r/EngineBuilding • • 10h ago

Rotating assembly is balanced, starting reassembly with fully forged bottom end.

Post image
66 Upvotes

r/EngineBuilding • • 11h ago

Help with cam shaft

3 Upvotes

So i am getting my twin turbo big block chevy engine for my jet boat rebuilt because I had a cracked piston and cracked heads. I am using a mechanic that was recommended to me by a ton of people but im having a small issue with the cam shaft he chose for the build.

The engine is a 496 bbc with a gale banks twin turbo setup on it. Its got 360cc flotek aluminum heads, SRP flat top forged pistons, H beam rods, stainless steel valves, and more.

The engine builder chose a clay smith custom grinded hydraulic roller cam shaft for it and here are the specs:

Intake duration: 316 degrees(advertised)/ 259 degrees(at .050”)

Exhaust duration: 317 degrees(advertised)/ 263 degrees(at .050”)

Lobe separation angle: 110 degrees

Centerline timing events: 107 degrees intake/ 113 degrees exhaust

Intake valve events (.050”): opens at 22.5 degrees/ closes at 56.5 degrees

Will this camshaft work for my twin turbo setup? Is there going to be too much overlap? This gale banks turbo setup doesnt produce a ton of boost but it should be around 15 pounds. Im hoping for around 800-1000 horsepower on the dyno once its built.

Thanks


r/EngineBuilding • • 14h ago

5.3L v8 2010 1500 Sierra crew cab GM 4th gen with the damn AFM. Not yet deleted. How do I mod this

1 Upvotes

I just inherited a free truck. It is in a very well maintained condition. Run very smooth. It does still use the AFM. I noticed while driving Highway it toggle from INST ECON V8/V4
After I delete this bullshit, where do I go. I don’t know much outside of blinker fluids.


r/EngineBuilding • • 15h ago

C4 transmission (bar?)

Post image
50 Upvotes

Ok, I know it’s not an engine, but it’s in the family? Lol.

I know this bar circled in red does not go there and I assume the previous owner put it on there to hold the TC while being stored…. My question is, is this a bracket or part to a classic Mustang? Does anyone know what it really is?


r/EngineBuilding • • 20h ago

Ford Ford FE (Probably 390) 2100v carb setup help

Thumbnail
gallery
4 Upvotes

Got a funky 1967 thunderbird with an unknown FE engine with a basically junk 2v carb and a 1968 truck intake. Guy who sold it claimed 429 (obviously isn’t) but honestly thought it was a 429 for some reason (Good dude, still helping me out with it ). Cars frame and most of the body is rot free and it’s a perfect project. I’m having issues figuring out the hookups on the carb due to how the guy before me handled everything (cut first, label never). I have a manual but it has been very little help as it seems to assume things would be setup in a stock position, not being put back together from a pile of parts in the trunk of the car. The photos show my attempt at the throttle linkage, and have parts/tubing circled that I am confused on where it goes or what’s missing from it. The final photo shows the top plate ?linkage? that for some reason does not open the top plate when opening the throttle body up. I am wondering if anyone has helpful diagrams or information on any of these components. Also information on where the vacuum lines on these hook up.


r/EngineBuilding • • 23h ago

Valve stem tip broke off – Chevy 355 SBC

Thumbnail
gallery
26 Upvotes

About 3 mm of a valve stem tip broke off on my rebuilt 355 SBC.
L31 Vortec heads and original valves, Summit SUM-K00042 cam kit, SUM-141700PL roller-tip rockers, and stock pushrods.
The engine completed its 20-minute cam break-in. Rocker contact patterns look centered.
Any ideas what could cause this? Wrong geometry, valve springs, or a defective valve?


r/EngineBuilding • • 1d ago

Very high idle surge 2014 silverado 1500 l83 stage 2

3 Upvotes

2014 Silverado stage 2 LL cam, l83/5.3 1500, 6l80

Yup im back again.

I installed the new cam and had an idle surge, i assumed it was the base tune but then I sent it to get tuned and it still isnt working. They tuned it, said nothing about it and then I asked if I had a vacuum leak and they said oh yeah, but the tune will be good once you fix that. I drove it home and it runs fine but pulls at stop lights as the idle rises from around 750 to 1250 rpm every couple of seconds, I sprayed brake cleaner all over the engine bay multiple times on the hoses and got nothing.

Any questions please ask ill try to respond to all of them. Any advice is appreciated.


r/EngineBuilding • • 1d ago

Chevy New Heads and Decked Block Equal… Stock Length Pushrods?

48 Upvotes

Hi all, first time building an engine and I have a flat tappet SBC 350 with new Flotek 102-505FT heads, 0.041” compressed thickness head gasket, and block decked for 0.010” clearance. Heads stated that pushrods would need to be sized up +0.100” from stock (~7.800”). I set up two valves to my new measure pushrod length using the Comp Cams 7703-1 checker tool, which has an advertised minimum length of 7.800” and when I measured it with a ruler, got between 7.8125” and 7.84375”. When I was using the tool, I found that the minimum length of the tool seems like a pretty good pushrod length, but I am surprised it’s not too short considering my setup. See the video to look at the roller contact with the valve stem and the two links to see the exhaust and intake markings it made… looks good to me, but want to be sure before I order some stock length pushrods.

Exhaust -> https://ibb.co/zhvw4QCL
Intake -> https://ibb.co/hxsNxVSd

Thanks!


r/EngineBuilding • • 1d ago

Is this piston fucked?

Thumbnail
gallery
13 Upvotes

It’s hit something while it’s been out of the block. The edge is raised. Is it junk or can I file it down carefully?


r/EngineBuilding • • 2d ago

First full rebuild on my 4.6

3 Upvotes

Its a Romeo modular 4.6 sitting inside a 97 mustang, I've gotten the wiring harness disconnected and am going to pull the motor when the weather clears up a bit more. I'm planning on using this rebuild as my chance to do all the internals I've been planning on such as pistons cams headers a wet nitrous kit (50 shot) and a tune. I'll be calling a few machine shops in my area to inspect the block when it gets torn down to make sure its work rebuilding with the old block and connecting rods. I'll be installing hypereutectic pistons as they come with the rebuild kit from rock auto, 268H camshafts from modular head shop with 210 lb valve springs and shorty headers. im expecting to spend about $3600 in parts and shipping and was hoping for any tips on building my motor or getting it tuned somewhere as I'm unsure of how to go about a first start with aftermarket camshafts.


r/EngineBuilding • • 2d ago

How a Gasoline Engine Works 4 Stroke Cycle, Valves & Camshaft Animated C...

Thumbnail
youtube.com
0 Upvotes

A clear cutaway animation of a four-cylinder gasoline engine: intake, compression, power and exhaust, plus the valves, the camshaft and the firing order.

8

 

9

0:00 Parts of the engine

10

0:25 The four strokes

11

1:07 The camshaft and valves

12

1:31 Four cylinders working together

13

 

14

Note: the drawing shows four cross-sections of one engine, side by side, and is simplified for clarity. Real engines vary (for example, direct-injection engines add the fuel inside the cylinder).

15

Narration: AI-generated voice.

16

 

17

#engine #howitworks #mechanics

Voiceover generated by TTSMaker (https://ttsmaker.com)


r/EngineBuilding • • 2d ago

Is my block toast?

Thumbnail
gallery
256 Upvotes

Was removing paint on my 351 Windsor block noticed this is it toast? I blew air into it to try and see if air would go through. I couldn’t feel any. What do I do?

Engine was running when pulled was just gonna do a refresh rebuild


r/EngineBuilding • • 2d ago

Bolt hole spacing on Edelbrock 2116 Vortec intake manifold – TH350 kickdown bracket

1 Upvotes

Hey everyone,
I’m running a Chevy 350 SBC with Vortec heads, an Edelbrock 2116 intake manifold, an Edelbrock 1406 carburetor, and a TH350 transmission.
I’m trying to reuse my old TH350 kickdown cable bracket, which was mounted to the intake manifold.
Does anyone know the exact center-to-center distance between the two rear intake manifold mounting bolts on the driver’s side of a Vortec intake manifold?
I’m considering modifying my existing bracket instead of buying the Edelbrock 8032 bracket.
I’d love to measure it myself, but unfortunately my engine block is currently at a welding shop getting some freeze cracks repaired, so I can’t take any measurements right now.
If anyone has measured this distance or has an Edelbrock 2116 they could measure, I’d really appreciate it!
Thanks in advance!


r/EngineBuilding • • 2d ago

Lookong for some guidance on budget carbureed vortec build

6 Upvotes

I'm wanting a new engine for my 1986 El Camino and after a bunch of research I decided that a 5.7l vortec engine might be a pretty good idea cause they're really cheap and not that bad out of the box (or van/Tahoe in my case). Issue is I'm really new to all of this and I don't know where to start and there's not a ton of budget builds for me to follow along to.

All that said here's what I'm wanting: I'm wanting to do some basic work to get it working in my car and leaving room for upgrades later one. Like I want to put a cam in it, new intake and a carb. Then drop it in.

400 hp at the crank somewhere down the line but not right away

Maybe nitrous

Here's what I have:

A 1986 El Camino with a 305 engine

A 200-4r transmission which will need to be rebuilt and upgraded later on

Plans to go to 3.73 posi gears (shopping around now actually)

Pretty limited knowledge and experience with engine work, but I gotta start somewhere

Thanks in advance everyone


r/EngineBuilding • • 3d ago

Can someone help me ID this engine?

Thumbnail
gallery
14 Upvotes

It’s in a pile of junk in the back of a barn on a property that I recently purchased. It looks unique and I hate to scrap it.


r/EngineBuilding • • 3d ago

Pistons ruined?

Thumbnail
gallery
176 Upvotes

My number three piston, I noticed had these two gouges most likely from whoever rebuild this engine last the heads and the valves have zero damage, and there is no burr above the surface of the piston. Are they reusable or do I need new pistons?


r/EngineBuilding • • 3d ago

Does this look bad?

Thumbnail
gallery
14 Upvotes

1.9 TDI AHF


r/EngineBuilding • • 3d ago

Need help Identifying this Cylinder Head!

Thumbnail
gallery
0 Upvotes

I can't match this head to any of the catalogs I own. Initial thoughts are a Mitsubishi or Mazda but can't narrow it down to a year/specific models. Any help would be appreciated!

Solved! Seems to be a 1988-92 Isuzu Stylus 4XE1 1.6L Cylinder Head. Thanks for the help everyone!


r/EngineBuilding • • 3d ago

Chrysler/Mopar Another "What's that noise" post - need someone smarter than me

5 Upvotes

Hey all,

The video above is my 2002 Dodge Neon I'm supposed to go to the track with in two days. The car has 32k miles, but it's also a former SCCA car. It's spry, but it's also lived hard on occasion.

Bought it knowing it had a "tick" and an original belt when I bought it, did a bunch of work (including new rockers) right after I got it (literally within 5 miles). On startup again, I noticed the tick sounded more like a bottom end noise in my uneducated opinion and seemed to become fully audible around 5 min of idling, but neons are notoriously rattly.

Drove the car 300 miles and drained oil/cut filter last week to find a good amount of non-ferrous. After removing the valve cover, it became apparent multiple new rockers were defective. Roller bearings were dumping aluminum into the motor.

Swapped back in the old ones (which looked totally fine) and the motor got noticeably quieter...but once the oil gets some heat in it, that bottom end noise returned.

Dropped the pan and pulled the rod caps. Nothing visibly concerning and no play. Reassembled with original bearings, lube and everything as it came out (in theory - a perpetual self-doubter, kept waking up last night thinking I had to have done something wrong).

Start the car up, whisper quiet. Nice.

5 min into idling, I have the video you see above. Same noise, same rhythm - makes sense, I literally took it apart and put it back together with everything the same minus the rod bolts.

I have to go out and drive it today and see if it gets worse (indicating I screwed something up during reinstall) but it seems to be same volume/location. Plan was to change the oil one more time and go for it, assuming the next change isn't complete glitter from me damaging the bearings on install.

What the fuck is this? Logic says it wouldn't be piston slap, because it starts when warm. Even if it's rod bearings now courtesy of yours truly, it wasn't when I opened the motor up. Maybe something in the head?


r/EngineBuilding • • 4d ago

Can i run an Oval port intake on a gen 5 454 with the peanut port heads?

4 Upvotes

Gonna carb swap a gen 5 for my project, not gonna fully build it but i was wondering if i could get away with a bit of a missmatch on the shape since I had heard it didnt mean to much.


r/EngineBuilding • • 4d ago

Questions on bearings/piston

Thumbnail
gallery
11 Upvotes

Long time lurker: Been taking apart my engine (Alfa Romeo 2L Nord) for unrelated work. What do you guys think of the bearing and piston? My main concern are the two areas showing copper. My current plan is to send it for another year and do a full rebuild next winter as I‘ve got already plenty of work scheduled for this winter.
Thanks for your insights!

EDIT: Thanks everyone for your input, helped a lot!


r/EngineBuilding • • 4d ago

Chevy Main Bearings

Thumbnail
gallery
22 Upvotes

These are new main bearings, I did not install them not sure what is on them but you can feel a texture difference in them, would you run these???


r/EngineBuilding • • 4d ago

Normal or abnormal wear?

Thumbnail
gallery
29 Upvotes

Had a 327 rebuilt recently. Had the crank ground, new crank bearings, roller cam and lifters. Decided to go with a more aggressive cam and noticed some wear on the roller lifters, cam and also the main bearings. The motor only has about 1000 miles on it and there’s no metal in the pan. Think it’s safe to re use the lifters? Should these crank bearings be replaced?


r/EngineBuilding • • 4d ago

Normal cam wear or my engine gonna blow m57tu2

Post image
5 Upvotes

2012 X5d with 133k miles no issues no metal in oil and just happened to do valve cover and saw this and its smooth with finger, most of them have the same mark