r/drywall • • 22h ago

How many bags?

Post image
4 Upvotes

Say I forgot track of my ready mix bags, (I did) and every time I run to the small hardware store for more easy sand, the guy always busts my balls. This is approx 2/3 of my 1500sq ft basement. How many easy sand bags would a contractor estimate? Approx 7' walls, 13-14' ceiling width.


r/drywall • • 4h ago

Hand sanding vs palm sander

0 Upvotes

Working on a large ceiling patch (4x4) and would like to know about the tradeoff between hand sanding and using a palm sander. Do you loose any precision with a palm sander?


r/drywall • • 22h ago

Fixing drywall backside before mounting?

Thumbnail gallery
1 Upvotes

First time drywaller here.

12ft drywall delivered with a slight crack. Got a bit worse after hauling it downstairs, but didn’t crack all the way through the front…also took a little brown paper off when cutting it down.

What should I do before I hang it? Shellac it? Nothing? I haven’t gotten to mudding yet so I don’t have anything mixed up yet.


r/drywall • • 23h ago

What to do about these paper wrinkles?

Thumbnail gallery
2 Upvotes

New homeowners here, looking for advice on our walls. The previous owners painted over old wallpaper, and was peeling off at the corners.

Brave us, decided to remove the wallpaper using steam and wet towel. while removing, we accidentally took off some of the drywall’s outer paper layer. We sealed the exposed areas with two coats of Zinsser GARDZ and are now skim-coating with general-purpose joint compound.

I was hoping the sealant would prevent exactly this. But now the paper wrinkles are showing from the first skim coat.

Any suggestions?


r/drywall • • 14h ago

How would I fix this crack?

Post image
2 Upvotes

Over the years our place has settled and formed a crack. Is this something I could just stick some spackle in the crack and sand and paint? Since there’s texture on the wall, I figured it would be best to just fill the crack rather than cut out the drywall and watch. Is that correct?


r/drywall • • 21h ago

Ceiling Gap…

Thumbnail gallery
4 Upvotes

First time drywalling…

When cutting out existing ceiling drywall to expose a beam, the cut got away from me.

One side is nice and tight, the other tapers from .75-1.75.

How should I got about filing the larger gap on the inside angle? Directly above is duct work if it makes a difference.


r/drywall • • 3h ago

What could I use to scrape this glue off it’s a block wall that got skimmed with compound and glued a backsplash later on… or should I just try and knock the high spots down and skim out the entire wall relatively thick

Post image
13 Upvotes

r/drywall • • 30m ago

First time doing drywall, how did I do?

Post image
3 Upvotes

r/drywall • • 3h ago

Old wall Opening in Ceiling. What to do.

Thumbnail gallery
2 Upvotes

I have taken out a non load bearing wall and need to seal the ceiling. The height does not match each other on either side.

Thinking about cutting it back to the ceiling joists and place some nailer on each side but don’t want to make it worse.

Any thoughts would be greatly appreciated.


r/drywall • • 1h ago

First time drywalling. How did I do?

Thumbnail gallery
44 Upvotes

This was my first time drywalling. I had to rip out a half wall railing at the bottom of my stair landing in order to replace the sagging osb landing. I then used AI to help design a taller wall that would function well to keep the cat from jumping over, and incorporate a pet gate, which I had to modify.

should I cut the bottom of the drywall so it’s not touching the floor, in case it absorbs a water spill or something? The flooring is being replaced as well, and I didn’t know that drywall shouldn’t touch the floor for moisture reasons.

I ended up having major paint bubbling in an area that I had to skim coat the wall with mud, and had to rework the wall and repaint. Not sure why I had such bad bubbling of what seemed to be the primer right after painting. What causes this?