r/PCB • • 13h ago

HIGH power nice esc

Thumbnail
gallery
49 Upvotes

Hello everyone!

Just wanted to share my latest design: a high-power 16S 200A ESC, intended for automotive applications such as lightweight electric vehicles.Originaly did it for my internship that's why i documented things, get to create a public github of it because it is intended for a bench too not a big confidential desing for the company originaly it wasn't asked to me at all, i proposed to do that on bonus, i will use it on my small ebike i think we can push this design over 300A or more need to test the cooling but thanks to TOLT mosfet a great cooling is easily achievable.

It features:

  • Infineon OptiMOS 5/6 MOSFETs in TOLT packages (top-side cooling)
  • Proper bulk capacitors and MLCC decoupling
  • INA241 inline shunt current sensing
  • STM32G4 MCU
  • Two separate PCBs: one for power and one for control

I've tested it using DPT to check Vds voltage overshoot and switching transients. I couldn't accurately measure Eon and Eoff due to my inline shunt resistors, but the results look great so far.20V overshoot too 50 percent overshoot at 200A on phase same result at 328A (due to slower turn on and off time too di/dt similar)

I'll also upload my FOC code to the same repository later on.

PS: on bottom view the small 1mohm sensing resistor are not final one and i didn't do the DPT with thos final one are 2 9W 0.2 milliohm resistors

If you're interested, feel free to check out the project, and maybe leave a star if you like it!

GitHub: https://github.com/mathieupommery/NICE_ESC

Any feedback or suggestions are welcome!


r/PCB • • 6h ago

First ever PCB (feedback?)

Thumbnail
gallery
16 Upvotes

Zero use of AI. One night class per week and a lot of reading!

RPi 4b hat, 4 layers.
1/red: signal traces and power/ground zones;
2/green: ground plane;
3/orange: power zones, including 12v (batt/acc), 5v and 3v3;
4/blue: audio in and ESP related stuff.

12v to 5v 3A buck converter, ESP32-C3 to communicate between the RPi and headunit. What could I have done differently?

Thanks!


r/PCB • • 14h ago

[Review Request] 4 layer RP2040 + USB-C board, 50 x 49 mm, KiCad 10

Thumbnail
gallery
6 Upvotes

Hi r/PCB, I would like a review before I order this. It is a small RP2040 board with USB-C, 7 LEDs, BOOT and RESET buttons and a push switch.

Gallery order: 1 top composite, 2 to 4 3D views, 5 to 8 copper layers L1 to L4, 9 full schematic, 10 to 14 schematic zoomed in sections, 15 stackup and impedance table.

Board

  • 4 layers, FR4 Isola 370HR, about 62 mil, 1 oz copper on all layers
  • L1 parts and USB pairs, L2 solid GND, L3 3.3 V plane, L4 other signals
  • 50 x 49 mm L outline, four M4 plated holes tied to GND, all parts on the top side
  • USB pairs: 5.0 mil trace, 4.0 mil gap, 90 ohm differential, on L1 over L2
  • 6 mil min track and space elsewhere, 8 mil min drill, 8 mil drill to copper, 12 mil tented through vias, IPC Class 2, 1 A max
  • KiCad DRC and ERC are clean
  • Layout was scripted and most non critical nets were autorouted, so it is not hand tidied

Questions

  1. USB pairs at 5/4 mil on L1. The fab table says 89.7 ohm, my field solver says about 94.5 ohm. Is that a yield risk?
  2. The stackup table shows 0.5 oz inner copper, but I am using 1 oz inner. Does that change the impedance enough to worry about?
  3. Five tented 12 mil ground vias in the RP2040 centre pad. OK, or should I move or fill them?
  4. The USB-C footprint is custom from the datasheet (0.40 mm holes, 5.5 mil annular ring, 0.60 mm shell slots). Anything wrong?
  5. 8 mil power neck downs at the RP2040 pads (16 mil elsewhere) with a 1 A max. Fine?
  6. L4 routing: return paths, anything crossing plane gaps, anything a fab would flag.
  7. One sided assembly with a through hole push switch and USB-C. Any assembly problems?

KiCad 10.0.8. I can share Gerbers or the project if that helps. Thanks!


r/PCB • • 7h ago

PCB isolation slots smaller than JLCPCB's 1 mm minimum?

4 Upvotes

I'm designing a 60 W AC/DC flyback charger based on Power Integrations' RDR-838 reference design.

The reference PCB appears to use non-plated isolation slots narrower than 1 mm. However, JLCPCB specifies a 1 mm minimum for non-plated slots.

I understand the reference board wasn't necessarily manufactured by JLCPCB, but how are manufacturers achieving narrower isolation slots? Is this a fabrication capability limitation, or am I misunderstanding the specification?


r/PCB • • 8h ago

About to produce my first proper PCB. How badly wrong can it go?

4 Upvotes

I have been working on my first proper PCB for about six months and I'm very close to the point where I'm going to have some engineering samples manufactured and assembled.

Background: there is none. This is a hobby project which I sort of span off something I did for work a while ago and it snowballed into consuming a significant amount of time, with immense scope creep and it's gone from something that was just going to be for learning/development and a couple of boards which would be mainly for personal use, to something that I am seriously considering turning into a commercial product, or at least it'll be the backbone of a potential commercial service.

The board is an asset tracker. I know these are widely available already but none meet the specific requirements I had in mind originally...and mine is extremely flexible now.

Four layers, 96x48mm, and has RF (LTE/LoRa and GNSS). Power is via battery, USB, external DC input (all can be connected simultaneously, with DC prioritised over USB; it will charge the battery too). The brains is an RP2350A.

Disclaimer: I am not an electronics expert and I have used AI to help with the schematics and part selection. I did a rough layout myself, and I am paying JLC to do the routing. There has been a bit of back and forth as me (and AI) have spotted small issues which the JLC engineer has happily rectified. I have tried my best to meticulously follow the hardware design guide for every chip on the board, some of which are very stringent (anyone who has put an RP2350A on a board will know about that inductor). I'm obviously not an expert but it looks to me like JLC has done a pretty good job with the first pass of the routing, and the impedance control seems to follow best practice. The PCB does not have antennas; there are U.FL connectors for both modules and they are on opposite edges of the long sides of the board and the areas around the RF traces are densely stitched with vias.

I've done some PCBA quotes with JLC and it looks like I can get the first 6 boards manufactured for just under US$100 each all in, which is great because it's below my target price. There are three hardware versions of the board which are virtually identical other than using different modems (two LTE and one LoRaWAN) and I'm going to panelize all three and then get two panels assembled as the engineering samples as this seems the most economical way to do it. I obviously really want the first versions to just work, although I am anticipating there will be at least one issue. I've become so obsessed with trying to ensure perfection with the v1 samples that I keep going through the schematics triple-checking them, re-reading all of the datasheets to make sure I've done everything right, and I'm sometimes even having nightmares about it. Each time there's something minor I find that I want to change although most of these would probably not cause the boards to be a complete failure.

So after all that my question really is: what else is there that can go wrong, even if I get everything right? Can JLC mess up the assembly and send me dead boards? Can parts be oriented wrong because datasheets have got incorrect diagrams?

Really appreciate any input, and as I said I'll post up some schematics and the layout for review once I get the latest version from JLC.


r/PCB • • 8h ago

Is soldering a shared ground line on the underside of a perfboard good practice?​

Thumbnail
gallery
2 Upvotes

​Hi everyone,

​I'm new to soldering on perfboards/protoboards (until now, I've only used Arduino breadboards). I'm currently wiring up a small circuit with tactile pushbuttons and LEDs.

​To keep the top side looking clean and reduce wire clutter, I decided to create a common ground rail on the underside of the board by bridging/soldering the ground connections together, and I plan to route the remaining signal/power wires normally.

​Is this a valid and reliable technique on perfboards, or are there downsides I should watch out for (like short circuits or cold joints)? I've attached photos showing the top side with wires, the board without wires, and the underside soldering.

​(P.S. Apologies for the messy solder joints—this is my very first time soldering!)


r/PCB • • 1h ago

Is it safe not to isolate the MCU ground?

Post image
1 Upvotes

Can anyone experienced with this help me?


r/PCB • • 5h ago

Looking for a solid toolset (or workflow) for designing proper FPGA-level PCBs — what are people actually using successfully today?

1 Upvotes

Hey everyone,
I’m looking for recommendations on a complete or near-complete toolset that can handle proper PCB design for FPGA boards (not just simple breakout boards). Think multi-layer boards with high-speed interfaces, careful power integrity, decent length matching, proper decoupling, etc.
Has anyone here put together a reliable combination of tools that actually works well for this level of design as an individual?
I’m especially interested in:
• What schematic + layout tools people are using successfully for FPGA boards
• Any supporting tools for SI/PI, length matching, constraint management, etc.
• Whether you’ve managed to build a workable end-to-end workflow without needing the full enterprise packages
• What’s currently considered the strongest option available to individuals in 2026
If you’ve gone through this process yourself and settled on something that actually works, I’d really appreciate hearing what you ended up with and why.
Thanks in advance.


r/PCB • • 9h ago

Designed a PCB in under 3 minutes with TurboPCB, then milled, solder-masked and drilled it on my desktop CNC

Thumbnail
reddit.com
1 Upvotes

r/PCB • • 23h ago

Using Nexar while waiting for Altium MCP access

Thumbnail
reddit.com
0 Upvotes

r/PCB • • 20h ago

Thread SED Weather Sensor - PCB Design

Post image
0 Upvotes

r/PCB • • 20h ago

[Review Request] 4-layer AIO drone board: ESP32-S3 FC + 4-in-1 AM32 ESC + ELRS RX, 2S, 55×115 mm

Thumbnail gallery
0 Upvotes