r/overclocking • • 11h ago

Pea-sized blob results in poor thermal paste coverage

Post image
0 Upvotes

My AIO performance was not doing so well for my i9-12900K, so I went to repaste and reseat the cooler, but noticed that the top and bottom of the IHS are basically paste-free. Seems like this would definitely cause poor overall contact with the IHS.

When I apply paste I always use a decent sized blob in the middle (perhaps too much, but that’s the better side to err on than too little). I expected that it would spread everything out evenly, but as you can see it did not.

What method do you use to apply paste with actually even coverage? Spread manually?


r/overclocking • • 22h ago

Esoteric 5090 Waterforce coil whine under an AI upscaling load, pulsing about 8 times a second. Sewing machine or helicopter?

0 Upvotes

30 fans in this build and somehow they’re not the loud part.

This is my 5090 Waterforce running an AI upscaling batch. Yes, I know it’s coil whine. The GPU doesn’t.

To me it sounds like an old sewing machine. The GPU disagrees. It’s the most expensive thing in this build and it knows it. According to the GPU, it’s a state-of-the-art helicopter, thank you very much.

Sound on please.

So who’s right? Sewing machine or helicopter?

OC setup
CPU: 285K tuned with Intel XTU / RAM: Corsair Vengeance 96GB DDR5-6000, XMP Tweaked / GPU: GIGABYTE AORUS GeForce RTX 5090 XTREME WATERFORCE 32G, stock

Audio analysis
I had Claude run a spectral analysis on the audio: a steady tone around 1-1.5 kHz, pulsing about 7.7 times a second.

Note: I’m Korean, living in Seoul, and my English isn’t great. All the ideas and jokes here are mine. AI just translates them into English, for this post and my replies. If something sounds a little too polished, blame the translator, not me.

Originally posted on nvidia, sharing it here too.


r/overclocking • • 23h ago

static oc 9800X3D

0 Upvotes

i want to try a static oc on my 9800x3d, but don’t know how to do it, is there some guide out there? Mainly play cs2 at high elo, trying to maximize 1% lows

specs:
x870 Tuf Plus
9800x3d
9070xt
2x16 (32gb) ram
1x 1TB m2
1x 512gb m2

running 2200fclk, 1.19 vsoc, -20 +200mhz all core, LLC level 5, nitro 121

i can give more information if needed


r/overclocking • • 8h ago

Intel Nova Lake leaks

Thumbnail
gallery
43 Upvotes

the bLLC variant , on a z990

*intel extreme profile ( iccmax 380a )

unlocked power full avx2 load ( vrm p-out 320w )

-

8x P-core 5100mhz * 5200mhz only when 2 cores r active ( separate vcore didcated to the p-core )

16x E-core 4600mhz ( separate vcore didcated to the e-core )

4x LP E-core 2200mhz ( VCCSA )

ring 4500mhz ( separate vcore didcated to the ring )

L3 cache size 144mb

D2D 3000mhz ( VNNAON )

NGU 3000mhz ( VCCSA )

tjmax 100c stock ,, configurable up to 110c on z990 * not recommended

-

DLVR is still part of the chip ,,, because of the hotspots and the nature of the 2nm size of the compute die

*we gonna have 4 separate voltage rails from the vrm to the compute die instade of a single vcore

one for each , ring , pcore, ecore , *to lower the hot spot issue.

it was suggested ,but many of the motherboard manufacturer (asus one of them) weren't happy with it ,,, because it will increase the cost and the complexity of the motherboards.

,it is still not confirmed yet,

dlvr outputs voltages

p-core at 1.150v

E-core at 0.950v

ring at 1.200v

-

cinebench r23 score is at 42000

cinebench r26 score is at 10000

-

the p core ratio will drops to 5100mhz under full avx2 load

no avx512 support the small traces cant handle it.

4x LP E-core will lower the idle wattage to 20w from 40w at idle. browsing will be at 50w

*with the unlocked power and it has it's own saprate cache,,,

disabling it along side the c state will only improve the latency

what is the bottlenecks on this gen for the bLLC ?

pcore + ecore + ring hotspots and thermal limitations / NGU / IMC and the gear 2

D2D can support up to 3900mhz so not really.

gaming performance is good ... equal to amd x3d.

the none bLLC variant is good but will be copy and paste from the arrow lake flagship variant with a slightly better cache.

and slightly better hotspots distribution *only if they separated the vcore rails.

it also will have a higher cinebench r23 score *at 45000

another note : the broken avx offset finally got replaced with somthing similar to amd pbo.

they called it FVB "frequency velocity boost".

each voltage rail of these will have a separate load line... p core / e core / ring / vccsa

with an optional sagment 2 load line for the pcore only good for high pcore ratios stability when gaming

unofficial dlvr bypass mode is still available like the arrow lake ... but not recommended ... without dlvr the hot spots r not manageable

igpu ... they added only 2 more cores to the same igpu tile found on the arrow lake.

*all of these r from an internal trusted source who works for intel.


r/overclocking • • 11h ago

Trying to find a program that auto-tunes MSI Afterburner for a better power curve

0 Upvotes

A few months back someone posted some tool that hooks into MSI Afterburner to adjust power draw. I think the point was that normal 100% power draw from your GPU is not needed and this was better performance and cost savings. The software required Afterburner and it ran some automated hooks after install.

I have now completely forgotten what that was and can't find a trace of it on my PC. But I have recently installed Win11 and wanted to get it reinstalled. Anyone familiar with what I may be talking about?

Thanks!


r/overclocking • • 16h ago

Need help with “cpu fused boost clock limit” 9850X3D

Post image
7 Upvotes

Hello people!
I have never heard about anything like this.
It seems that my cpu is locked zo 5.65 ghz?
I noticed because not even on single core benchmarks did it exceed that value while giving it +100mhz with -20 all core pbo.
If this cannor be changed , is there a reason to still put 100 mhz plus on it? I guess not?
And is there any benefits from pbo like this?


r/overclocking • • 23h ago

250kf rtx 5080 , 6000cl36 vs 8200cl38

Post image
30 Upvotes

Bf6 1080p, low TAA , Mirak rush.


r/overclocking • • 3h ago

Help Request - RAM Crucial Pro OC 32GB DDR5 6400MHz CL32 to 6000MHz CL30 With a 7800X3D

2 Upvotes

Hey, everyone - just making this post to ask for some assistance with my RAM speeds on my 7800X3D. I know that running 6400MHz CL32 on a 7800X3D is generally quite unstable and will usually result in the memory controller going into 2:1 mode, so as a result I've been running my Crucial RAM with the EXPO II profile of 6000MHz CL36-38-38-44 to circumvent this. However, I was wondering if I could potentially get more out of this RAM by downclocking to CL30 from this EXPO profile but am unsure as to how to do it. I've seen that Micron dies are more difficult to tighten that Samsung and Hynix dies, but I'd like some insight into if it's possible. For example, what subtimings and voltage would I set? Should I start from the 6000 CL36 profile and tighten from there or the 6400MHz CL32 profile and downclock that? I've never done any manual tuning with RAM before so any help would be greatly appreciated. Thanks, guys!


r/overclocking • • 14h ago

is undervolting a 13600KF on a Gigabyte B760M Gaming X DDR4 Gen 5 basically impossible without triggering CEP?

3 Upvotes

Hey everyone,

trying to undervolt my i5-13600KF on a Gigabyte B760M Gaming X DDR4 Gen 5 (latest BIOS) and I'm hitting a brick wall with IA CEP

at stock (Intel Default / 181W limits), I get around 22,868 in Cinebench R23, pulling ~158W at 79°C max. wanted to drop temps/power a bit and push the score closer to 24k, so I went into BIOS and tried the usual stuff:

Switched Select MCU to Rev 0x104 and set PerfDrive to Spec Enhance,

Tried setting a negative Internal CPU Vcore Offset (-0.080V) in Adaptive mode - completely ignored, VID stayed around 1.27V,

Tried Dynamic Vcore (DVID) at -0.080V - barely did anything, temps stayed around 77°C

Tried lowering IA AC Loadline directly (tested 30 and 55, default auto was 70). Voltage dropped, but CEP immediately kicked in and tanked my R23 multi-core score down to ~19,200–20,800

Looked everywhere in Advanced CPU Settings / Internal VR Control and there's no option to disable IA CEP at all (assuming Intel locked it out for 13th gen on B760) Has anyone managed to actually undervolt a 13600K/KF on this specific board (or similar Gigabyte B760 boards) without CEP clock stretching killing performance? Or am I stuck just running stock / finding the exact AC Loadline floor right above where CEP triggers?


r/overclocking • • 16h ago

Gigabyte AORUS RTX 5080 MASTER – Up to 30°C GPU Hotspot Delta! Is This Normal, a Cooling Defect, or Should I RMA?

Thumbnail
gallery
1 Upvotes

Gigabyte AORUS RTX 5080 MASTER – Up to 30°C GPU Hotspot Delta! Is This Normal, a Cooling Defect, or Should I RMA?

Gigabyte AORUS RTX 5080 MASTER – Up to 30°C GPU Hotspot Delta! Is This Normal, a Cooling Defect, or Should I RMA?

Hi everyone,

I built a new gaming PC back in September with the following specifications:

  • CPU: AMD Ryzen 9 9950X3D
  • RAM: 64GB DDR5 6000MHz CL30
  • GPU: Gigabyte AORUS GeForce RTX 5080 MASTER 16GB
  • Resolution: 2560 × 1440 (1440p)

I spent quite a bit of time researching different RTX 5080 models before purchasing this card. I specifically chose the AORUS MASTER because of its premium cooling design and generally positive thermal reviews.

I've been using the card for approximately two months, and until recently, I was completely satisfied with it.

I haven't noticed any significant performance issues, FPS drops, crashes, or instability.

Even in demanding games at 1440p with maximum graphics settings and ray tracing/path tracing enabled, my GPU core temperature generally stays around 60–65°C.

However, while running some benchmark tests out of curiosity, I discovered something that has me quite concerned.

The Problem: A 26–30°C GPU Hotspot Delta

After researching other owners' results, I found several reports of the same RTX 5080 MASTER running with GPU-to-hotspot temperature differences of approximately 8–15°C.

My card, however, behaves very differently depending on the workload.

In certain stress tests, the GPU core temperature stays around 60–67°C, while the GPU hotspot reaches 90–94°C.

This results in a 26–30°C temperature delta between the GPU core and hotspot sensors.

My Test Results

All tests were performed at an ambient room temperature of approximately 23–25°C.

TestGPU TempGPU HotspotDelta
FurMark (10-minute mark)57°C70°C13°C
AIDA64 GPU Stress Test62.6°C92.2°C29.6°C
OCCT (5-minute mark)67.4°C93.6°C26.2°C
Marvel's Spider-Man 2 (1440p, RT, Ultra)60–62°C78–87°C18–25°C
GTA V Enhanced (1440p, RT, Ultra)60–62°C78–87°C18–25°C

During 3DMark testing, the hotspot also reaches approximately 91°C and can remain at that temperature under sustained load.

What concerns me most is the inconsistency between workloads.

For example:

  • FurMark: Only a 13°C delta.
  • AIDA64: Almost a 30°C delta.
  • OCCT: More than a 26°C delta.
  • Demanding games: Often an 18–25°C delta.

I understand that different workloads can produce different temperature distributions across the GPU die.

However, I'm unsure whether this level of variation is expected for this particular card.

Case Cooling and Airflow

I believe my system has excellent airflow.

My cooling configuration includes:

  • 3 bottom intake fans
  • 3 front intake fans
  • 1 rear exhaust fan
  • A top-mounted 420mm AIO radiator with fans
  • All 3 original GPU fans
  • The additional fan included with the AORUS MASTER, installed above the graphics card

All GPU fans are working properly.

The fact that my GPU core and VRAM temperatures generally remain around 60–65°C also suggests that overall cooling performance is quite good.

Troubleshooting I've Already Tried

To rule out software or firmware-related problems, I've tried the following:

  1. Updated the GPU VBIOS.
  2. Tested different NVIDIA driver versions.
  3. Switched to the GPU's secondary BIOS.
  4. Ran multiple benchmark and stress-testing applications.
  5. Cross-checked temperature readings using different GPU monitoring programs, including MSI Afterburner.

Unfortunately, the hotspot behavior remains similar.

I haven't opened the graphics card or removed the heatsink because I don't want to risk my warranty or disturb the factory-applied thermal interface material.

What Could Be Causing This?

My main suspicions are:

  • Uneven contact between the GPU die and heatsink/vapor chamber.
  • Uneven application or distribution of the factory composite metal thermal grease.
  • Incorrect mounting pressure or another heatsink assembly issue.
  • Less likely, a temperature sensor or monitoring software issue.

These are only possibilities, not confirmed diagnoses.

My Biggest Concern: Summer Temperatures and Long-Term Reliability

The ambient temperature during all my testing was only 23–25°C.

During summer, the temperature in my room can become considerably higher.

If the GPU hotspot is already reaching 90–94°C under current conditions, I'm worried about how the card will behave during hotter months.

I also wonder whether a consistently large hotspot delta could affect the card's long-term reliability, even if gaming performance currently appears normal.

Questions for RTX 5080 Owners and Hardware Experts

I'd really appreciate some advice from people who own this specific GPU or have experience with GPU cooling systems.

  1. Is a 26–30°C hotspot delta normal for the Gigabyte AORUS RTX 5080 MASTER?
  2. If you own the same model, what GPU core, VRAM, and hotspot temperatures do you see in OCCT, AIDA64, 3DMark, and demanding games?
  3. Why would FurMark produce only a 13°C delta while AIDA64 and OCCT produce almost 30°C?
  4. Could this indicate poor heatsink contact, uneven mounting pressure, or an issue with the factory thermal interface material?
  5. Could this temperature difference cause long-term reliability problems even without noticeable thermal throttling?
  6. Since the card is relatively new and still under warranty, should I contact Gigabyte for an RMA or request a replacement from the retailer?
  7. Are there any additional diagnostic tests I can perform without disassembling the card?

Just to clarify: My GPU performs well in games, and I haven't experienced crashes or obvious performance degradation. My concern is the unusually large hotspot delta compared with results I've seen from other owners of the same model.

I really don't want to send a relatively new, expensive graphics card in for warranty service unnecessarily, especially when I'm otherwise happy with it.

But at the same time, I don't want to ignore a potential manufacturing or cooling issue that might become worse over time.

I've attached screenshots of my benchmark and temperature monitoring results.

If anyone with the same AORUS RTX 5080 MASTER could share their own hotspot temperatures and deltas, that would be extremely helpful.

Thanks in advance for any advice or suggestions!