r/RetroAR • u/nojo422 • 14h ago
I call it the ACE Omega Holosight Gangster Laser Blaster
r/RetroAR • u/nojo422 • 14h ago
r/RetroAR • u/curbsmile • 8h ago
BKF A2 upper
BA Mid length gas government 16" barrel
Unrivaled A2 siege brake
Midwest Industries 2 piece free float 9" handguard
BKF carry handle rail, waiting on Aimpoint PRO
GRIFFIN mk1 blem lower
Troy ambi mag release
CMMG Zeroed bolt catch
BCM MK2 buffer system
Law Tactical Gen S folder.
Geissele SSA Trigger
GG&G Shorty foregrip
I didn't really clone anything, but I'm happy with the results.
r/RetroAR • u/CyberPolack • 10h ago
Don’t have access to a drill press but it came out pretty decent considering all I used was a cordless power drill with a 5/16” bit and two C clamps. Drilled a little too far to the left and into the ridge of the receiver extension but was able to drill a small pilot hole on the right of the hole to get it more centered on my second attempt. The stock pin sits in the hole surprisingly well and has the same amount of wobble as the factory holes. Gave the stock a couple of good smacks too and it’s nice and secure.
If anyone wants to attempt this without a drill press it’s actually pretty easy granted you have a vise or some C clamps. I measured the exact distance from the front face of the stock (see red line in 4th pic) back to the center of the locking pin inside the stock body. It came out to 2 3/8” for me. I then slid the stock onto the tube, shouldered the rifle in my chest rig to find the sweet spot, and marked the buffer tube right where the front edge of the stock sits with a pencil. After that, I removed the stock and measured backwards (toward the rear of the tube) 2 3/8” from the pencil mark. I then marked the spot for the new hole with a pencil and drilled it out.
r/RetroAR • u/SLN583 • 21h ago
On the night of 21 November, 1970, 56 years ago, OPERATION IVORY COAST, the raid on the Son Tay prisoner of war camp in North Vietnam was successfully executed. I took these pics a few years ago at the JFK Special Warfare Museum on Fort Bragg. This is the actual sand table used to plan the mission, as well as some other items from the raid. That is not a real XM177e2 Carbine, but the single point optic and mount look authentic and were probably used on the raid.
r/RetroAR • u/TheRoach42o • 1d ago
Just picked this up. Slapped og furniture on it. Can't decide if I'm happy with the grey anodizing job on it or not. Wouldn't mind it a shade tad lighter.
r/RetroAR • u/fatdolsk • 6m ago
I have this lower, what should I do with it? Would rather sell
BKings 11.5” 733 style Upper
OCM6
OCL “Midway” mount
RRA Entry Stock
Temp Colt 4x until AGW M5000 can be acquired
CMC 2 stage “Combat Curve” trigger, but will probably replace with FRT w/ normal AR trigger blade
Chrome sand cut KAK down-vent/dual ejector bolt carrier
Had to grind off Bayo lug for clearance, but I like how it came out.
r/RetroAR • u/Reaper01Actual1970 • 1d ago
r/RetroAR • u/Jristrong • 22h ago
OCM6
DD Omega 7
H&R C7 upper with smith enterprises pic rail
PSA Squirrel-15 lower
Also I have an arcfire v1 with the mill spec trigger (I’ll upgrade the trigger later)
r/RetroAR • u/ComprehensiveSuit497 • 1d ago
20 dolla makes em holla
r/RetroAR • u/Neo13715 • 23h ago
Hi everyone, I just picked up this nice classic looking M4 AR-15. I got a scout mount (IWC TMC Scout Mount-N-Slot) and went to the local gun store to get it installed because I have pretty weak hands and couldn't push the delta ring down to remove the handguard. They managed to remove it but said the gas tube was interfering with the mount.
I don't want to use another kind of mount, I see that another user made a post of a similar comment regarding the gas tube and installation but his account is since then deleted so I can't ask how or what he did to "bend" the heat shield/guard to make it work. How would I go about doing this? Also, a picture of the AR because I'm just proud of how it looks :)

r/RetroAR • u/PsychologyHopeful706 • 1d ago
Is this the right cap for adding a tape switch to a surefire 6p?
r/RetroAR • u/Flat_chested_male • 2d ago
Left rifle - Colt 14.5” socom barrel, microbest bcg, Aimpoint comp2, bad attitude lower, H&R c7 gray upper, Colton armory car stock, model1 buttpad
Right rifle - centurion 14.5” midlength, OCM5, palmetto m16a2 lower, h&R black A2 upper, microbest chrome and phosphate small bits bcg, b5 car stock and model 1 buttpad.
Polished GI triggers, both have EZ tube gas tubes.
r/RetroAR • u/deviantdeaf • 2d ago
Shown with my 12" 6.5 Grendel retromod C7 carbine that now sports clamshells, CAR stock, CQB handguard rail with Bauer light and P&S grip.
Build data;
14.5 Dirty Bird chrome lined phosphate M4 barrel with pinned F FSB
Brownell carbine gas tube and KAK A2 flash hider with lock nut (I'm lazy lol)
KAC M4 quad rail
Late model black anodized Colt 6520 A2 upper with M4 ramps
Registered SBR Anderson lower (again, dumb state requires Fed paperwork to be lawful 🙄)
Schmidt tool trigger group
CMMG springs and pins
Random A2 grip
Not sure who made this 6 position mil spec sized carbine stock, has same two positions as military 2 position stock plus 4 in between
H2 buffer and spring
Brownell M4 stock with 8FW25 CAGE code
I just need to get it out and do a few mags breaking in and sighting in.
r/RetroAR • u/CeramicCoatingsChef • 3d ago
Receivers cerakoted a retro grey and purple anodizing match. The A2 lower started as a 601 profile 80% that I lasered to look like an overstamp rearsenal lower
r/RetroAR • u/pewsnpizza • 2d ago
M4 / Gordy Clone
Then retro-mod Gordy
Can’t decide how I want it lol
r/RetroAR • u/kill_all_pedophiles_ • 2d ago
Anyone make clamshell handguards for the kitty kat?
r/RetroAR • u/PakRatJR • 2d ago
I'm wanting to recoat a couple of my charging handles using Norrells moly coat.
It needs 300 degrees for a hour or so to cure.
I tried taking one apart years ago and gave up trying to get it back together after struggling with that damn small roll pin and kinda don't want to have to try it again if I don't need to.
r/RetroAR • u/-VictorusAutMortis- • 3d ago
r/RetroAR • u/Signal-Ship • 3d ago
Not sure what you would call it but here we are finally complete
r/RetroAR • u/CrabMan_99 • 4d ago
r/RetroAR • u/WaltzRPK • 3d ago
My RRA midlength HBAR and my ALICE kit. Nothing you haven't seen before, but I'm pretty happy with how they turned out.
The question of what the best tool is for removing and installing the old style spanner nuts has come up at least twice in the last several weeks. Not cheap, but definitely the best.