r/FiestaST • u/DaYearZeroHero • 16h ago
MK7 New Wheel and tire set-up!
Finally got the new set-up! Konig Heliograms 16x8 with Continental ECS02's 205 45 R16! Couldn't be happier with the fitment! And the grip is a chef's kiss!
r/FiestaST • u/DaYearZeroHero • 16h ago
Finally got the new set-up! Konig Heliograms 16x8 with Continental ECS02's 205 45 R16! Couldn't be happier with the fitment! And the grip is a chef's kiss!
r/FiestaST • u/Whitrzac • 21h ago
Picked up this 2016 for cheap with hail damage. 160k, no record of the tb being done and a lot of other maint that hadent been done.
Started buying parts from the get go to do everything.
Tb/wp, gates kit
Serpentine belt+tensioner, gates kit
180* thermostat, gates kit
Intake manifold gasket, felpro
Throttle gasket, felpro
Valve cover gasket, felpro
Noise maker delete, whoosh
Trans side shift bushings, whoosh
Trans oil, motul dctf
Plugs, ngk 1 step colder
Watched a few videos and glanced over the service manual, but havent worked on the 1.6 before.
The 10pc dp tool kit includes everything you need, dont buy the 18pc
You need 2x m10 x1.5 flange nuts to hold the flywheel locking plate in place.
7mm( hose clamps)
8mm(most)
10mm(intake manifold/starter)
13mm(most larger hardware)
15mm(alt mounting)
17mm(fuel line)
18mm(crank bolt)
19mm(motor mount)
E torx 6(alt stud)
I took apart way more than was needed for just the tb/wp because of the other work I was doing.
I took out the battery box to get to the shifter bushings as well.
Idk why this myth keeps getting repeated, but you do not need to pull the axle to get to the tdc pin
Remove 2x 13mm nuts on the strap, 2x 13mm bolts on the mount come out. Wrench on the 3rd slotted one and the entire thing slides out of the way
Use the starter bolts+m10 nuts to hold the locking plate. Put the bolts in backwards from normal to avoid dropping the nuts in the belhousing.
Ac compressor needs to be loosened to get the thermostat housing off. Terrible design.
Intake manifold is easy enough to remove, not sure I would fight with the starter with it in place, especially after the alt is removed.
Alt mounting stud needs to come out/in with the alt. Theres not enough room to slide it on.
All of the electrical connections are fairly self explanatory and only fit one way.
Its a good opportunity to walnut blast the valves as everything is apart. Hobofreight blaster+fine media is $65. I extended the nozzle with some poly tubing.
Valvcover was leaking for quite awhile. Went through about 5 cans of brakeclean
Belt had 1 outside crack and most of the teeth on the inside. Probably good for 200k, but not worth the risk.
My trans took 2 full qts with nothing dripping out. Front end was lifted however. Shifts way nicer with fresh fluid and solid bushings.
r/FiestaST • u/spooky_diplomat • 23h ago
So I don't often post here, I own a fiesta ST it's a 2018 mag Gray, I frequently lurk and I like a lot of the posts but for the most part I'm just an observer here. I was overcome with the need to post today however, so a couple of months ago my transmission was weird and it was getting hard to shift into first and second gear and then it progressively got worse and worse to the point where it was almost impossible to get into first gear second was rough third was rough and sometimes fourth was rough. After doing lots of research on the forum and here on the subreddit it was suggested to get BG super synchro 2 fluid and do a transmission fluid change. Well when I took the drain plug out literally no fluid came out of my transmission. I even jacked up the passenger side of the car higher than the driver side to see if I can get anything to come out, and it was bone dry. The last time anybody worked on the car was when I had it in the shop for the slave cylinder change at about 70,000 miles, and I'm at 109,000 mi now. I also had my timing belt changed at like 93,000 mi, in which they would have had to take one of the axles out but I don't necessarily know if they would have drained all the fluid out then. So several thousand miles with no transmission fluid, filled it up today drives like a dream again, and I don't think I had any adverse damage to my transmission for driving it so long with no fluid in it.
Tldr these transmission are bulletproof.
r/FiestaST • u/Dry-Suit5785 • 16h ago
When I bought my 2015 ST, the guy I got it from said something about an eco mode that is somehow set through the steering wheel controls? He showed me once when I bought the car but it’s been a couple months and I’m just now thinking about it. He said if the throttle ever feels slow or something to that effect it’s in eco mode, and I have to do some combination of button pressing on the steering wheel to get it out of it? I’m sorry if it sounds confusing but I figured I’d ask if that’s a that a thing? Google showed no results for it.
r/FiestaST • u/DerDeutscheRLPro • 11h ago
Engine is warm
Just bought me a st.
It's 2013 and has 200000 km on it.
Everything seems good and the owner did oil change and service every 10k km.
Is this normal sound or is it ticking too much?
r/FiestaST • u/Alternative_Horse757 • 22h ago
I’m looking at a 16 st with 104k I was told it’s stock no mods and I come to look at it today I see it has after market mods
I suspect someone changed it to e85 at some point just bc of the the dizzy tuning reader
What do yall think?