r/FixMyPrint • • 9m ago

Discussion Es compatible con bambulab?

Post image
0 Upvotes

r/FixMyPrint • • 31m ago

Helpful Advice Little debbies sprinkles

Post image
0 Upvotes

Hello!

I’m trying to print the little debbie christmas cake tree. The slicer seems to add supports to the sprinkles and some look like they aren’t touching the tree. I added supports manually but I’m still worried that the sprinkles aren’t going to print correctly. Does this look ok? I don’t have a warning for floating areas.


r/FixMyPrint • • 1h ago

Fix My Print Stringing to prime tower, color bleeding, surface quality & purge waste tips — Flashforge AD5X

Thumbnail
gallery
4 Upvotes

Hey everyone, I’m running into a few issues on my Flashforge AD5X (0.4mm nozzle, PLA) and attached 4 photos showing what’s happening across different prints:

Stringing: Lots of fine strings between the models and the prime tower, plus oozing blobs on the tower walls (seen on the bear and pink cat build plate photos).

Color bleeding/staining: Black/dark filament is bleeding into the white and pink sections (visible on the cats' faces and joints).

Surface/Overhang quality: Layer gap right above the threads on the orange cap, and rough top surfaces.

I’m currently using the default printer profile in the slicer (with flush into infill and filament-saving/retraction options enabled). Aside from fixing these quality issues, I’d love recommendations on how to tune flushing volumes to save filament during color swaps without getting color bleed, as I feel like it wastes way too much material right now.

For those running the AD5X, what should I tune first?


r/FixMyPrint • • 1h ago

Fix My Print How do i fix this issue?

Post image
1 Upvotes

r/FixMyPrint • • 1h ago

Fix My Print Is this just a bad roll of filament?

Thumbnail
gallery
3 Upvotes

It's Elegoo Rapid PETG on my centauri carbon. I've printed many things in black on this same filament with no issues. I noticed a similar issue using the gray roll last week so I put it through a turn in the filament dryer (in addition to cleaning the build plate and leveling etc.) so I don't think it's wet.

I used the default profile for this filament in Elegoo slicer and didn't do anything out of the ordinary. I am especially curious why the other object looks okay. I stopped this print on the fourth or fifth layer after the little blobs of filament started flying around.

Let me know if any more info is needed to diagnose, thanks in advance!


r/FixMyPrint • • 1h ago

Fix My Print X2D printing issue

Post image
1 Upvotes

Anyone even knows what causes this issue or what's it called?

This is printed with support underneath it, it's like the printer doesn't treat it as a face layer? Everything else is perfect just not this.

Printing with PETG, what do I change to test a solution?


r/FixMyPrint • • 2h ago

Fix My Print INDX 8T Terrible Torture Toaster

Thumbnail
gallery
2 Upvotes

I let my newly assembled INDX 8T print a torture toaster overnight and I'm disappointed with how it turned out. As you can see, there was a ton of stringing and blobbing, especially the "clockspring3d" logo on the back. There's so much blobbing that none of the tolerance sliders moved and the plunger broke before it could dislodge the pink toast. Since I printed it overnight, I couldn't watch it to try to diagnose the problem.

I'm not convinced yet that it's wet filament since I always thoroughly dry my filaments before storing them in sealed totes with 10-20% humidity, so I'm at least 80% confident that they're all dry.

That being said, it does look like the red is the cuprit, so my next step is to dry the red again and try another PLA.

That also being said, it's a nearly 12 hour print, and I am brand new to multi-extruder printing, so I know only a subset of my single-toolhead 3D printing knowledge applies. I figured I'd ask this sub if there's anything specific to the INDX that could fix this problem that I don't know yet before I wait another day to see another failed toaster.

Thanks for reading and thanks for any and all advice

Edit: I noticed blobs were sticking to the nozzle after wiping so I raised the wiper up a bit and that seems to have mostly solved that problem. We'll see after a test print. The nozzles still aren't getting as clean as I'd like, so I'd like to look into an improved wiper solution eventually.


r/FixMyPrint • • 2h ago

Fix My Print Why is my first layer so messy, the rest of the print turns out perfect.

Thumbnail
gallery
1 Upvotes

Elegoo CC2

Elegoo PLA

Elegoo Slicer 1.5.3.5

Nozzle 220c

Bed 55c

Cooling settings in screenshot 3rd pic

Like the title, very happy with the rest of the print, just the layer in contact with the bed seems to be a mess.

Thanks all


r/FixMyPrint • • 2h ago

Fix My Print Need help figuring out why this happens, please

Post image
1 Upvotes

r/FixMyPrint • • 2h ago

Fix My Print can't deal with settings

Thumbnail gallery
2 Upvotes

r/FixMyPrint • • 2h ago

FDM How do you work around the output of .gcode to .stl to get the same tolerances of the original model?

Thumbnail
reddit.com
1 Upvotes

r/FixMyPrint • • 2h ago

Troubleshooting Need help with overhangs

Thumbnail gallery
3 Upvotes

I tried different temperatures and speed, but there is no good result. What else i can do to make them better? Printed with Bambu Lab Pla Matte


r/FixMyPrint • • 3h ago

Fix My Print Everything prints fine until a certain point every time this happens, any reasons why and how I can fix it?

Thumbnail
gallery
1 Upvotes

The nozzle has scratched the big plates surface as u can see on the middle and right side of the plate. It’s done this before I went in and change the z-offset to make it a little farther away from the plate, but it doesn’t even scratch the plate it’s only when it gets higher than this starts happening.

On the big plate the left side you can see the roughness (idk what the right term is), and with the stands they’re supposed to be a press fit to create a larger stand, but you can see that for one everything is good besides insert end on it where the printer for some reason curved off it seems.

The other stand you can see that the filament actually got attached strung over it. I don’t even know how or why this happens especially when the others one surface came out pretty good.

I have a SOVOL SV06
And my slicer is Creality
Filament is SOVOL PLA
Nozzle temp is 200°, and bed temp is 60°
Print speed: Velocity: X: 500, Y: 500, Z: 10
Acceleration: 500, Retract acceleration: 1000, Travel acceleration: 500

I printed this slow as well, ~80% of the speed. I’m thinking it’s z offset, but this is only happening on one side of the parts, the really messed up stand and the rectangle plate messed up side were on the same side of the entire printing plate.

Any advice is really appreciated, it’s for a school project, and this is setting me back a decent amount until I can figure out the issue

Thank u in advance


r/FixMyPrint • • 3h ago

Fix My Print What could I learn from this?

Thumbnail gallery
1 Upvotes

Hey there, just finished printing this cutting board holder and as you can see, the quality is atrocious.

I’m trying to understand what the main cause of the issue is. Slicer settings are mostly unchanged, I moved seams to the back and I did shrink the model a bit but other than that, no major settings were changed.

Filament is addnorth PLA. Maybe I should download their filament profiles (that I just remembered they have).
But in general, I’m wondering if there’s something else I should keep an eye about or learn, for the future.


r/FixMyPrint • • 5h ago

Fix My Print What causes this

Post image
4 Upvotes

Hi, im using bambu x2d default profile of 0.2 quality, the material is pla .

Just wanted to know what causes this


r/FixMyPrint • • 5h ago

Troubleshooting Layer separation on overhangs with supports

Thumbnail
gallery
1 Upvotes

How do i fix this? i use bambu lab p1s and petg hf


r/FixMyPrint • • 11h ago

Fix My Print Pre-foamed LW-PLA Wing Hull Line

1 Upvotes

I have been printing airfoils and all is well, except for the hull lines where internal ribs are located. While I will be finishing this will putty primer, I just want to know its root cause and possible fixes

Right in the middle where internal ribs are
Same spot as the first photo
Wall Loops = 2, Top/Bottom solid infill/wall overlap = 15%
Infill/wall overlap = 10%

I use Ender 3 V2 Neo with dual drive extruder in bowden setup. Calibrated Settings with Polylite Prefoamed LW-PLA:

Nozzle Temp: 220C

Bed Temp: 60C First layer, 50C the rest

Flow Ratio: 1.03

Max Volumetric Flow Rate: 4.8

Min/Max Fan Speed: 30/40

Wall Generator: Classic

Wall Printing Order: Outer/Inner

Ensure Vertical Shell Thickness: Critical Only

Running on stock firmware, so no pressure advance. Extrusion Rate Smoothin = 10 and apply only on external features to compensate somehow for lack of PA.

Thank you in advance!


r/FixMyPrint • • 11h ago

Troubleshooting Z Offset issues (Anycubic Kobra S1)

Post image
2 Upvotes

r/FixMyPrint • • 12h ago

Troubleshooting Inconsistent first layer, done all the built in calibrations.

Thumbnail gallery
1 Upvotes

r/FixMyPrint • • 13h ago

Fix My Print Why did my model get this artifacts?

Post image
0 Upvotes

r/FixMyPrint • • 14h ago

Troubleshooting Small holes on the edges

Post image
3 Upvotes

How do i remove these small holes on my prints? I have already did Pass 1 flow rate calibration and temp calibration. but these holes are very annoying. When i changed flow rate from 0.9975 to 1.00 it removed it but had some minor overextrusion

Printer: Sparkx i7

Filament: Polymaker Panchroma Matte Forest Green, dried 50C at 8H


r/FixMyPrint • • 14h ago

Fix My Print Need help with correcting my print.

Thumbnail
gallery
3 Upvotes

I am a newbie to using a 3D printer. I have an Bambu lab A1 mini. I have tried a few prints but they all have had issues. I am hoping someone can offer some advice on how to correct my issue. I am submitting two images of m issue. I’m hoping someone can help me with this matter.

Thank you


r/FixMyPrint • • 14h ago

Discussion Cloned objects have different top layer... why?

Post image
4 Upvotes

This doesn't need a fix, but I am super curious. One object was cloned six times. When I went to slice it, the final layer does not cover the full surface for four of the seven objects. I noticed the coverage ending lines up with the seam, but why is it doing that on only some of the objects when they are all identical clones?

If it matters, I'm using OrcaSlicer with my Flashforge AD5M. Thank you.