for similar work, please share their name, what they did for you, and roughly how much it cost, if you’re comfortable sharing.


r/Construction • • 23h ago

Video Concrete demolition with an ocean view — Carlsbad, California

190 Upvotes

A little footage from our beach access repair project in Carlsbad. The crew is breaking down the old reinforced concrete stairway supports, with the Pacific right behind them.

Hard work, but the view isn’t bad.

Edit:

The columns had to be brought down to a specified elevation. To prevent spalling, the crew removed the last few inches with handheld tools.


r/Construction • • 1d ago

Other Why do men spend so much time staring down holes

108 Upvotes

Ive worked on a bypass now for a few months, and above all I cannot understand the time men spend staring down holes which have been dug, it happens several times daily on various areas of the jobs with multiple teams involved.

Can anyone enlighten me? Previous to this I thought it only happened on beaches where there was a very keen interest to dig the holes


r/Construction • • 1d ago

Structural Big day today. Rebuilding my mother-in-law’s 12x16 deck as a surprise for her 70th birthday—looking for eyes on my plan & stringer landing ideas as I’m still fresh in the trade and learning

Thumbnail
gallery
7 Upvotes

NEED ADVICE ASAP - Fresh in the trades attempting a 70th Birthday Surprise 12x16 Deck Rebuild For Mother In Law—Tell Me If My Plan Sounds on point or feel free to drop some advice or tips. I’m fresh in the carpentry trade and have spent a lot of time learning and reading as well. This is my second deck project. I have it stripped down and the excavator is here so There’s no turning back now šŸ˜‚

So I am Kicking off the rest of this ā€œBIGā€ to me project today while my mother-in-law is out of town ahead of a surprise party next week for her 70th birthday. The deck is in rough shape and needs code upgrades, so I’m tackling it as a surprise to save her a big bill. This is only my second time doing this kind of deck work alone as I’m very fresh in the trades but consider myself handy and willing to learn, I’m trying to do everything by the book without cutting corners and keeping safety as my number one priority.

Previous build context:
I previously added stairs to a small cantilever deck behind my detached garage (originally a step-out landing, set up as a secondary exit), adding supports and concrete piers to handle the extra load.
Digging down on that first job was rough—especially pouring a formed concrete landing pad that took around 40–80 lb bags of cement and a big mixer, almost more work than the stairs themselves. Dropping threaded rod into Sonotubes for post standoff plates worked well for me there. In hindsight I should have used 6x6s on that project as well but now I’ve learned and will do so especially as it’s code and this is a way bigger deck and not cantilevered.

Current state & tear-down:
Stripped the deck down to bare framing; joists are solid with no rot, and I’ve pulled 1,000+ nails.
Currently has 3 bouncy stringers nailed in from the back with no brackets and resting directly on dirt—swapping to 4 stringers with Simpson ZMAX Strong-Tie connectors.
Replacing direct-buried 4x4 posts with 6x6 posts sitting on concrete piers to bring it up to code.

Materials & fasteners:
Joists: Joist tape over the clean joists.
Fasteners: 2-1/2" #9 GRK all-purpose screws and 1-1/2" Strong-Drive SD screws for stringer brackets/clips, L-brackets connecting 6x6 posts under the deck, and post hardware at the bottom piers.
Stairs: Keeping the existing 7" rise / 10" run (code-compliant and comfortable), cutting 4 new stringers out of 2x12x16s.

Today’s plan & timeline:
Pull the old stringers to drop weight, then shore up the deck \\\\\\\~2 ft back from the front edge using 2x6 ledgers top/bottom with 5–6 vertical 2x4 studs so I have clearance to dig.
Planning to tie a rope to the front framing and keep light upward tension with the mini excavator bucket as a backup safety measure while shoring is in place.
Using a mini excavator instead of an auger because of all the rocks in the yard (I dug \\\\\\\~3.5 ft on old posts a few years back and didn't hit concrete, though I wouldn't be surprised if some is down there).
Digging 4 ft deep for footers with crushed stone in the bottom, covering holes until concrete arrives early next week, and setting post standoff plates with threaded rod dropped into Sonotubes.

Landing pad: Instead of pouring another massive formed slab with 40+ bags and a big mixer like my last stair landing, I’m looking at a 300–500 lb stone (like bluestone) set on crushed stone/gravel and use the excavator to move it and place it even with the ground so it doesn’t throw off the 7" rise / 10" run layout. That will make it easy for me to just make a new set of 4 stringers instead of 3 and follow the same rise and run on the 2x12x16s I got. A small-load concrete truck will pour the Sonotubes next week and make my life easier.

Looking for feedback:
Does my shoring, pier, and excavator-backup plan make sense, or am I missing anything?
Any recommendations on the best stone to set stringers on? Any other tips , tricks extra things I should consider? Do you think I should dig down an extra cement pier behind the stairs and add mid span support? It’s 10 stairs and never had one prior. I did add one on my other set of stairs I did but those were a much longer span.

Starting the day now—I’ll post an update tonight with how it goes. Appreciate any advice as I’ve gotten a lot of good help from this page in the past and if my mother-in-law bought a Ford to pay a professional to do what she would do it in a heartbeat, but it’s not in her budget. So the next best option that I had was for me to do it. She’s been a good mother-in-law, so she deserves it. I take pride in trying to do things the right way, and my most important thing is making sure that everything is safe. Although this is not my trade, I do consider myself pretty handy. and willing to learn. I feel by fixing this for her, it’s better than leaving it in the current condition where it was rotted posts, rotted boards up top, etc, with no way to get it fixed.

Since I also couldn’t afford to pay to have it fixed for her, all I could offer was my labor for free. In the end, this has cost about $3000 out of pocket for all materials and rentals, and I think it’ll be a big upgrade from what it was and a lot safer as many deck boards where getting so thin your foot could go threw it and the 4x4s would sway a bit as well as the stringers were bouncy and starting to pull off the rim joist since there’s no brackets. I hope to surprise her on her 70th birthday when she gets back in town and have it all finished up by next week.

Ps - pictures at the end is of the deck I fixed up at my house. If I was to do it again, I would not use those plastic post holders and I would tie everything indirectly to the framing much stronger that way but still learning. Also, the propane tanks have been removed, as I installed that mini split. It was a cantilevered deck prior, but with me adding the stairs, I felt that added a lot of weight, so I added the two support posts, now that I’m doing this deck and I’ve learned a little bit more, I’m doing the support post in 6 x 6s like I should’ve done on that one. definitely a learning process. I will probably go back and switch them to 6 x 6s at some point soon even know everything is solid on that one - took me the most time to do the landing pad and learn how to measure and cut stringers for my first time.


r/Construction • • 1d ago

Structural Why do framers insist on making field adjustments instead of simply following directions?

0 Upvotes

I’m a junior structural designer doing a site walk on a residential build, and I noticed the lead carpenter was shimming a header and slightly altering a rough opening by about 3/16". When I brought up that the stamped drawings specify exact dimensions down to the 1/16th, he just laughed and told me "wood isn't steel, kid."

I spent nearly 40 hours ensuring the load paths and tolerances in Revit were mathematically seamless. If the guys in the field are just going to eyeball things and use shims anyway, what is the point of precision engineering? Is this normal or should I flag this to the GC?


r/Construction • • 1d ago

Informative 🧠 How does telecom sign-off work for a new building in your country?

Thumbnail gallery
4 Upvotes

r/Construction • • 1d ago

Picture Why did the painters have a big can of Grand Ma Brown's baked beans?

Thumbnail
gallery
69 Upvotes

r/Construction • • 1d ago

Careers šŸ’µ Looking for an career change

0 Upvotes

M19 and I have an interest in doing heavy equipment I have no cdl but my pops always told me the right company will pay for you to get it. I have experience doing cell towers I don’t wanna do it for the rest of my life. I live in South Carolina and I have a reliable pickup truck I’ll go anywhere to start this career any advice for to start?


r/Construction • • 1d ago

Picture The city redid sidewalk corners and somehow managed to install an itch in my brain that I can’t scratch.

Post image
48 Upvotes

r/Construction • • 1d ago

Safety ⛑ Good looking quality safety glasses?

3 Upvotes

Anyone have good recs for quality safety glasses? I had a pair of heatwaves and they were great but I lost them. Can anyone second heatwave if I should try out another frame look? Or any other good brands that don’t just look like the typical safety glasses


r/Construction • • 1d ago

Humor 🤣 Do you think Jesus was told to find the beam stretcher in his early apprenticeship?

184 Upvotes

r/Construction • • 1d ago

Informative 🧠 Blue-collar guys: What kind of underwear are y'all wearing on long shifts, and what do you recommend?

39 Upvotes

For the guys working physical, blue-collar jobs (construction, warehouses, kitchens, mechanics, etc.)—what kind of underwear are you running with, and what brands/styles do you actually recommend?

​Between constant moving, sweating, bending, and grinding through long shifts, cheap pairs ride up, bunch, or wear out way too fast. Looking for something that actually breathes, stays put, and holds up over time without breaking the bank.

​Are y'all sticking with standard cotton briefs, boxer briefs, moisture-wicking athletic stuff, or specific brands like Duluth, Saxx, ExOfficio, Hanes, etc.? Drop your go-to recommendations and what works best for you.


r/Construction • • 1d ago

Other I’m heading back to rebar and I’m scared

9 Upvotes

I always liked doing rebar when I started, I mean I had my bad days where things got to me and there’s always assholes or idiots. I’m just worried cause I’m going back after such a long break I did like a 1.5-2 years already put off getting my blue book and quit cause of stomach issues and annoyance at coworkers. I’m going back now cause kitchen work just isn’t paying enough I’m worried about how to handle the stress. I have to bus to and from work now and it’s winter and I enjoy most the people I’ve worked with it’s just those days their hating the new apprentice or some guy snaps at me when I don’t go from setting something down to immediately tying. It’s just a frustrating line of work when people are constantly rude to you, like when I did consistently work for my company I did good and kept my head down and listened but the more people demean you because of the simplest thing it grinds my gears, like when we were about 15-25 feet up and I was working on a ledge with no fence ā€œwhich is illegalā€ I had to tie the edge bar but me being afraid of heights and there being no safety railing I tied a zigzag of the edge bar and the bar next to it so as to not be near the edge. Well my asshole pencil dick of a foreman who’s kicked his own stepdad and stepbrother of of a site for calling his assholeness out, he comes over to me goes ā€œdidn’t I tell you to tie that fucking barā€ and I go ā€œI’m ty my both there’s no safety railingā€ he goes ā€œI don’t care tie the bar I told you. Later that night the actual boss of the company told us we Should’ve refused to work because of the lack of safety railing that high up, what a bunch of idiot dicks. Only reason I’m going back is cause I have no ged and kitchen work is fucking pathetic in pay.


r/Construction • • 1d ago

Careers šŸ’µ Those of you that work in the trades in unconventional fields; what do you do and do you enjoy it?

40 Upvotes

I've always been fascinated in the blue collar professions that are sort of out there. Carpenters that do set design for movies/TV, lighting riggers, stuff like that. I met a guy once at a bar that said he was a welder that worked for WWE (F at the time) building their stages and ramps and shit for special events and I thought that was super interesting. Not construction, but my dad was a mechanic and worked on several ProAm drag car teams over the years where he got paid but not enough to make a living for a family of 4.

Any of you work in an unconventional field?