r/Locksmith • • 21h ago

I am a locksmith What expensive solutions have you installed lately?

Thumbnail
gallery
27 Upvotes

Recently installed this solution on 6 doors. More doors in the next weeks.

Double motorized mortises, panic pushbar. These 6 are in an external nook without a roof, so is gonna be interesting to see how well they fare in the elements.

But this got me curious to see what others expensive installs have been lately, share below :)


r/Locksmith • • 21h ago

I am NOT a locksmith. What does this bolt need to operate?

Thumbnail
gallery
7 Upvotes

This surface mount bolt had a cone spring inside, but it had snapped in half. When I went to get a replacement spring the hardware store was surprised that the lock would have that inside. Can anyone tell me what sort of spring the lock needs and where it should go?


r/Locksmith • • 10h ago

I am NOT a locksmith. Replacing a Schlage Door Handle

Thumbnail
gallery
6 Upvotes

I have a door handle that's ~20 years old and the lock button popped off. I have another door handle of the same type where the handle is is out of alignment with the other handle. I picked up a couple of Schlage door handles to replace both of the door handles thinking it would be a 20-30 minute job.

I've spent more time than I care to admit fiddling around with this. If you have ideas on how to get this handle removed, I would be eternally grateful.

I've watched every YouTube video I can find on how to remove these things and I'm not able to do it.


r/Locksmith • • 6h ago

I am NOT a locksmith. Cylinder cap

Post image
3 Upvotes

So, I'm just tinkering and I took this little brass sheet out of an old schlage cylinder. Now it won't go back.

Do I need to bend the little tabs out, place the cover, then re-bend the tabs in?

Or is this a lost cause?


r/Locksmith • • 6h ago

I am NOT a locksmith. What are my options for this lock?

Thumbnail
gallery
3 Upvotes

So I’m a first time homeowner and I’ve run into my first annoying issue. We want to change out this deadbolt for an electronic Schlage BE365 lock so we don’t have to give people a key or hide a key or anything like that. When I went to put the lock on the casing, overlaps the bottom knob and so will never be flat (face palm). In general, it seems like the deadbolt and knob are really close together.

What are my ways out of this? Replacing the door is silly. I don’t see any other good locks that would work with this spacing. Is it possible to move the hole up and like patch it?


r/Locksmith • • 14h ago

I am NOT a locksmith. Purchased 3 Baldwin locks and the lock spins but won’t lock.

3 Upvotes

I just had 3 new doors with Baldwin Contemporary Single Cylinder Keyed Entry Door Knob with Square Rose installed. The installer said they have never seen the lock not able to be used. The lock and key turn as one piece. The key turns the device but it won’t lock. I am unable to move the lock on the back. Any trouble shooting tips before he leaves? He is stumped. I am stumped.


r/Locksmith • • 19h ago

I am NOT a locksmith. Extend tailpiece for Yale Lever Lock

3 Upvotes

I bought a Yale Lever lock for an exterior patio door and the door with is slightly too wide. I was able to switch from 22 mm screws to 30 mm screws to get both sides of the lockset attached, but the tailpiece is barely short. Are there any options that don’t require soldering or something that could be a simpler adjustment? Yale of course told me to return it as they are not made for that size of door so they were not helpful. Only reason I’m trying to stick with Yale is because I have 3 other doors that already have them stalled.


r/Locksmith • • 9h ago

I am NOT a locksmith. are the 2 compatible?

2 Upvotes

hi im new to this, i am planning to get EAZEA S-80 Magnet-Proof Digital Letterbox Lock and fit it to Yale YKB/200/BB2 key box. do let me know if the fit works or if theres a product that already has digital lock for small keyboxes thanksss