r/overclocking • • 6h ago

Intel Nova Lake leaks

Thumbnail
gallery
32 Upvotes

the bLLC variant , on a z990

*intel extreme profile ( iccmax 380a )

unlocked power full avx2 load ( vrm p-out 320w )

-

8x P-core 5100mhz * 5200mhz only when 2 cores r active ( separate vcore didcated to the p-core )

16x E-core 4600mhz ( separate vcore didcated to the e-core )

4x LP E-core 2200mhz ( VCCSA )

ring 4500mhz ( separate vcore didcated to the ring )

L3 cache size 144mb

D2D 3000mhz ( VNNAON )

NGU 3000mhz ( VCCSA )

tjmax 100c stock ,, configurable up to 110c on z990 * not recommended

-

DLVR is still part of the chip ,,, because of the hotspots and the nature of the 2nm size of the compute die

*we gonna have 4 separate voltage rails from the vrm to the compute die instade of a single vcore

one for each , ring , pcore, ecore , *to lower the hot spot issue.

it was suggested ,but many of the motherboard manufacturer (asus one of them) weren't happy with it ,,, because it will increase the cost and the complexity of the motherboards.

,it is still not confirmed yet,

dlvr outputs voltages

p-core at 1.150v

E-core at 0.950v

ring at 1.200v

-

cinebench r23 score is at 42000

cinebench r26 score is at 10000

-

the p core ratio will drops to 5100mhz under full avx2 load

no avx512 support the small traces cant handle it.

4x LP E-core will lower the idle wattage to 20w from 40w at idle. browsing will be at 50w

*with the unlocked power and it has it's own saprate cache,,,

disabling it along side the c state will only improve the latency

what is the bottlenecks on this gen for the bLLC ?

pcore + ecore + ring hotspots and thermal limitations / NGU / IMC and the gear 2

D2D can support up to 3900mhz so not really.

gaming performance is good ... equal to amd x3d.

the none bLLC variant is good but will be copy and paste from the arrow lake flagship variant with a slightly better cache.

and slightly better hotspots distribution *only if they separated the vcore rails.

it also will have a higher cinebench r23 score *at 45000

another note : the broken avx offset finally got replaced with somthing similar to amd pbo.

they called it FVB "frequency velocity boost".

each voltage rail of these will have a separate load line... p core / e core / ring / vccsa

with an optional sagment 2 load line for the pcore only good for high pcore ratios stability when gaming

unofficial dlvr bypass mode is still available like the arrow lake ... but not recommended ... without dlvr the hot spots r not manageable

igpu ... they added only 2 more cores to the same igpu tile found on the arrow lake.

*all of these r from an internal trusted source who works for intel.


r/overclocking • • 1h ago

Help Request - RAM Crucial Pro OC 32GB DDR5 6400MHz CL32 to 6000MHz CL30 With a 7800X3D

1 Upvotes

Hey, everyone - just making this post to ask for some assistance with my RAM speeds on my 7800X3D. I know that running 6400MHz CL32 on a 7800X3D is generally quite unstable and will usually result in the memory controller going into 2:1 mode, so as a result I've been running my Crucial RAM with the EXPO II profile of 6000MHz CL36-38-38-44 to circumvent this. However, I was wondering if I could potentially get more out of this RAM by downclocking to CL30 from this EXPO profile but am unsure as to how to do it. I've seen that Micron dies are more difficult to tighten that Samsung and Hynix dies, but I'd like some insight into if it's possible. For example, what subtimings and voltage would I set? Should I start from the 6000 CL36 profile and tighten from there or the 6400MHz CL32 profile and downclock that? I've never done any manual tuning with RAM before so any help would be greatly appreciated. Thanks, guys!


r/overclocking • • 1h ago

5585 Core Effective 13700k Cinebench r23 10 minute OC (e-cores off)

1 Upvotes

Vids are kind of high though it just sits at 5.6 all core sitting at idle with 1.423 VID max in the desktop no apps open. I got it to run 5700 all core in heavy threaded UE5 games but vids were sitting at like 1,483 for too long I think. Is this thing gonna fry itself like this?


r/overclocking • • 2h ago

Overclocking rx 5700xt red devil

1 Upvotes

i have te red devil and i would want to overclock it for better gaming performance but i can only achieve like 2100mhz at 1.2 voltage if i unlock the voltage what would be the max safe voltage for daily driving that will not destroy the silicon


r/overclocking • • 21h ago

250kf rtx 5080 , 6000cl36 vs 8200cl38

Post image
30 Upvotes

Bf6 1080p, low TAA , Mirak rush.


r/overclocking • • 14h ago

Need help with “cpu fused boost clock limit” 9850X3D

Post image
7 Upvotes

Hello people!
I have never heard about anything like this.
It seems that my cpu is locked zo 5.65 ghz?
I noticed because not even on single core benchmarks did it exceed that value while giving it +100mhz with -20 all core pbo.
If this cannor be changed , is there a reason to still put 100 mhz plus on it? I guess not?
And is there any benefits from pbo like this?


r/overclocking • • 12h ago

is undervolting a 13600KF on a Gigabyte B760M Gaming X DDR4 Gen 5 basically impossible without triggering CEP?

3 Upvotes

Hey everyone,

trying to undervolt my i5-13600KF on a Gigabyte B760M Gaming X DDR4 Gen 5 (latest BIOS) and I'm hitting a brick wall with IA CEP

at stock (Intel Default / 181W limits), I get around 22,868 in Cinebench R23, pulling ~158W at 79°C max. wanted to drop temps/power a bit and push the score closer to 24k, so I went into BIOS and tried the usual stuff:

Switched Select MCU to Rev 0x104 and set PerfDrive to Spec Enhance,

Tried setting a negative Internal CPU Vcore Offset (-0.080V) in Adaptive mode - completely ignored, VID stayed around 1.27V,

Tried Dynamic Vcore (DVID) at -0.080V - barely did anything, temps stayed around 77°C

Tried lowering IA AC Loadline directly (tested 30 and 55, default auto was 70). Voltage dropped, but CEP immediately kicked in and tanked my R23 multi-core score down to ~19,200–20,800

Looked everywhere in Advanced CPU Settings / Internal VR Control and there's no option to disable IA CEP at all (assuming Intel locked it out for 13th gen on B760) Has anyone managed to actually undervolt a 13600K/KF on this specific board (or similar Gigabyte B760 boards) without CEP clock stretching killing performance? Or am I stuck just running stock / finding the exact AC Loadline floor right above where CEP triggers?


r/overclocking • • 7h ago

Help with ram timings

1 Upvotes

Hey all a little new to optimizing ram timings. Kit I have is Crucial Pro 2x16GB 6400MT 32 40 40. I'm actually running expo 2 at the moment which is 6000 36 38 38 because it can run 1:1 UCLK stable (obviously). I've tried tweaking my expo 1 to be at least be 1:1 but within 20 minutes of an OCCT memory benchmark, errors occur. Been seeing some really cool tweaks in this subreddit and in awe how low and stable some people can get their latency to be. Just wondering if anyone with the same kit has had success optimizing theirs to be fast/stable or some words of advice or if I'm unlucky. CPU is 9800x3d motherboard is MSI Pro B850P Wifi


r/overclocking • • 18h ago

Any RAM timings worth tightening or adjusting further?

Post image
6 Upvotes

This is my first time manually tuning RAM timings, so I'd really appreciate some feedback from more experienced overclockers.

Are there any timings I could tighten further, or anything else you'd recommend adjusting based on my ZenTimings screenshot?

So far, I've run TestMem5 for 6 hours and y-cruncher for another 6 hours, with no errors in either test.

Any advice or suggestions would be greatly appreciated. Thanks in advance!


r/overclocking • • 10h ago

RTX 3070 (Gigabyte OC Vision) undervolt, 1800MHz @ 950mV, stable in every game I've tried and runs way cooler

1 Upvotes

My Gigabyte RTX 3070 OC Vision was hitting 90°C+ in games so I finally sat down and undervolted it with MSI Afterburner. this is the most stable setup I've found so far, no crashes in any game I've tried.

temps now:

  • AAA games: around 69-70°C
  • heavy modded games: around 75°C
  • before: 90°C+

settings:

  • Core voltage: +0
  • Power limit: 100
  • Temp limit: 83
  • Memory clock: +1000 (shows 8000 MHz in AB)
  • Curve: flattened at 1800 MHz @ 950mV, everything after 950mV is locked at the same clock so it never goes above that voltage

to do the curve, open the curve editor (Ctrl+F), find the 950mV point and drag it up to 1800, then hit apply so everything past it flattens out.

driver is 621.24.

every chip is different so if yours crashes, try dropping the clock a bit or bumping the voltage up to 962/975mV. curious what other 3070 owners are running, drop yours below.


r/overclocking • • 23h ago

Aimed for Top 100 in Time Spy on air, somehow hit #18 in the world w/ 9800X3D + 5070 Ti

8 Upvotes

My goal was just to crack Top 100 on a completely stock, air-cooled daily rig—no shunt mods, no XOC BIOS, no crazy cooling, just pure BIOS, RAM, and GPU curve/fabric tuning.

Ended up blowing straight past Top 100, into the Top 20, and now I'm sitting at #18 overall. The wildest part is I still messed up a bunch of runs along the way and definitely haven't hit the ceiling yet.

I'm going for Top 5 or Top 3 tonight. and will be streaming live.


r/overclocking • • 14h ago

Gigabyte AORUS RTX 5080 MASTER – Up to 30°C GPU Hotspot Delta! Is This Normal, a Cooling Defect, or Should I RMA?

Thumbnail
gallery
1 Upvotes

Gigabyte AORUS RTX 5080 MASTER – Up to 30°C GPU Hotspot Delta! Is This Normal, a Cooling Defect, or Should I RMA?

Gigabyte AORUS RTX 5080 MASTER – Up to 30°C GPU Hotspot Delta! Is This Normal, a Cooling Defect, or Should I RMA?

Hi everyone,

I built a new gaming PC back in September with the following specifications:

  • CPU: AMD Ryzen 9 9950X3D
  • RAM: 64GB DDR5 6000MHz CL30
  • GPU: Gigabyte AORUS GeForce RTX 5080 MASTER 16GB
  • Resolution: 2560 × 1440 (1440p)

I spent quite a bit of time researching different RTX 5080 models before purchasing this card. I specifically chose the AORUS MASTER because of its premium cooling design and generally positive thermal reviews.

I've been using the card for approximately two months, and until recently, I was completely satisfied with it.

I haven't noticed any significant performance issues, FPS drops, crashes, or instability.

Even in demanding games at 1440p with maximum graphics settings and ray tracing/path tracing enabled, my GPU core temperature generally stays around 60–65°C.

However, while running some benchmark tests out of curiosity, I discovered something that has me quite concerned.

The Problem: A 26–30°C GPU Hotspot Delta

After researching other owners' results, I found several reports of the same RTX 5080 MASTER running with GPU-to-hotspot temperature differences of approximately 8–15°C.

My card, however, behaves very differently depending on the workload.

In certain stress tests, the GPU core temperature stays around 60–67°C, while the GPU hotspot reaches 90–94°C.

This results in a 26–30°C temperature delta between the GPU core and hotspot sensors.

My Test Results

All tests were performed at an ambient room temperature of approximately 23–25°C.

TestGPU TempGPU HotspotDelta
FurMark (10-minute mark)57°C70°C13°C
AIDA64 GPU Stress Test62.6°C92.2°C29.6°C
OCCT (5-minute mark)67.4°C93.6°C26.2°C
Marvel's Spider-Man 2 (1440p, RT, Ultra)60–62°C78–87°C18–25°C
GTA V Enhanced (1440p, RT, Ultra)60–62°C78–87°C18–25°C

During 3DMark testing, the hotspot also reaches approximately 91°C and can remain at that temperature under sustained load.

What concerns me most is the inconsistency between workloads.

For example:

  • FurMark: Only a 13°C delta.
  • AIDA64: Almost a 30°C delta.
  • OCCT: More than a 26°C delta.
  • Demanding games: Often an 18–25°C delta.

I understand that different workloads can produce different temperature distributions across the GPU die.

However, I'm unsure whether this level of variation is expected for this particular card.

Case Cooling and Airflow

I believe my system has excellent airflow.

My cooling configuration includes:

  • 3 bottom intake fans
  • 3 front intake fans
  • 1 rear exhaust fan
  • A top-mounted 420mm AIO radiator with fans
  • All 3 original GPU fans
  • The additional fan included with the AORUS MASTER, installed above the graphics card

All GPU fans are working properly.

The fact that my GPU core and VRAM temperatures generally remain around 60–65°C also suggests that overall cooling performance is quite good.

Troubleshooting I've Already Tried

To rule out software or firmware-related problems, I've tried the following:

  1. Updated the GPU VBIOS.
  2. Tested different NVIDIA driver versions.
  3. Switched to the GPU's secondary BIOS.
  4. Ran multiple benchmark and stress-testing applications.
  5. Cross-checked temperature readings using different GPU monitoring programs, including MSI Afterburner.

Unfortunately, the hotspot behavior remains similar.

I haven't opened the graphics card or removed the heatsink because I don't want to risk my warranty or disturb the factory-applied thermal interface material.

What Could Be Causing This?

My main suspicions are:

  • Uneven contact between the GPU die and heatsink/vapor chamber.
  • Uneven application or distribution of the factory composite metal thermal grease.
  • Incorrect mounting pressure or another heatsink assembly issue.
  • Less likely, a temperature sensor or monitoring software issue.

These are only possibilities, not confirmed diagnoses.

My Biggest Concern: Summer Temperatures and Long-Term Reliability

The ambient temperature during all my testing was only 23–25°C.

During summer, the temperature in my room can become considerably higher.

If the GPU hotspot is already reaching 90–94°C under current conditions, I'm worried about how the card will behave during hotter months.

I also wonder whether a consistently large hotspot delta could affect the card's long-term reliability, even if gaming performance currently appears normal.

Questions for RTX 5080 Owners and Hardware Experts

I'd really appreciate some advice from people who own this specific GPU or have experience with GPU cooling systems.

  1. Is a 26–30°C hotspot delta normal for the Gigabyte AORUS RTX 5080 MASTER?
  2. If you own the same model, what GPU core, VRAM, and hotspot temperatures do you see in OCCT, AIDA64, 3DMark, and demanding games?
  3. Why would FurMark produce only a 13°C delta while AIDA64 and OCCT produce almost 30°C?
  4. Could this indicate poor heatsink contact, uneven mounting pressure, or an issue with the factory thermal interface material?
  5. Could this temperature difference cause long-term reliability problems even without noticeable thermal throttling?
  6. Since the card is relatively new and still under warranty, should I contact Gigabyte for an RMA or request a replacement from the retailer?
  7. Are there any additional diagnostic tests I can perform without disassembling the card?

Just to clarify: My GPU performs well in games, and I haven't experienced crashes or obvious performance degradation. My concern is the unusually large hotspot delta compared with results I've seen from other owners of the same model.

I really don't want to send a relatively new, expensive graphics card in for warranty service unnecessarily, especially when I'm otherwise happy with it.

But at the same time, I don't want to ignore a potential manufacturing or cooling issue that might become worse over time.

I've attached screenshots of my benchmark and temperature monitoring results.

If anyone with the same AORUS RTX 5080 MASTER could share their own hotspot temperatures and deltas, that would be extremely helpful.

Thanks in advance for any advice or suggestions!


r/overclocking • • 9h ago

Pea-sized blob results in poor thermal paste coverage

Post image
0 Upvotes

My AIO performance was not doing so well for my i9-12900K, so I went to repaste and reseat the cooler, but noticed that the top and bottom of the IHS are basically paste-free. Seems like this would definitely cause poor overall contact with the IHS.

When I apply paste I always use a decent sized blob in the middle (perhaps too much, but that’s the better side to err on than too little). I expected that it would spread everything out evenly, but as you can see it did not.

What method do you use to apply paste with actually even coverage? Spread manually?


r/overclocking • • 9h ago

Trying to find a program that auto-tunes MSI Afterburner for a better power curve

0 Upvotes

A few months back someone posted some tool that hooks into MSI Afterburner to adjust power draw. I think the point was that normal 100% power draw from your GPU is not needed and this was better performance and cost savings. The software required Afterburner and it ran some automated hooks after install.

I have now completely forgotten what that was and can't find a trace of it on my PC. But I have recently installed Win11 and wanted to get it reinstalled. Anyone familiar with what I may be talking about?

Thanks!


r/overclocking • • 20h ago

Esoteric 5090 Waterforce coil whine under an AI upscaling load, pulsing about 8 times a second. Sewing machine or helicopter?

1 Upvotes

30 fans in this build and somehow they’re not the loud part.

This is my 5090 Waterforce running an AI upscaling batch. Yes, I know it’s coil whine. The GPU doesn’t.

To me it sounds like an old sewing machine. The GPU disagrees. It’s the most expensive thing in this build and it knows it. According to the GPU, it’s a state-of-the-art helicopter, thank you very much.

Sound on please.

So who’s right? Sewing machine or helicopter?

OC setup
CPU: 285K tuned with Intel XTU / RAM: Corsair Vengeance 96GB DDR5-6000, XMP Tweaked / GPU: GIGABYTE AORUS GeForce RTX 5090 XTREME WATERFORCE 32G, stock

Audio analysis
I had Claude run a spectral analysis on the audio: a steady tone around 1-1.5 kHz, pulsing about 7.7 times a second.

Note: I’m Korean, living in Seoul, and my English isn’t great. All the ideas and jokes here are mine. AI just translates them into English, for this post and my replies. If something sounds a little too polished, blame the translator, not me.

Originally posted on nvidia, sharing it here too.


r/overclocking • • 1d ago

Help Request - RAM Do i need to lower the subtimins more ?

Post image
2 Upvotes

This what i archive primary timing wont go lower without errors so i want to know if it is worth it to lower the subtimins more if they will give a noticeable difference without causing instability


r/overclocking • • 1d ago

Help Request - CPU 9950x3d after the latest Windows update, the temperature in idle mode increased.

Thumbnail
gallery
2 Upvotes

Hello everyone.

Previously, the temperature of my 9950x3d in idle was ~52-55 degrees (HYDROSHIFT II LCD-C + Lian Li TL + noctua nt-h2)

Presumably, after the KB5132061 update (but I don’t know exactly when), the temperature reaches 60–61 degrees after 10–15 minutes of inactivity and doesn’t drop. At the same time, the temperature remains the same when playing games.

(I also noticed that stuttering sometimes appears in the game that wasn’t there before (but it might have appeared with the game update). I also have the feeling that the computer itself is running slower and stuttering, even though the CPU isn’t under load.

I checked, the KB5132061 update installed normally, it’s not looping. The settings in the BIOS haven’t been changed. The mode is balanced. I’ve attached the remaining screenshots.


r/overclocking • • 21h ago

static oc 9800X3D

0 Upvotes

i want to try a static oc on my 9800x3d, but don’t know how to do it, is there some guide out there? Mainly play cs2 at high elo, trying to maximize 1% lows

specs:
x870 Tuf Plus
9800x3d
9070xt
2x16 (32gb) ram
1x 1TB m2
1x 512gb m2

running 2200fclk, 1.19 vsoc, -20 +200mhz all core, LLC level 5, nitro 121

i can give more information if needed


r/overclocking • • 23h ago

Benchmark Score Overclocking results for 5090 & 9800X3D Time Spy, Time Spy Extreme, Port Royal, and Steel Nomad at Stock 600W Limit

Thumbnail
gallery
1 Upvotes

Runs were completed at +415 Core, +3000 Memory, +500 xBar Clock, and +500 SYS Clock

Time Spy - 44,708 with GPU of 60,164 & CPU 18,206

Time Spy Extreme - 21,933 with GPU of 31,301 & CPU of 8,136

Port Royal - 45,628 GPU

Steel Nomad - 17,381 GPU


r/overclocking • • 1d ago Bravo

XOC Gear I need some dice or LN2

Post image
7 Upvotes

I ran my 5090 in speedway and cranked out a 20K score using xOCD by nothoov. This astral is insane!


r/overclocking • • 1d ago

Benchmark Score Sub-40°C 5090 Waterforce & 30 Fans: Quick-Swap Wiring, Fan Backs & 3DMark Scores

Thumbnail
gallery
29 Upvotes

Following up on my previous note with the wiring behind the loop, the rear view of the 30 fans, and the full 3DMark results.

Every connector is color-coded and hand-labeled for rapid teardowns and swaps without disassembling the entire rig. That practical setup is how the 5090 Waterforce stays below 40°C under full load.

Steel Nomad: 14,938 (149.38 FPS) Time Spy Extreme: 23,899 (GPU 26,904) Time Spy: 39,718 (GPU 49,564)

※ Since I am a Korean living in Seoul and not fluent in English, I used Gemini to translate this. Please understand even if some expressions feel awkward.


r/overclocking • • 1d ago

5070ti Mvolt+ oc/uv help

3 Upvotes

Card model: https://www.techpowerup.com/gpu-specs/palit-rtx-5070-ti-gamingpro-s-oc.b12649

Currently using 0.950v 2950mhz settings using MSI Afterburner.

But i want to oc/uv my card for extra performance with using mvolt+ program. How should i start?


r/overclocking • • 1d ago

OC Report - CPU Ryzen 9600x full core OC

Post image
5 Upvotes

got my 9600x today replacing my 2-3 year old 7500 f static OC all cores at 5.4 vcore at 1.13 25 min in occt steady fixed setting on CPU stability test what are your opinions and any way to get better results


r/overclocking • • 1d ago

Help Request - CPU 9800x3d died G.Skill ULL Kit + Asus Auto CPU VDDIO/MC was probably the isse - help needed

3 Upvotes

Hi Guys,

my 9800x3d found dead after 17,5 months of use.

6 weeks after i got my hands on ths Kit F5-6000A2636H16GX2-TZ5NXRK my PC wont boot, hangs with error code 62 while white led is on. I know this phase initializes Pcie - Southbrige (correct me if im wrong) but with no Gpu in slot and cmos rest still no post or display output via igpu.
Guess my Chip is fried ..

So i was wondering if 1.447 CPU VDDIO/MC was the isssue here, the only value i was wondering if this will be save 24/7. VSoc at 1.2V
I use ZenTimings and HWinfo for monitoring. As i remember reading where about the same.
Cant post ZenTimings screenshot, dont have access right now.

All Voltages set on Auto (i kow my fault - dont blame asus or amd just want to identify root cause and make shure failure wont continue on my new system)

Ive cross tested this, the extrem VDDIO was set b ymy board to run this Kit with expo timings.

Sadly cant find docs from amd mentioning guidlines for save voltages. Maybe some on can hel me out :)

ROG STRIX X870E-E GAMING WIFI
BIOS 2402
ComboAM5 PI 1.3.0.1b Patch A

Maybe those set limits got adjusted in the new agesa but i also dont know..

If u need further information i ll try to provide. Still searching for the ZenTimings reading..