r/FixMyPrint • • Mar 29 '20

Asking for help... and how to actually get it

Post image
774 Upvotes

r/FixMyPrint • • Nov 05 '24

Helpful Advice Here’s your daily reminder to dry your filament

Post image
293 Upvotes

Thought it was stored dry so I’d try printing without drying first as it wasn’t going to use much filament anyway, didn’t get away with it this time but after 6 hours of drying it printed perfectly 👌 Sunlu dryer at temp setting 2 for Matte PLA with a load of colour changing silica gel in the middle of the role rather than in the compartment at the back of the dryer


r/FixMyPrint • • 1h ago

Fix My Print Stringing to prime tower, color bleeding, surface quality & purge waste tips — Flashforge AD5X

Thumbnail
gallery
4 Upvotes

Hey everyone, I’m running into a few issues on my Flashforge AD5X (0.4mm nozzle, PLA) and attached 4 photos showing what’s happening across different prints:

Stringing: Lots of fine strings between the models and the prime tower, plus oozing blobs on the tower walls (seen on the bear and pink cat build plate photos).

Color bleeding/staining: Black/dark filament is bleeding into the white and pink sections (visible on the cats' faces and joints).

Surface/Overhang quality: Layer gap right above the threads on the orange cap, and rough top surfaces.

I’m currently using the default printer profile in the slicer (with flush into infill and filament-saving/retraction options enabled). Aside from fixing these quality issues, I’d love recommendations on how to tune flushing volumes to save filament during color swaps without getting color bleed, as I feel like it wastes way too much material right now.

For those running the AD5X, what should I tune first?


r/FixMyPrint • • 1h ago

Fix My Print Is this just a bad roll of filament?

Thumbnail
gallery
3 Upvotes

It's Elegoo Rapid PETG on my centauri carbon. I've printed many things in black on this same filament with no issues. I noticed a similar issue using the gray roll last week so I put it through a turn in the filament dryer (in addition to cleaning the build plate and leveling etc.) so I don't think it's wet.

I used the default profile for this filament in Elegoo slicer and didn't do anything out of the ordinary. I am especially curious why the other object looks okay. I stopped this print on the fourth or fifth layer after the little blobs of filament started flying around.

Let me know if any more info is needed to diagnose, thanks in advance!


r/FixMyPrint • • 5h ago

Fix My Print What causes this

Post image
5 Upvotes

Hi, im using bambu x2d default profile of 0.2 quality, the material is pla .

Just wanted to know what causes this


r/FixMyPrint • • 3h ago

Troubleshooting Need help with overhangs

Thumbnail gallery
3 Upvotes

I tried different temperatures and speed, but there is no good result. What else i can do to make them better? Printed with Bambu Lab Pla Matte


r/FixMyPrint • • 2h ago

Fix My Print INDX 8T Terrible Torture Toaster

Thumbnail
gallery
2 Upvotes

I let my newly assembled INDX 8T print a torture toaster overnight and I'm disappointed with how it turned out. As you can see, there was a ton of stringing and blobbing, especially the "clockspring3d" logo on the back. There's so much blobbing that none of the tolerance sliders moved and the plunger broke before it could dislodge the pink toast. Since I printed it overnight, I couldn't watch it to try to diagnose the problem.

I'm not convinced yet that it's wet filament since I always thoroughly dry my filaments before storing them in sealed totes with 10-20% humidity, so I'm at least 80% confident that they're all dry.

That being said, it does look like the red is the cuprit, so my next step is to dry the red again and try another PLA.

That also being said, it's a nearly 12 hour print, and I am brand new to multi-extruder printing, so I know only a subset of my single-toolhead 3D printing knowledge applies. I figured I'd ask this sub if there's anything specific to the INDX that could fix this problem that I don't know yet before I wait another day to see another failed toaster.

Thanks for reading and thanks for any and all advice

Edit: I noticed blobs were sticking to the nozzle after wiping so I raised the wiper up a bit and that seems to have mostly solved that problem. We'll see after a test print. The nozzles still aren't getting as clean as I'd like, so I'd like to look into an improved wiper solution eventually.


r/FixMyPrint • • 2h ago

Fix My Print can't deal with settings

Thumbnail gallery
2 Upvotes

r/FixMyPrint • • 12m ago

Troubleshooting Centauri Carbon 2 Combo won’t print reliably

1 Upvotes

Hello all,
I have had my CC2 combo since June, and have logged 273 hrs of print time since then, my hotend snapped and I got a new one and replaced it myself, but since I replaced it my prints either don’t adhere to the print bed whatsoever and when it’s extruding, it extrudes and curls onto the nozzle itself. Or, I get a few layers into a print and it then clogs its nozzle. However, I have managed to get 2 small prints to work, each being little test cubes I found online, these prints have very wrinkly edges, and the top face is very deformed and looks like it’s been rammed into by the nozzle

I’ve been printing with JAYO PLA, with files I found from Elegoo slicers online models, and I have been using Elegoo slicer. Nozzle temp is 210 degrees C and my bed temp is 60 degrees C

Speeds (mm/s) :
First layer - 50
First layer infill - 105
Outer wall - 160
Inner wall - 200
Sparse infill - 200
Internal solid infill - 250
Top surface - 200
Gap infill - 250
Support - 150
Support interface - 80

I do not have reduced infill retraction enabled, and I don’t know of any other settings under “retraction settings”

For context, I have played around with my z-offset, the tension of my extrusion spring and cleaning my bed repeatedly. I have also replaced my hotend before and had no issues once it was done, so I believe I have carried out the replacement correctly, but I have been trying to fix this for 4 days now and cannot find anything on the internet that co-insides with what I’m going through. I have also printed using JAYO PLA for almost all of the time I have had the printer, so I do not believe that is the issue

Any help would be appreciated!


r/FixMyPrint • • 22m ago

Fix My Print Failed print.

Thumbnail
gallery
1 Upvotes

Printer: bambu labs A1

Nozzle: 0.4mm

Filament Type : PLA

This print was covering almost the width of the plate and it took off from one edge


r/FixMyPrint • • 22m ago

Troubleshooting Transparent PLA filament just doesn't want to stick to the printing surface.

Thumbnail
gallery
1 Upvotes

I'm using an Artielly Hornet printer with transparent filament, on 207C° nozzle and a 60C° bed with 214C° starting heat, and got2b extra strong hairspray as a fixing agent for the layers. Previously I used paper glue tube as some recommended. I use isopropyl alcohol to clean the printing between usages.

Some warping also occurred during the print, and I just simply can't fine-tune the thing...

Already started this print 4 (or more) times, but it always fails around the 1 hour mark.

What frustrates me, that a few days ago I did a 7 hour print without an issue using dark-grey PLA from the same brand.

Is there some adjustment necessary for clear filament printing?


r/FixMyPrint • • 31m ago

Fix My Print Overhang/wall issues

Thumbnail
gallery
1 Upvotes

What am I missing? I feel like I’ve tried every setting involving walls. Because these sections are slanted the slicer sees it as walls not top surfaces. I got a new extruder and am trying to print a part cooling duct. I’ve tried to find the most simple part in regards to geometry as I don’t have any part cooling possible. lol. I’m using Orca slicer but for the life of ,e I can’t figure out what I’m doing wrong. Hopefully someone here can help.


r/FixMyPrint • • 41m ago

Discussion Es compatible con bambulab?

Post image
0 Upvotes

r/FixMyPrint • • 1h ago

Helpful Advice Little debbies sprinkles

Post image
0 Upvotes

Hello!

I’m trying to print the little debbie christmas cake tree. The slicer seems to add supports to the sprinkles and some look like they aren’t touching the tree. I added supports manually but I’m still worried that the sprinkles aren’t going to print correctly. Does this look ok? I don’t have a warning for floating areas.


r/FixMyPrint • • 1h ago

Fix My Print How do i fix this issue?

Post image
1 Upvotes

r/FixMyPrint • • 19h ago

Troubleshooting WHY is this edge curling at the same spot every time?

Thumbnail
gallery
26 Upvotes

Hello everyone. Im a bit desperate at this point I have to admit. I want to print this specific poop bin but it failed spectaculary the first time, as you can see in the second picture. Since then I calibrated my filament and tweaked some settings that might be the reason. The second print started curling again. And I dont know why. Its always also this one edge on the exact same height of the print.

Stats:

PLA

Nozzle 210

Bed 50 (BIQU Glacier)

Part Fan 100%

Auxiliary Fans 70-80% (with printed diffusors)

So yeah. I dont know what to do. Never had this happen before. Can anyone help?


r/FixMyPrint • • 2h ago

Fix My Print X2D printing issue

Post image
1 Upvotes

Anyone even knows what causes this issue or what's it called?

This is printed with support underneath it, it's like the printer doesn't treat it as a face layer? Everything else is perfect just not this.

Printing with PETG, what do I change to test a solution?


r/FixMyPrint • • 2h ago

Fix My Print Why is my first layer so messy, the rest of the print turns out perfect.

Thumbnail
gallery
1 Upvotes

Elegoo CC2

Elegoo PLA

Elegoo Slicer 1.5.3.5

Nozzle 220c

Bed 55c

Cooling settings in screenshot 3rd pic

Like the title, very happy with the rest of the print, just the layer in contact with the bed seems to be a mess.

Thanks all


r/FixMyPrint • • 2h ago

Fix My Print Need help figuring out why this happens, please

Post image
1 Upvotes

r/FixMyPrint • • 2h ago

FDM How do you work around the output of .gcode to .stl to get the same tolerances of the original model?

Thumbnail
reddit.com
1 Upvotes

r/FixMyPrint • • 3h ago

Fix My Print Everything prints fine until a certain point every time this happens, any reasons why and how I can fix it?

Thumbnail
gallery
1 Upvotes

The nozzle has scratched the big plates surface as u can see on the middle and right side of the plate. It’s done this before I went in and change the z-offset to make it a little farther away from the plate, but it doesn’t even scratch the plate it’s only when it gets higher than this starts happening.

On the big plate the left side you can see the roughness (idk what the right term is), and with the stands they’re supposed to be a press fit to create a larger stand, but you can see that for one everything is good besides insert end on it where the printer for some reason curved off it seems.

The other stand you can see that the filament actually got attached strung over it. I don’t even know how or why this happens especially when the others one surface came out pretty good.

I have a SOVOL SV06
And my slicer is Creality
Filament is SOVOL PLA
Nozzle temp is 200°, and bed temp is 60°
Print speed: Velocity: X: 500, Y: 500, Z: 10
Acceleration: 500, Retract acceleration: 1000, Travel acceleration: 500

I printed this slow as well, ~80% of the speed. I’m thinking it’s z offset, but this is only happening on one side of the parts, the really messed up stand and the rectangle plate messed up side were on the same side of the entire printing plate.

Any advice is really appreciated, it’s for a school project, and this is setting me back a decent amount until I can figure out the issue

Thank u in advance


r/FixMyPrint • • 4h ago

Fix My Print What could I learn from this?

Thumbnail gallery
1 Upvotes

Hey there, just finished printing this cutting board holder and as you can see, the quality is atrocious.

I’m trying to understand what the main cause of the issue is. Slicer settings are mostly unchanged, I moved seams to the back and I did shrink the model a bit but other than that, no major settings were changed.

Filament is addnorth PLA. Maybe I should download their filament profiles (that I just remembered they have).
But in general, I’m wondering if there’s something else I should keep an eye about or learn, for the future.


r/FixMyPrint • • 6h ago

Troubleshooting Layer separation on overhangs with supports

Thumbnail
gallery
1 Upvotes

How do i fix this? i use bambu lab p1s and petg hf


r/FixMyPrint • • 15h ago

Discussion Cloned objects have different top layer... why?

Post image
4 Upvotes

This doesn't need a fix, but I am super curious. One object was cloned six times. When I went to slice it, the final layer does not cover the full surface for four of the seven objects. I noticed the coverage ending lines up with the seam, but why is it doing that on only some of the objects when they are all identical clones?

If it matters, I'm using OrcaSlicer with my Flashforge AD5M. Thank you.