r/FixMyPrint • • 21h ago

Fix My Print A2l es normal este ruido?

1 Upvotes

r/FixMyPrint • • 15h ago

FDM A2l

0 Upvotes

r/FixMyPrint • • 17h ago

Fix My Print Wtf happened here. First attempt at tpu gf

Thumbnail
gallery
2 Upvotes

Qidi q2

Qidi tpu gf

Speed 6mms^3

240°c

Flow 96%

Retraction 0.2

0.6mm nozzle

Layer height 0.3

Pa 0.045

It's highly unlikely it's a partially clogged nozzle as I used a 0.6mm. 0.4 tends to clog on composites. There almost zero stringing. But as you can see at the front and the left side I the back corners have craters. Before anyone says wet fillament I had this in a heated drug box then I printed from my qidi box which has dessicant pack at 15% humidity since it's actually stiff enough because of the fjberglass. In fact the main issues you will have with tpu are 95a and softer with the most common being 95a 85a and 68d.they don't feed.

Edit i just found out I entered my Pa wrong. I thought it was 0.045. it was at 0.45. It was off by a factor of 10


r/FixMyPrint • • 23h ago

Fix My Print Is this noise normal?

2 Upvotes

i have an creality hi combo, i dont know if the noise is coming from the nozzle touching the print or the building plate moving sound?


r/FixMyPrint • • 11h ago

Fix My Print Why did my model get this artifacts?

Post image
0 Upvotes

r/FixMyPrint • • 19h ago

Fix My Print Help with calibrating calibrating my Ender 3 v2 (yet again) - flowrate

1 Upvotes

Hey there. I am calibrating flowrate at the moment.

When I print the Calibration model from OrcaSlicer, i run into the problem that my filament feeder seems to get hickups at around 14mm height. I turned it off, since I didnt want to damage the motor.

This surely is not related to flow speed right?

The original model is 32mm high. I can't believe 14mm is the maximum already (that would be a flow of 12 basically).

In other words: I would understand, if my printer gets defects above 12mm, but my stepper motor making sounds and swinging back (like a hicup) like it's jamming does not sound correct to me, right?

Any clues?

Thank you!

EDIT: OrcaSlicer Overture Gold PLA Bed temp 55C Nozzle temp 220 first layer 200 afterwards --> 200 was best from the temp calibration before this step


r/FixMyPrint • • 22h ago

FDM Bambulab A2L

0 Upvotes

I can’t find any poop bins for my bambulab A2l. Does someone have a design/3mf?


r/FixMyPrint • • 14h ago

Fix My Print Unusable Z-Banding on Bambu X2D

Post image
3 Upvotes

I've tried different speeds, different filaments, etc. I've had a few months of good prints but it's changed suddenly. Oddly, it will sometimes randomly print without major issues but that's the exception. I'm at my wit's end here.


r/FixMyPrint • • 18h ago

Fix My Print Porque salen tan mal las letras??

Thumbnail
gallery
0 Upvotes

r/FixMyPrint • • 12h ago

Discussion Cloned objects have different top layer... why?

Post image
4 Upvotes

This doesn't need a fix, but I am super curious. One object was cloned six times. When I went to slice it, the final layer does not cover the full surface for four of the seven objects. I noticed the coverage ending lines up with the seam, but why is it doing that on only some of the objects when they are all identical clones?

If it matters, I'm using OrcaSlicer with my Flashforge AD5M. Thank you.


r/FixMyPrint • • 17h ago

Troubleshooting WHY is this edge curling at the same spot every time?

Thumbnail
gallery
26 Upvotes

Hello everyone. Im a bit desperate at this point I have to admit. I want to print this specific poop bin but it failed spectaculary the first time, as you can see in the second picture. Since then I calibrated my filament and tweaked some settings that might be the reason. The second print started curling again. And I dont know why. Its always also this one edge on the exact same height of the print.

Stats:

PLA

Nozzle 210

Bed 50 (BIQU Glacier)

Part Fan 100%

Auxiliary Fans 70-80% (with printed diffusors)

So yeah. I dont know what to do. Never had this happen before. Can anyone help?


r/FixMyPrint • • 46m ago

Troubleshooting Need help with overhangs

Thumbnail gallery
3 Upvotes

I tried different temperatures and speed, but there is no good result. What else i can do to make them better? Printed with Bambu Lab Pla Matte


r/FixMyPrint • • 3h ago

Fix My Print What causes this

Post image
3 Upvotes

Hi, im using bambu x2d default profile of 0.2 quality, the material is pla .

Just wanted to know what causes this


r/FixMyPrint • • 9h ago

Troubleshooting Z Offset issues (Anycubic Kobra S1)

Post image
2 Upvotes

r/FixMyPrint • • 12h ago

Troubleshooting Small holes on the edges

Post image
3 Upvotes

How do i remove these small holes on my prints? I have already did Pass 1 flow rate calibration and temp calibration. but these holes are very annoying. When i changed flow rate from 0.9975 to 1.00 it removed it but had some minor overextrusion

Printer: Sparkx i7

Filament: Polymaker Panchroma Matte Forest Green, dried 50C at 8H


r/FixMyPrint • • 12h ago

Fix My Print Need help with correcting my print.

Thumbnail
gallery
3 Upvotes

I am a newbie to using a 3D printer. I have an Bambu lab A1 mini. I have tried a few prints but they all have had issues. I am hoping someone can offer some advice on how to correct my issue. I am submitting two images of m issue. I’m hoping someone can help me with this matter.

Thank you


r/FixMyPrint • • 14h ago

Print Fixed Parts of large print finish rough

Thumbnail
gallery
2 Upvotes

I keep getting parts of the print finishing rough not sure why.

Bambu lab P2S
0.4 hardened nozzle
Bambu lab PLA basic black
Print as is from makerworld https://makerworld.com/models/3052229?appSharePlatform=copy

Cool plate super tack (cleaned before print)

Is it over extruding? Have calibrated etc


r/FixMyPrint • • 18h ago

Fix My Print ABS printing issue with Carbon Centauri 2

Thumbnail
gallery
2 Upvotes

Hi I'm new to 3d printing and I wanted to try to print in ABS. However I got a consistent issue I don't know how to fix. Note that the brim on the successful part of the print is difficult to separate.
From what I can tell may be a bed leveling problem, but I tried auto bed leveling and wanted a second opinion before I try to do it manually.

The print in the images is a max flowrate/max volumetric speed test - first one was not moved from the bed.

Printer is Elegoo Carbon Centauri 2 Combo.
The slicer is OrcaSlicer.
Filament is JAYO ABS black + white
Settings are in the images
Unfortunately I can't record a timelapse as it doesn't save.

Things I tried:
- adjusting the settings including: bed, chamber nozzle temperature, as well ass slowing down first layer,
- calibration on printer: auto bed leveling, PID tuning,
- temperature callibration in orca
- I taped all the little holes and gaps with insulation tape. The waste hole I covered with a plastic bag so it still has a way to drop poop.


r/FixMyPrint • • 19h ago

Fix My Print From previously post, I’ve been fixing problems only for new problems to appear

Thumbnail
gallery
3 Upvotes

On first picture there was this mess on top layer of the print and on right I changed the settings and it fixed some problems but it is sill an issue, so I’m not sure what I’m doing wrong
(I might give up using PLA I’m using since it’s run out)
Printer: Ender 3 V3 SE
Slicer: Creality print
Filament: PLA
Nozzle temperature 210°C
Bed temp: 60
Flow ratio 0.95
Top surface flow 1.00
Top surface line width 0.35 mm
Top surface speed 35 mm/s
Top shell layers 6
Solid infill line width 42mm
Infill wall overlap 10%
Only one wall on top surface: Disabled


r/FixMyPrint • • 19h ago

Fix My Print Lines on top of holes or supports

Post image
3 Upvotes

Hi

I have a flashforge 5m with the diy enclosure, just finished playing ocarina of time and wanted to to try printing an ocarina. It came out fairly well, but every time theres the top part of a hole or support interface i get this lines, its a mix between over extrusion and other under.

I printed at 0.12mm layer line, 205C with fan at 100%. I have already calibrated with orca slicer tools, but this still happened, has happened on other prints as well.

Are there ways to reduce or eliminate this? Was using basically stock 0.12mm profile.


r/FixMyPrint • • 21h ago

Fix My Print First Layer Infill not sticking to Walls

Post image
3 Upvotes

So today the first layer infill does not want to stick to the wall anymore.
Looks like on every turn from the wall, the filament gets pulled back a bit with the nozzle.
That is the first time, I see this phenomen after 670h printing with this printer.

Filament: Bambulab Matte
Printer Bambulab X2D with 0,2mm nozzle
First Layer speed: 30 for walls / 70 for infill

What I have tried so far:

  • Dried filament
  • Cleaned Printplate
  • Calibrated Filament and Printer
  • Played around with overlapping infill / wall setting