r/electrical • • 20h ago

Well it happened (wago fail)

Thumbnail
gallery
417 Upvotes

Week old setup. Yea I made sure it's tight and inserted completely. No I don't know why. It's genuine as far as it looks. Yea I will continue using them.


r/electrical • • 3h ago

What Gauge wire is coming from 30Amp Breakers

Post image
34 Upvotes

Long story short my water heater should have 3 40 amp breakers but someone put 3 30s. Tried to follow the sheathing to see what gauge but no luck. If it’s 8 I can swap without having to run new wires which would be nice. Thanks m.


r/electrical • • 23h ago

0-140v transformer?

Post image
18 Upvotes

Found while cleaning out my late grandpa's garage. Just trying to figure out what this is used for


r/electrical • • 4h ago

How to extract sheared off screw in outside electrical box that is encased in limestone/mortar

Post image
15 Upvotes

I have tried making a pilot hole and then using the ryobi extractor but it wont bite enough for me to use pliers to remove it. I am afraid of hammering the extractor into the screw any more for fear of damaging the mortar/electrical box and escalating it into a more expensive problem!


r/electrical • • 22h ago

Christmas Lights

Thumbnail
gallery
3 Upvotes

Is it safe to install Christmas lights here? Me and my wife just recently bought our first house and we’re (I’m) going to line our house with lights, but I just want to make sure about this area before hopping up on the roof. Thanks!


r/electrical • • 1h ago

Lights flickering and then burn out

Post image
2 Upvotes

Lights in different rooms are flickering then burning out. I replaced them with new light bulbs, and the same thing happened. Is there a loose neutral somewhere possibly or something else? I recently got a new dishwasher installed. I will check the connections on that next.


r/electrical • • 2h ago

Is my light fixture scorching my ceiling?

Post image
2 Upvotes

I'm not usually home at this time of day, when there's natural light to see things very clearly, but just noticed brown "patches" on my ceiling above this light fixture... They're not shadows, I got up on a chair and moved the lights around to make sure.

Could the bulbs be getting hot enough to burn the paint on my ceiling? (Thankfully it's a concrete ceiling).

The bulbs are 40W halogen and the light fixture has been here since we moved in, so at least 10 years old.

I suppose I could change to LEDs and it would stop, right? Or do I maybe have a more serious issue happening here?

thanks!


r/electrical • • 15h ago

Grounding light fixture?

Thumbnail
gallery
2 Upvotes

I have a pretty old chandelier attached to a dimmer switch. I wanted to swap it out for a more modern fixture but saw the ground wire is just wrapped around a metal bar that screws into the box (see photos). Is this acceptable or do I need to call an electrician to fix the grounding?


r/electrical • • 16h ago

Smart Thermostat

Post image
2 Upvotes

This might be better suited for an HVAC thread or smart home but I thought I’d try electrical first. I want to install a smart thermostat and I was checking the needed specs for the device. Is this top one W or O/B because on the manufacturer site it wanted to know if I had one or the other of that type of wire.


r/electrical • • 16h ago

Thoughts on water damage

Thumbnail
gallery
2 Upvotes

Hello - realized recently my water panel took on some water. The breakers have a little bit of surface rust but screws and connections look alright. Panel is relatively new. Want to know if you see anything major here that I should be concerned about in the short term


r/electrical • • 2h ago

Breaker in new house

Post image
1 Upvotes

r/electrical • • 3h ago

It looks like a boil has appeared, is it due to overheating?

Thumbnail gallery
1 Upvotes

r/electrical • • 10h ago

Quick question

Post image
1 Upvotes

Hey guys.

I have a three gang switch at my entryway wired exactly like this. The left switch, has always been hooked up but it never actually turned anything on which has been weird but I lived with it. The middle switch is for the entry ceiling light and the right switch is for the exterior soffit lights.

The other day, my wife bumped into the wall next to the switches and all the lights went out. I checked the breaker and nothing was tripped. I ended up switching out the old metal three gang box for an old work blue box and installed three new Lutron switches. However, the lights still aren’t working. I flipped every switch on the breaker panel just in case and the lights still aren’t working. Has anyone seen this before and have any solutions? Just checking before I start cutting into walls to trace the romex for shorts or other issues.


r/electrical • • 14h ago

AFCI tripping while gaming

1 Upvotes

Hey all,
I have a 2018 house with a Schneider home line panel installed.
Since playing GTA 6 for the last few days now my 15amp AFCI that my PS5 is plugged into has tripped twice now.
I have replaced the breaker after the first time it did it on Thursday but it did it again tonight.
Happens after around 2-3 hours of playing. Happens completely out the blue.
It happened a couple of years ago as well with God of War Ragnarok, but hasn’t happened since, until Thursday.
I have a 10 year old dimmable lamp plugged into the circuit as well.
I don’t want to replace my PS5 until I’ve made sure everything else is okay.
Any suggestions would be appreciated.
Thanks!

EDIT: Could be worth mentioning that my PS5 is an OG day 1 fat PS5 from 2020. I’m not a hardcore gamer by any means either. Just casual.


r/electrical • • 15h ago

Fluorescent to LED conversion

Thumbnail gallery
1 Upvotes

I picked up a 20-pack of GE LED15ET8G4840 4' LED bulbs a couple of years ago on sale at Lowes. Was planning on converting a bunch of fluorescent lights to LED. Turns out these wouldn't work with the generic fixtures I had, so I shelved it until later. Well later arrived and I started playing with some of the ballast-bypass solutions online. I've tried applying 120v hot to one and both terminals on either end, with neutral to the other, as well as power and neutral to either pin on one end or the other, but no reaction. Tried the same with a 12v 18a Ryobi battery, but nothing. I figured there should at least be some type of resistance across pins, but nothing with any combination tried. I'm seeing some comments that a Type A ballast is needed, but I'm not sure which one. Would appreciate any suggestions as to which process I need to use, and what part is needed if necessary.


r/electrical • • 18h ago

Replacement Part for Discontinued Item

Thumbnail reddit.com
1 Upvotes

Replacement Part for Discontinued Item

I'm trying to find a Bezel for an old Nutone 9965 Ceiling Fan, light and Heater. It was discontinued in 2020 and the Bezel which holds the light lens is cracked.

Thanks


r/electrical • • 19h ago

Replacing old switch with a dimmer switch, need help, please

Thumbnail
gallery
1 Upvotes

My switch has 2 black, 1 white, 1 red wire. Trying to replace it with a switch that only has 3 screws (2 gold, 1 copper) and a green ground wire. Is this compatible? If so, how do I install it?


r/electrical • • 20h ago

SOLVED Can I connect a OttLite PL-0015 lamp to this power adapter?

Post image
1 Upvotes

The photos are the lamp, the label on the connector on the side of the lamp (middle top), the label on the bottom of the lamp (middle bottom) and the label on the power adapter I want to use. The lamp does light up with that power adapter. I just want to be sure it's not going to catch fire or whatever. And if I should use a different power adapter, what should that power adapter say?


r/electrical • • 21h ago

Fairy lights made my kitchen light flicker and it made a noise. Should I be worried?

1 Upvotes

Hi, I’m looking for some advice because something just happened and it’s made me quite anxious.

I plugged in a set of fairy lights in my living room, and briefly after the light above the kitchen started flickering. At the same time, it also made a noise (I’m not entirely sure how to describe it). I turned the kitchen light off and back on, and it seems to be working normally now.

I’ve unplugged the fairy lights and haven’t plugged them back in. The kitchen light is currently working normally, and I haven’t noticed any smoke or burning smell.

Is it possible this was just a brief power fluctuation, or could the noise and flickering indicate a loose connection, faulty fairy lights, or an electrical issue? Should I be concerned or have it checked by an electrician?

Thanks!


r/electrical • • 23h ago

Pendant light help

Thumbnail
gallery
1 Upvotes

First time working w/ electrical. 1 wire marked hot, another marked neutral, would that make the third wire my ground? Just confused because in the videos I watch they are usually bare copper wires. Also the actual copper wire connected to the bolt is what I connect to the copper wire from the ceiling? Sorry for the stupid questions, trying to prevent burning my house down, thanks in advance


r/electrical • • 11h ago

what’s going on with my electricity/power?

0 Upvotes

yesterday morning my mom was blow drying her hair and also had a small plug in heater on in the same room. after she turned off the blowdrier, we lost power. we assumed it was the same as before, this happened in the past, but it never happened after turning off the blow dryer, only when both were on.

we soon realized it was just our bedrooms that were affected, no where else in the house, not even the bathroom and closet connected to my room. we called our neighbor who helped us fix it in the past, but to no avail, it didn’t work this time, which is when he told us to call the property manager. we called him this morning, he sent some electricians, and everything went back to normal. however; after my mom went to bed, sometime between the 2 ish hour gap between her going to bed and me getting ready for bed, i realized we had no functioning lights in the house except the living room. just the living room

i fiddled with the fuse box, and i ended getting the power back on in every room except ours, same dilemma as yesterday. i accidentally switched on a useless light switch in my room, which made a loud pop sound, followed by a burning smell? now none of the power works except the living room once again.

the issue is, nothing happened between my mom going to bed and me getting ready. the only two outlets that were used was the one with the heater on in her room, and the living room with the light and my phone charger. just wondering if anyone could have a possible solution.


r/electrical • • 14h ago

Any info on how to troubleshoot open grounds?

Thumbnail
gallery
0 Upvotes

I replaced the outdoor lights a year ago with ones that had an outlet on them. I am almost positive I made sure it was grounded because I plugged my pool pump into it. (I know, but ..). The light deteriorated in the Texas sun. Today when I replaced the light with a 2 gang for 2 outlets, I get open ground. It's a 20amp circuit, and 12/2 wire and I wired it up like this image as I've done a few times before- its the end of the line. Part of todays plan was to also change one of the outlets before these to a CGFI for more protection. I because I'm going to still plug in the pump and now add some lights. Turns out, the outlets before this one aren't grounded either Why would 14/2 not be grounded? Getting in my attice to this line is pretty much a no go for me. Any troubleshooting or info or videos? I've wired a lot of things in my life, but I'm stumped. Thx


r/electrical • • 21h ago

Debugging a cabinet light install

0 Upvotes

We are trying to change the color of our cabinet lights - there is a little puck with two pairs of wires on the bottom of a cabinet, and inside an upper cabinet there are two pairs of wires, along with the cabjnet LED leads and an MEC driver. The guy who did this put male/female connectors on all the leads to work with the driver. But, we can’t figure out how to make use of it to change colors.

As shown in the video above, I can plug one of the wire leads (male) into the driver, but then all the lights start flashing, as if the driver was being shorted. The other one is wired as a female connector. All the cabinet connectors are working and are wired as male connectors.

Any ideas?